B&G h3000 Guía del usuario
www.bandg.com
System Installation
Guide
H3000 System Installation Guide
3
IS-2530-01
B&G
NOTIFICATION
The information contained in this document is subject to change without prior
notice.
Navico Holding shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance or use of
this document.
No part of this work covered by the copyright hereon may be reproduced or
otherwise copied without prior permission from Navico Holding.
© 2009 Navico Holding. All rights reserved.
B&G
Premier Way, Abbey Park,
Romsey, SO51 9DH,
United Kingdom
Tel: +44 1794 518448
Fax: +44 1794 518077
www.bandg.com
email: [email protected]
email: [email protected]
H3000 System Installation Guide
4IS-2530-01
LIABILITY AND SAFETY WARNINGS
Navico Holding accept no responsibility for the use and/or operation of this
equipment. It is the user’s responsibility to ensure that under all circumstances the
equipment is used for the purposes for which it has been designed.
Warning: Electrical Hazard
This equipment uses high voltage electrical power. Contact with high voltages may result in
injury and/or loss of life.
Warning: Calibration
The safe operation of this equipment is dependent on accurate and correct calibration.
Incorrect calibration of this equipment may lead to false and inaccurate navigational readings
placing the yacht into danger.
Warning: Operational Hazard
The H3000 system is an Electronic Navigation aid and is designed to assist in the navigation
of your yacht. It is not designed to totally replace conventional navigation procedures and
precautions and all necessary precautions should be taken to ensure that the yacht is not
placed into danger.
The Pilot is an aid to steering the vessel. It is the users responsibility to ensure the safe
control and movement of the vessel at all times.
Caution: Electrical Supply
This equipment is designed for use with a power supply source of 12V dc. The application
of any other power supply may result in permanent damage to the equipment.
Caution: Cleaning
The use of alcohol or solvent-based cleaners will damage this equipment and any warranty
in force will be invalidated.
Caution: Display Installation
Displays installed into locations manufactured from conductive materials (e.g. Steel, Carbon
Fibre etc.) should be insulated from the structure to prevent damage to the casings as a result
of the effects of electrolysis.
Caution: Processor Installation
All B&G Processors should be installed below decks in a dry location protected from water
and moisture.
Power Off Disclaimer
When in standby mode the H3000 system continues to consume power. To conserve the
vessel’s battery life switch off power at the main breaker.
H3000 System Installation Guide
5
IS-2530-01
ABOUT B&G
B&G has welcomed the constant challenge to develop new electronic solutions
for every sailor’s need. Harnessing technical developments and providing proven
solutions has continued to be the focus that keeps B&G on the leading edge of
advanced marine electronics.
Proven in the worlds most testing environments, B&G offers the most accurate
and reliable systems used by blue water cruisers, single-handed racers and record
breakers alike, firmly establishing ourselves as one of the leading innovators of the
most highly advanced marine electronics. B&G is renowned for tried and trusted
solutions and is ever evolving to offer the best technology to the customer.
B&G’s Promise.
“Uncompromising performance, precision and reliability from both our
products and our people”.
ABOUT THIS HANDBOOK
Instructions in this handbook describe the installation and routine maintenance of
your H3000 system.
H3000 System Installation Guide
6IS-2530-01
SYSTEM INTRODUCTION
H3000 is the successor to the leading Hydra 2000 and Hercules 2000 instrument
and Pilot systems from B&G.
Hydra and Hercules 2000 and its predecessors have been used and depended upon
by the worlds serious cruising and racing fraternity for fifty years, during which
time the systems have been constantly evolving to provide the most dependable
instrument and autopilot systems available.
At the heart of every H3000 System is the Central Processor Unit (CPU).
Depending upon your system choice, this will either have Hydra, Hercules,
Hercules Performance or Hercules Motion software enabled.
The CPU integrates raw data from sensors and makes them available on a choice of
displays anywhere in the yacht. The modular design allows you to progress from a
standard system, adding new units or software as required.
This manual describes the standard system and then describes how the system can
be expanded.
The system is connected together by the Fastnet communication network, which
handles all of the data that travels between devices: including the CPU, analogue
displays, Graphical Display (GFD), Pilot Display (GPD) and HV Displays.
Analogue displays are connected to a GFD via the Simnet network.
These combined with the wind speed and angle, compass heading, boat speed and
depth sensors make up the standard system.
H3000 System Installation Guide
7
IS-2530-01
H3000 SYSTEM EXAMPLE
Above is an example of a typical H3000 system. At the centre of the system is the
Central Processor Unit (CPU).
All sensor information is fed back to the CPU and can be easily controlled and
configured via the Graphical Function Display (GFD).
H3000 System Installation Guide
8IS-2530-01
PROCESSOR
CENTRAL PROCESSING UNIT (CPU)
The CPU is the core of the H3000 system, taking the majority of sensor inputs and
using a dedicated processor to rapidly calculate and calibrate further functions and
distribute them to display units and external devices.
The new enclosure enhances ease of installation with its plugged connections. The
CPU is function upgradeable to enable the purchase of upgrades for additional
functionality. This means upgrading your system is straightforward.
As well as sensor inputs there is also a USB interface that allows straight-
forward connection of a PC for either NMEA communications or the H-Link™
communication protocol used by software packages such as Deckman.
The H3000 CPU is supplied with powerful software functions that include easy to
use, highly accurate AutoCal calibration tools to bring the established power of the
H3000 system calibrations to all users.
H3000 System Installation Guide
9
IS-2530-01
There are four software levels available:
Hydra
Hydra provides class leading performance and is ideally suited for cruising
applications:
Multiple sensor inputs for external sensors (Barometer, Air and Sea
Temperature etc.)
AutoCal routines to simplify otherwise complex calibration procedures
Up to 4Hz update rates
True Wind Corrections
USB interface for interfacing NMEA data to a PC
NMEA 0183 input and output
Alternative use of SOG as boat speed
Hercules
A software level designed specifically to meet the requirement of racing and
advanced cruising applications. Hercules adds the following:
Up to 6Hz update rates
Dynamic Damping
Wind data corrected for Heel angle
Advanced TWS calibration
Secondary Pulse input for additional boat speed sensor
Boat speed linearity/heel angle correction
Hercules Performance
Designed to further enhance the H3000 range, the Hercules Performance level
software integrates B&G’s Tactical Navigation software, Deckman, along with
several advanced features:
Deckman™ Tactical Navigation software
H-Link™ communications (USB or RS232), USB lead included
Polar tables
Polar related performance functions (e.g. Target Boat Speed)
H3000 System Installation Guide
10 IS-2530-01
Hercules Motion
Hercules Motion uses technology from B&G’s grand prix level systems to
calculate and correct wind data for the errors induced by the motion of the yacht.
This includes all features and functions from Hercules Performance. Additional
features include:
Performance Wind Filter (PWF)
Pitch and Roll measurement
Wind Motion Correction
EXPANSION PROCESSOR
The Expansion Processor provides 12 additional linear/analogue sensor inputs.
HALCYON GYRO PROCESSOR
The Halcyon Gyro Processor is an interface between the Halcyon Gyro Stabilised
Compass and the B&G Fastnet network. It also outputs NMEA heading information
at a rate of 10Hz for use with other marine instruments and AD10 for use with
Radar.
The Halcyon Gyro Processor accepts NMEA data from your position fixer for
magnetic variation information to allow display and output of True referenced
heading.
The Halcyon Gyro Processor can also be used as an interface to output NMEA
heading and AD10 from a B&G system compass, or to accept NMEA heading
information from an external compass for use on the H3000 system.
Otros manuales para h3000
2
Tabla de contenidos
Otros manuales de Sistema de navegación para automóviles de B&G
