B.E.G. WAVE-PIR-120/277 Manual de usuario
Ambient Light Level Adjustment
Control Panel Cover
LED Indicator
OFF VAC VAC
TIME
TEST
520
30
Min Min
Min RANGE
3
2
Mounting Yoke
Fresnel Lens
OFF VAC VAC
4
1
Neutral
White
Hot
Black
Ground
Green
Load
Red Load
- 01- -03-
-02-
DESCRIPTION
Part Number: 97334
Voltage .................................................................... 120/277VAC, 60Hz
Incandescent .........................................................................… 800W
Motor .............................................................................................1/4HP
Time Delay.....................................................................15Sec to 30Mins
SPECIFICATIONS
WAVE-PIR-120/277
VACANCY
SENSOR
SWITCH
INSTALLATION
Turn off the circuit breaker before installation.
WARNING:
Do not exceed electrical ratings.
Line(Hot), Red lead to Load wire, Green lead to Ground.
2. Gently position wires in wall box, attach sensor switch to the box.
3. Mount device “TOP”up.
4. Restore power at circuit breaker or fuse, wait
6. Locate the adjustment knobs on the control panel to perform test and
ADJUSTMENT
INSTALLATION INSTRUCTIONS
Light Level...................................................................... 30 Lux--Daylight
Indoor use only.
Wiring Diagram:
Figure 2
VAC
Mode
OFF
VAC
Description
Position
Left
Center
Right
Vacancy Mode: Manual On only,
automatic Off after set time delay.
React to the push-button
Manually toggles
Manually toggles
1. Connect lead wires as WIRING DIAGRAM (see Figure 2): Black lead to
Coverage Area
Band switch prescription.
5. Remove the small cover plate. (illustrated as Figure 3. )
7. Replace the small cover plate after testing and adjustment.
8. Attach the wallplate.
Figure 3
On / Off the load.
On / Off the load.
adjustment.(illustrated as Figure 3. ) Default position: 15 Seconds (Test mode)
Adjustable: from 15 Seconds to 30 Minutes (clockwise)
Default position: Center at 65%
Adjustable: 30% (Position 1) to 100% (Position 4)
Note: Turn toward right for greater room space.
Turn toward left to avoid false alert in smaller room and near
the door way or heat source.
Time Delay knob
Sensor Sensitivity Range Knob
three minutes.
Fluorescent/Ballast/LED.............. 800VA@120VAC /1600VA@277VAC
Ground wire is required.
Manually toggles
On / Off the load.
Operation Temperature....................................................... 32°F--131°F
The coverage range of the sensor switch is specified and illustrated
the light to turn off eventhough someone is still in the detection area.
in Figure 1. Large objects and some transparent barriers like glass
windows will obstruct the sensors' view and prevent detection, causing
Best: 320 sq.ft.
Figure 1
Regular: 800 sq.ft.
Maximum: 1200 sq.ft.
40'
Top View
20'
10'
20'
10'
20'
5'
4'
Circuit is permanently opened
(switched off)
After Initial Run (3 minutes), set the Band Switch to VAC, press and
hold the Manual ON/OFF Button for 6 seconds until the Load turns on,
release the button within the next 4 seconds, the Load will turn off and
stay off or a maximum 10 seconds. The Load will turn on again (2
seconds) and then Off. It confirms that the present light level becomes
(Push-button)
The passive infrared sensors work by detecting the difference between
heat emitted from the human body in motion and the background space.
If no motion is detected after the set time delay, the load turned off
automatically. The sensor switch has one relay ( equal to single pole
switch), also includes Ambient Light Level Sensor.
Figure 4
10 Min
Vacancy Mode: Manual On only,
automatic Off after set time delay.
(Test Mode), make sure there is no motion (no LED flashing), the
The Time Delay knob is default set on 15 seconds, do not adjust it until
By Pushing the Control Panel Cover, the Load can be turned On/Off
detected. To verify proper operation, turn the Time Delay Knob to 15s
-06-
-05-
INSTALLATION INSTRUCTIONS
The Sensor Switch is programmed independently for any Mode (OFF,
Manual On/Off Button
Turning On the Load under Vacancy Mode
Manual On/Off Button has to be pushed to turn On the Load.
VAC or VAC). As refer to the Band Switch position under the control
under any Mode (OFF, VAC or VAC).(illustrated as Figure 5). There
OPERATION
For proper operation, the Sensor Switch has to consume power from hot
Therefore, a
Initial run
The Sensor Switch needs
During the
initial run, the load might be turned On and Off several times.
initial run is finished and proper operation function confirmed.
The Load is out of control (frequently flashing)
1. It can take up to three minutes for initial run.
2. Check the wiring connections, especially the
The Load does not turn On without LED flashing or LED flashing
1. Push Manual On/Off Button, if the load turns On; verify that Sensitivity
Range is on high. If the Load does not turn On, go to Step 2.
2. Check the wiring connections.
The Load does not turn On while LED flashing with motion detected
1. Check to see if Ambient Light Level is enable by covering the lens
2. Push Manual On/Off Button, if the load turns On; verify that Sensitivity
Range is on high. If the Load does not turn On, go to Step 3
3. Check the wiring connections, especially Hot Line and Ground wiring.
The Load does not turn Off
1. There can be up to a 30 minutes time delay after the last motion
initial run within three minutes.
regardless of motion
2. Check if there is any significant heat source mounted within six feet (two
meters) that may cause false detection such as high wattage light bulb,
portable heater and HAVC device.
3. Check the wiring connections, especially the Ground wiring to the
The Load turns On while no desired
1. Mask the Sensor Switch’s lens to eliminate unwanted coverage area.
2. Turn the Sensitivity Level knob toward left to avoid false alert in smaller
room and near the door way.
Ground Secured Ground Wiring is required.
Ground Wiring .
panel cover.
and
by hand.
Load should turn Off in 15 seconds.
sensor switch.
TROUBLESHOOTING
the set Ambient Light Level.
is a 5 seconds re-trigger delay between ON and OFF.
-04-
3. Set the Band Switch to the VAC positon.
Automatic Turning Off the Load
Under any Mode, the sensor keeps the Load On until no motion is detected
plus the set time delay, Loads to be Off automatically.
Manual Turning Off the Load
By pushing the Manual On/Off button, the Load can be turned Off under
any Mode.
Figure 5
WARRANTY INFORMATION
B.E.G. Controls warranties its products to be free of defects in materials
and
workmanship for a period of five(5) years. There are no
obligations or
liabilities on the part of our company for consequential
damages arising
out of or in connection with the use or performance
of this product or
other indirect damages with respect to loss of property,
revenue, or profit,
or cost of removal, installation or reinstallation.
Feb, 2017
For technical support please call (770)
349-6341 and press "2" at the prompt, or
email [email protected]. Technical
support is available Monday through Friday,
8:00 AM to 5:00 PM Eastern time.
Este manual sirve para los siguientes modelos
1
Otros manuales de Cambiar de B.E.G.
