Balanced Audio Technology REX Manual de usuario
1
REX
WARRANTY REGISTRATION FORM
Unit Serial Number: _______________________________________
Customer Name: _______________________________________
Address: _______________________________________
_______________________________________
Date of Purchase: _______________________________________
Purchased From:
Dealer Name: _______________________________________
Address: _______________________________________
_______________________________________
IMPORTANT NOTE:
In order to receive the full five year product warranty, please mail this completed
form together with a copy of your sales receipt to Balanced Audio Technology at the
address below, within thirty days of purchase.
Failure to do so will result in the product being warrantied for one year from the
date of manufacture.
1300 First Stat Blvd. Suite A Wilmington DE 19804 Tel: 302-999-8855 Fax: 302-999-8818
2
REX
Vacuum Tube
Balanced Stereo Preamplifier
Owner's Manual
1300 First Stat Blvd. Suite A Wilmington DE 19804 Tel: 302-999-8855 Fax: 302-999-8818
3
TABLE OF CONTENT
CURRENT SOURCES 4
CHANGING CURRENT SOURCES 5
AC SHUNT VOLTAGE REGULATORS 6
INTRODUCTION 7
Package Content 7
Physical Placement 8
Configuring the REX 8
Connecting to your system 9
FRONT PANEL CONTROLS 10
REX Power On sequence 10
Turning the REX Off 10
PHASE Button and LED 11
MONO button and LED 11
MUTE button and LED 11
INPUT selection 11
VOLUME knob 11
DISPLAY format 12
FUCTION button 12
DISPLAY Brightness function 13
MUTE function 13
REX PROGRAMMABLE FUNCTIONS 14
Parameter Definitions 15
PROGRAMMING THE REX 15
BALANCE adjustment 15
VOLUME offsets 16
PHASE 17
MONO/STEREO 17
MAXIMUM gain 17
FIXED gain 18
DISPLAY MODE 18
INPUT NAME 19
REMOTE CONTROL FUNCTIONS 20
Volume Up/Down 20
Mute 20
Fade 20
Input 20
Display/Power 21
Fuse Protection 21
Servicing 21
Cleaning 21
RESETTING THE REX 22
WARRANTY 23
4
Vacuum Tube Current Sources in REX
Your REX incorporates a unique feature that allows you to optimize its sound to tailor it to your
individual taste or system requirements.
The Vacuum Tube current sources incorporated in the REX, being part of the signal gain stage, have a
direct effect on the unit’s sound. Changing the tube type used in that circuit allows the user an extra
degree of control over the sound of the unit.
In its standard configuration the REX current sources use the Russian 6C19 tubes. That tube is basically
a miniature version of the famous 6C33 tube, and provides, in our view, the best combination of sonic
characteristics and electrical performance.
However, the unique design of the REX allows you to also use other tube types in that application.
Currently, the user has the following three choices for vacuum tube Current Sources:
1. The standard 6C19 tube current source as installed from the factory.
2. The 6H30 SuperTube current source which requires the purchase of the X-PAK accessory.
3. The 5881 tube current source.
NOTE: There are TWO Current Sources in REX, located in the Power Module.
The REX X-PAK accessory includes two current source boards.
5
In order to change the tube type the user needs to remove the installed Current Source boards, and replace
them with either another type, designed for a particular tube type, or install the 5881 tubes as a direct plug-in.
Only the 5881 tubes can be used directly upon the removal of the 6C19 current source board.
Please consult the factory regarding options for other tube types that may be available in the future.
WARNING:
The following procedure should only be performed by qualified personnel
To change the current source:
1. Turn the unit OFF and wait at least 5 minutes to allow the tubes to cool down and the power
supply charge to dissipate. Remove the Power Module top cover.
2. Remove the six screws holding each current source board.
3. Pull the current source boards straight up to disengage its connectors.
4. Install the new current source boards making sure their connectors are properly aligned. Boards
will be positioned properly when the mounting holes in the circuit boards align with the standoffs.
5. Install the six mounting screws.
6. Turn the unit ON.
6
AC SHUNT VOLTAGE REGULATORS
The REX preamplifier incorporates another feature that allows the user to optimize its sound – the
AC Shunt voltage regulators.
The AC Shunt voltage regulators perform the final “cleaning” of the REX power supply rails. They
work to reduce the minute fluctuations in the DC voltages that may degrade the sound.
The AC Shunt Voltage Regulators are located in the REX Power Module.
They incorporate two types of vacuum tubes, user selectable for the desired sound: 6C45 and 6H30.
To change the AC Shunt tube type remove the Power Module top cover and move the board-mounted
switch S1 to desired position. The switch is located close to the center of the board.
Only the selected tubes will have their filaments running at any time.
7
INTRODUCTION
Thank you for your purchase of the Balanced Audio Technology REX preamplifier. Please
read this owner's manual to obtain the full benefit of the REX in your system. It will provide you
with the needed safety information and operating procedures for this exceptional unit.
WARNINGS:
To prevent the possibility of serious injury, electrical shock or fire:
DO NOT operate with the cover removed.
DO NOT expose to rain or moisture.
DO NOT defeat the ground power-plug.
DO NOT replace fuse with anything other than the same type and rating as supplied by the factory.
Package Contents
Included in the box set should be the following:
Description Quantity
REX Control Module 1
REX Power Module 1
Power Cord 2
Spare Fuse 2
Torx Wrench (T-10) 2
Spare Top Cover Screws 10
User’s Manual 1
VK-R3 Remote Control (If ordered)
8
Save all the packaging material in a safe dry area for the unlikely event that you need to return
the REX to the factory for service.
PHYSICAL PLACEMENT
It is recommended that you provide at least 6" of free space around each module comprising the REX
preamlifier for proper ventilation.
Mount the modules on a hard surface with proper ventilation underneath.
Do not stack the REX preamplifier on top of other units, nor vice versa.
WARNING
Stacking the modules (putting the Control Module on top of the Power Module)
is NOT permitted.
CONFIGURING THE REX PREAMPLIFIER SYSTEM
The REX preamplifier system consists of two modules.
Control Module performs all the control functions associated with the duties of the
preamplifier in your system. It also receives and processes the remote control commands.
Power Module works in conjunction with the Control Module as an outboard power supply.
The two modules are connected by two detachable cables. In addition each module has its own
power cord that must be plugged into the power outlet.
WARNING
Make sure your REX is powered DOWN before making or changing ANY
connections between its two modules, to the source components or power
amplifiers.
Connect the two detachable cables between the modules, making sure the channels are connected
properly.
Plug the two power cords into power receptacles.
Make all the signal connections.
9
CONNECTING THE REX TO YOUR SYSTEM
Balanced Components
Use balanced XLR interconnects. All input and output connectors are clearly marked on the back
panel.
Note: The REX XLR connectors are wired as follows:
Pin 1: common/shield
Pin 2: positive
Pin 3: negative
For the REX, use the Main 1 XLR Output for connection to your balanced power amplifier. The
Output 2 is configured as an RCA connector output.
Single-Ended Components
Single-ended components have RCA connectors. The REX preamplifier is designed to work
with balanced interconnects only. If single ended components need to be connected to the
preamplifer, then the RCA/XLR adapters should be used. These adapters are available from an
authorized Balanced Audio Technology dealer at a nominal charge.
Two types of adapters are available:
Input Adapters: RCA Female to XLR Male
Output Adapters: RCA Female to XLR Female.
10
REX FRONT PANEL CONTROLS
STANDBY Button and LED
The Standby button is used to turn the unit ON and OFF and to switch the preamplifier into its
Standby mode. The LED indicates the status of the unit’s power circuitry and has four state:
LED OFF Display OFF Unit is in OFF state
Display ON Unit is in ON state
LED Flashing Unit is going through its Power-ON routine
LED ON Unit is in its STANDBY mode
When the unit is plugged into a power line, it will stay in the OFF state until the Standby button is
pushed. The LED will then start blinking and the unit will go through a 50second warm-up sequence.
At the end of that sequence it will turn ON.
Pressing the button again will switch the unit into its Standby mode.
The REX can be turned OFF by pressing and holding the Standby button.
REX Power-On sequence:
When you turn the REX On, it will automatically go through a gentle power-on sequence. This
sequence takes 50 seconds, during which time the display and the Standby LED will be flashing,
indicating the status of the unit.
In addition, the blue LED on the Power Module front panel will also light.
1. The number on the display during this time indicates the volume setting. This will usually
start at 000. This setting can be changed during this time by using the volume knob or
Volume Up/Down buttons on your VK-R3 remote control transmitter. In addition, such
functions as Phase, Mono, input selection and Mute can be changed during this time either
from front panel or through the remote control.
2. Normally the REX will be not muted (Mute LED on the display is OFF) and will begin playing
at the end of the 50 second delay. If so desired, the unit can be put in the MUTE mode during
this delay interval either by depressing the front panel MUTE switch or by using the MUTE
button on the VK-R3 remote control transmitter.
Turning the REX Off:
The unit can be turned OFF by pressing and holding the Standby button. It will automatically mute.
Tabla de contenidos
Otros manuales de Amplificador de Balanced Audio Technology
Balanced Audio Technology
Balanced Audio Technology VK-P3 Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-33 Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-50 Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-3i Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-5i Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-5SE Manual de usuario
Balanced Audio Technology
Balanced Audio Technology REX II Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-75SE Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-55 Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-150SE Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-31SE Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-250 Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-30SE Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-51SE Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-200 Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-P5 Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-53SE Manual de usuario
Balanced Audio Technology
Balanced Audio Technology Phono Module Manual de usuario
Balanced Audio Technology
Balanced Audio Technology REX II Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-5 Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-220 Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-52SE Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-150 Manual de usuario
Balanced Audio Technology
Balanced Audio Technology VK-31 Manual de usuario
