Banner Q4X Series Manual de usuario

Q4X BASICS

1. For black/dark targets and highly reflective targets, set the “SPd” to 50ms

2. If using a reflective target, put a 5-15° tilt on the sensor to avoid specular reflection

3. Always try and make sure the green “STB” light is solid on the display of the sensor

4. Locking and Unlocking The Sensor - Press and hold the “+” button and tap the “-“ button four times. This can

both lock and unlock the Q4X sensor and the display with flash the condition (“Loc” or uLoc”).

Q4X Factory Default Reset

1. Press and hold the MODE/- button for more than 2 seconds until “tch” shows up on the display.

2. Press the MODE/- button once. The display will read “rSEt” for Reset.

3. Press Select/TEACH button to enter the Reset submenu.

4. The display should read “no”. Press the “-“ button once. The display will read “yes”.

5. Press the SELECT/TEACH button to reset the sensor to factory defaults and return to Run mode.

Q4X Adjust Switch Point/ Window Size

1. In run mode click + or –button (momentary). Current switch point will display (flashing slowly)

2. Use + and –buttons to in adjust position.

3. Click SELECT/TEACH to confirm the adjusted switch point

Q4X Active TEACH Indicators (DYN, FGS, and BGS)

1. Two-point TEACH mode selected (default) —DYN, FGS, and BGS all off

2. Dynamic TEACH mode selected —DYN on

3. Foreground suppression TEACH mode selected —FGS on

4. Background suppression TEACH mode selected —BGS on

5. Dual TEACH mode selected —DYN, FGS, and BGS all on

Q4X –Set Teach Mode

The Q4X has 5 teach modes, Two Point Teach (2-Pt), Background Suppression (BGS), Foreground Suppression (FGS),

Dynamic Teach (DYn), and Dual Mode (duAL). These can be accessed with the following steps

1. Press MODE for 2 seconds ("out" will show in display, press + to get to “tch”)

2. Click SELECT / TEACH

3. Click + / - until the desired teach mode appears on the display (see above for abbreviated names)

4. Click SELECT/TEACH to select mode

5. Press and Hold SELECT/TEACH for 3 seconds to exit menu and return to run mode.

Q4X-TWO POINT TEACH (“2-pt” MODE on sensor) Sets a single switch point midway between two targets

TO PROGRAM THE SENSOR FOR THE APPLICATION

1. Press TEACH for longer than 2 seconds:

2. The display will flash between SEt and 1St.

3. Focus laser on target

4. Press SELECT / TEACH to teach first point

5. The display will flash between SEt and 2nd.

6. Place 2nd part under laser.

7. Press SELECT / TEACH to teach second point

THE DISPLAY WILL FLASH THE SWITCH POINT THEN

THE SENSOR WILL RETURN TO RUN MODE

Q4X-BACKGROUND SUPPRESSION (“BGS” MODE) switch point set based on the position of the background

TO PROGRAM THE SENSOR FOR THE APPLICATION

1. Press TEACH for longer than 2 seconds

2. Focus laser on target (part)

3. Press SELECT / TEACH to teach the

part position

THE DISPLAY WILL FLASH THE SWITCH POINT THEN

THE SENSOR WILL RETURN TO RUN MODE

Q4X-WINDOW DETECTION (“FGS” MODE on sensor) Sets a window around a target.

TO PROGRAM THE SENSOR FOR THE APPLICATION

1. Press TEACH for longer than 2 seconds

2. Focus laser on target (part)

3. Press SELECT / TEACH to teach the

part position

THE DISPLAY WILL FLASH THE SWITCH POINT THEN

THE SENSOR WILL RETURN TO RUN MODE

Q4X-Contrast + Distance Detection (“DuAL” MODE on sensor) Sensor will switch off at less than 75% of

reference intensity and distance (Teach reference target on fixture (on / 100)

TO PROGRAM THE SENSOR FOR THE APPLICATION

1. Press TEACH for longer than 2 seconds (sensor

will flash between SEt and on)

2. Focus laser on surface that is fixed where the

object will pass through

3. Press SELECT / TEACH to teach 100% intensity,

display will flash and read 100P

THE SENSOR WILL RETURN TO RUN MODE

Otros manuales para Q4X Series

Tabla de contenidos

Otros manuales de Accesorios de Banner

Banner

Banner Q4X Series Manual de usuario

Banner

Banner iVu TG Manual de usuario

Banner

Banner Q3X Manual de usuario

Banner

Banner Q5X Manual de usuario

Banner

Banner Registration Mark Sensor R58 Expert Manual de usuario

Banner

Banner Q4X Series Manual de usuario

Banner

Banner L-GAGE LE250 IO-Link Manual de usuario

Banner

Banner L-GAGE LTF Manual de usuario

Banner

Banner Q5X Manual de usuario

Banner

Banner R-GAGE T30R Manual de usuario

Banner

Banner Sensors T-GAGE M18T Manual de usuario

Banner

Banner QS30 Series Manual de usuario

Banner

Banner L-GAGE LE250 IO-Link Manual de usuario

Banner

Banner R-Gage Q130RA-AF Manual de usuario

Banner

Banner WORLD-BEAM QS18E Manual de usuario

Banner

Banner T30RW Manual de usuario

Banner

Banner D10 Expert Manual de usuario

Banner

Banner Q5X Manual de usuario

Banner

Banner Q4X Series Manual de usuario

Banner

Banner iVu Plus BCR Manual de usuario

Banner

Banner iVu Plus TG Series Manual de usuario

Banner

Banner iVu Series Manual de usuario

Banner

Banner D10 Expert Series Manual de usuario

Banner

Banner L-GAGE LT7PIDQ Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario