B-Link Basic Charger-32A Manual de usuario
Installation Manual
Basic/Smart/Intelligent Charger-32A Revision 4.0
www.tritium.com.au
Veel®isaregisteredtrademarkofTritiumPtyLtd.©2018TritiumPtyLtd
BlinkCharging.com • (888) 998.2546
©2019 Blink Charging Co. • NASDAQ: BLNK
BlinkCharging.com • (888) 998.2546
©2021 Blink Charging Co. • NASDAQ: BLNK
Basic/Smart/Intelligent Charger-32A Installation Manual Rev. 4.0
BlinkCharging.com • (888) 998.2546
©2021 Blink Charging Co. • NASDAQ: BLNK
I
IMPORTANT SAFETY INSTRUCTIONS
This document contains instructions and warnings that must be followed when installing and
using the Electric Vehicle Supply Equipment (EVSE). Before installing or using the EVSE, read this
entire document as well as WARNING and CAUTION markings in this document.
Safety Instructions
The symbols used have the following meaning:
The charge point must be installed only by licensed electricians.
Make sure that the materials used and the installation procedures follow local building
codes and safety standards.
The information provided in this manual in no way exempts the user of responsibility to
follow all applicable codes or safety standards.
This document provides instructions for the charge point and should not be used for any
other product. Before installation or use of this product, review this manual carefully and
consult with a licensed contractor, licensed electrician, or trained installation expert to make
sure of compliance with local building codes and safety standards.
WARNING: RISK OF PERSONAL INJURY
WARNING: RISK OF ELECTRIC SHOCK
WARNING: RISK OF FIRE
CAUTION: RISK OF DAMAGE TO THE EQUIPMENT
Repair and Maintenance Clause
Only licensed electricians can repair or maintain the charge point. It is forbidden for general
users to repair or maintain it.
Turn off input power before repair or maintenance the charge point.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with greater than 20cm
between the radiator & your body.
Basic/Smart/Intelligent Charger-32A Installation Manual Rev. 4.0
BlinkCharging.com • (888) 998.2546
©2021 Blink Charging Co. • NASDAQ: BLNK
II
Industry Canada statement:
This device complies with ISED’s license-exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas
produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y
compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with greater than 20cm
between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de 20 cm entre
le radiateur et votre corps.
WARNING: RISK OF ELECTRIC SHOCK
Basic precautions should always be followed when using electrical products,
including the following:
• Read all the instructions before using this product.
• This device should be supervised when used around children.
• Do not put fingers into the EV connector.
• Do not uses this product if the flexible power cord or EV cable is frayed, has
broken insulation, or any other signs of damage.
• Do not use this product if the enclosure or the EV connector is broken,
cracked, open, or shows any other indication of damage.
• To avoid a risk of fire or electric shock, do not use this unit with an extension
cord.
WARNING: RISK OF ELECTRIC SHOCK
Improper connection of the equipment grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or serviceman if you are in doubt
as to whether the product is properly grounded.
Do not modify the plug provided with the product – if it will not fit the outlet, have a
proper outlet installed by a qualified electrician.
Basic/Smart/Intelligent Charger-32A Installation Manual Rev. 4.0
BlinkCharging.com • (888) 998.2546
©2021 Blink Charging Co. • NASDAQ: BLNK
III
SAVE THESE INSTRUCTIONS
WARNING: RISK OF ELECTRIC SHOCK
Do not remove the cover or attempt to open the enclosure. No user serviceable parts inside. Refer servicing to
qualified service personnel.
WARNING: RISK OF ELECTRIC SHOCK
• Do not touch live electrical parts.
• Incorrect connections may cause electric shock.
• Do not Disconnect Under Load.
WARNING: This equipment is intended only for charging vehicles that do not
require ventilation during charging. Please refer to your vehicle’s owner’s manual
to determine ventilation requirements.
WARNING: Do not use extender cables to increase the length of the charging cable.
Maximum length is limited to 25 feet by the National Fire Protection Agency.
WARNING: Do not drag the charge point by input power cord.
CAUTION: Do not expose to liquid, vapor or rain.
CAUTION: If this unit is installed outdoors, the outlet must be rated for outdoor
installation. The outlet must be installed properly to maintain the proper NEMA
rating of the enclosure.
• Installation work and electrical wiring must be done by qualified person(s) in
accordance with all applicable codes and standards, including fire-rated
construction.
• Do not touch the terminals or other current-carrying parts.
• Take care not to drill into any pipes or power lines beneath the surface during
mounting holes preparation. Use power line / metal detector.
• Do not trample or drive over the product’s cables.
• Do not put any foreign objects into the enclosure.
• Do not start the engine when the charging connector is still connected.
CAUTION: Do not use this product if there is any damage to the unit. Send the unit
back to the manufacturer in the event the unit is not operational.
Basic/Smart/Intelligent Charger-32A Installation Manual Rev. 4.0
BlinkCharging.com • (888) 998.2546
©2021 Blink Charging Co. • NASDAQ: BLNK
IV
1
Contents
1
Introduction ............................................................................................................................. 2
Product View ............................................................................................................... 2
2
Installation................................................................................................................................ 4
Before Installation ....................................................................................................... 4
Tools & Parts Required for Installation ........................................................................ 5
SIM Card Installation (for IC3 only) .............................................................................. 5
Install the Charge Point ................................................................................................ 7
Input cord connection (for IC3 only) .......................................................................... 11
Install the Holster....................................................................................................... 15
Basic/Smart/Intelligent Charger-32A Installation Manual Rev. 4.0
BlinkCharging.com • (888) 998.2546
©2021 Blink Charging Co. • NASDAQ: BLNK
1 Introduction
This user manual applies to “32A Level 2 AC Charger for Plug-in Electric Vehicles (PEVs) and
Battery Electric Vehicles (BEVs)”.
The Level 2 Electric Vehicle Supply Equipment (EVSE) with 32A capabilities will be used in North
America. It can provide a shorter charging time than the traditional 16A EVSE.
!!! Any unauthorized modifications will void the manufacturer’s warranty. !!!
1.1 Product View
Different models of Charger:
Basic Charger-32A (BC3) Smart Charger-32A (SC3) Intelligent Charger-32A (IC3)
Figure 1-1 Front view
2
Basic/Smart/Intelligent Charger-32A Installation Manual Rev. 4.0
BlinkCharging.com • (888) 998.2546
©2021 Blink Charging Co. • NASDAQ: BLNK
Box Contents
See the table below for differences in the box content of three models.
Figure 1-2 Box contents
Table 1-1 Accessories in the box
Item
Description
QTY
Remark
1
Basic Charger-32A (BC3)
1
Charging Plug
Input Power Cord
OLED Display
RFID Icon
Smart Charger-32A (SC3)
Charging Plug
Input Power Cord
OLED Display
RFID Icon
Intelligent Charger-32A (IC3)
Charging Plug
Input Power Cord
OLED Display
RFID Icon
2
Mounting Bracket
1
Attached to the back of the charge point
3 Holster ASSY 1
With Hook x1, Holster x1 & M4xL15 tapping
screw x2
4
Screw Bag
1
With #12xL50 tapping screw x4
3
Basic/Smart/Intelligent Charger-32A Installation Manual Rev. 4.0
BlinkCharging.com • (888) 998.2546
©2021 Blink Charging Co. • NASDAQ: BLNK
2 Installation
2.1 Before Installation
2.1.1 Safety check
• Check for transport damages.
• Before connecting the product to the power supply, check that the power supply voltage
and current rating corresponds with the power supply details shown on the product
rating label.
The charge point must be installed only by a licensed electrician in accordance with the provisions
of the local electrical industry construction and should comply with national electrical codes and
standards.
Before installing the charge point, make sure you have read all of these instructions in this manual
and fully understand its contents.
Appropriate protection is required when connecting to a main switchboard. The tools and
parts used as outlined in the section “Tools & parts required for installation”.
2.1.2 Grounding Instructions
The charge point must be implemented equipment grounding through a permanent wiring
system or an equipment grounding conductor. Use a wire with a dedicated grounding wire and a
ring terminal and connected to the equipment ground terminal block for grounding.
CAUTION: Disconnect the power supply before installing or repairing the charge
point. Failure to do so may result in physical injury or damage to the power supply
system and the charge point.
CAUTION: Avoid touching or pressing the OLED screen all times, as this may result in
damage to the OLED screen.
DANGER: RISK OF SUFFOCATION
Keep any packing materials away from children – these materials are a potential
source of danger, e.g. suffocation.
4
Basic/Smart/Intelligent Charger-32A Installation Manual Rev. 4.0
BlinkCharging.com • (888) 998.2546
©2021 Blink Charging Co. • NASDAQ: BLNK
2.2 Tools & Parts Required for Installation
Table 2-1 Tools & parts required for installation
Tool QTY Model
Size Supplier Remark
Mounting Bracket 1 All 194x109x9 mm Model Accessories Secure the charge point
Holster ASSY 1 All 58x58x70 mm Model Accessories Hold EV charging plug
Screw 4 All Tapping: #12 Model Accessories Secure Mounting Bracket &
Hook
Mechanical: M6 Commercially Available
Wire, Copper 3 IC3 8 AWG Commercially Available UL1015 (recommended)
Heat Shrink Tube 3 IC3 For 8 AWG wire Commercially Available
Terminal 3 IC3 For 8 AWG wire Commercially Available Connect input wires to the
terminal block
Conduit 1 IC3 1 inch Commercially Available
Torx Screwdriver 1 All T20 Commercially Available
Philips Screwdriver
1 All PH3 Commercially Available
Hexagon Socket 1 All 5/16 Commercially Available Tighten #12 Tapping screws
Torque Wrench 1 All 35 kgf-cm min Commercially Available
2.3 SIM Card Installation (for IC3 only)
1. Disassemble top cover
1-1 Loosen the screws (x5) on the base cover.
Figure 2-1 Position of five screws on Base Cover
5
Basic/Smart/Intelligent Charger-32A Installation Manual Rev. 4.0
BlinkCharging.com • (888) 998.2546
©2021 Blink Charging Co. • NASDAQ: BLNK
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Cargador de baterías de B-Link
B-Link
B-Link SEMACONNECT 7 Series Manual de usuario
B-Link
B-Link DS Series Manual
B-Link
B-Link HQ 200 Manual de usuario
B-Link
B-Link bluecorner PQ 150 Manual de usuario
B-Link
B-Link IQ 200 Manual de usuario
B-Link
B-Link MQ 200 Manual de usuario
B-Link
B-Link DS Series Manual
B-Link
B-Link DS Series Manual
B-Link
B-Link 6 Series Manual de usuario
B-Link
B-Link DC Fast Charger Manual de usuario
