Axminster SBW3501B Manual de usuario
SBW3501B
Bandsaw
Axminster Tool Centre,
Unit 10 Weycroft Avenue, Axminster, Devon EX13 5PH
www.axminster.co.uk
Code: 501199
02
Page No.
Index of Contents 02
Declaration of Conformity 02
What’s Included 03
General Instructions for 230V Machines 03-04
Specific Safety Instructions for Bandsaws 04
Assembly Instructions 05-06
Specification 07
Illustration and Parts Description 08-09-10-11-12
Setting up the Saw 13
Operating Instructions 14
Changing the Saw Blade 15
Routine Maintenance 16-17-18
Parts List/ Breakdown 19-20-21-22-23-24-25
Wiring Diagram 26
Notes 27
Copied from CE Certificate
The undersigned, J. Robrow authorised by
OAV Equipment & Tools, Inc. No. 65, Tung-Shan Rd.,
Wu-Tso Ching-Shuei, Taichung Hsien 436 Taiwan,
R.O.C. declares that this product:
Model number: SBW-YHC Series
Y (Stands for ): 3501, 3502, 3503
Manufactured by OAV Equipment & Tools, Inc. is in
compliance with the following standards or standardisation
documents in accordance with Council Directives
prEN 61029-2-5: 1992
EN 61029-1: 2000
Warning
The symbols below advise that you follow the correct
safety procedures when using this machine.
Dust mask
should be worn
Ear protection
should be worn
Eye protection
should be worn
Fully read manual
and safety instructions
before use
HAZARD
Motor gets hot
Index of Contents
Declaration of Conformity
03
What’s Included
Quantity Item Model Number SBW3501B
1 No. Bandsaw
2 No. Stand Side Plate
2 No. Side Cover
1 No. Table
1 No. Rip Fence
1 No. Mitre Fence
1 No Fence Mounting Rail
1 No. Stand Assembly
1 No. Instruction Manual
General Instructions for 230V Machines
Good Working Practices/Safety
The following suggestions will enable you to observe good working practices, keep yourself and fellow workers
safe and maintain your tools and equipment in good working order.
WARNING!! KEEP TOOLS AND EQUIPMENT OUT OF THE REACH OF YOUNG
CHILDREN
Electrical
• Check that the mains power supply is earthed.
• Regularly check the mains lead and plug for damage.
• Ensure that a fuse of the correct amperage is fitted to
the plug.
• Ensure that any extension lead used is correctly rated
to suit the machine or power tool.
• Ensure that the power lead and any extension lead is
kept clear of the blades or other sharp obstacles.
• Do not use electrical machines or power tools in wet
or damp areas or locations.
• If a replacement mains plug is fitted at any time this
must be of the appropriate size and fitted with the
correct size of fuse.
General
• Mount the machine on a flat level surface. Secure the
machine to the surface where applicable.
• Always use machines or power tools in an uncluttered
area.To reduce the risk of accidents, avoid leaving
materials or other items within the working area and
allow clear access to all machine parts and controls.
• Clean machines by wiping with a damp soapy cloth.
Do not use solvents or cleaners that may damage
plastic parts or painted/coated surfaces. Keep water
and solvents away from all electrical components, leads
and plugs.
• When storing or leaving tools for any length of time,
spray bare metal surfaces with Axminster XMP
protective spray to minimise surface corrosion.
• Always isolate machines and power tools from the
power supply when not in use or when changing parts,
Continues Over....
04
General Instructions for 230V Machines
cutters and blades or when making any adjustments.
• Before using any machine or power tool, ensure that
all locking-nuts, chucks etc, are tightened and secure.
Check that all loose keys, spanners and other tools have
been removed.
• Always check that the correct machining or cutting
speed has been selected.
• Do not operate machinery or power tools when tired
or under the influence of alcohol, drugs or certain
medicines.
• Always ensure that long hair is tied back or retained
by a band, hat or safety helmet. Remove all loose
jewellery to prevent it from catching in rotating parts
of the machine.
WHEN USING MACHINES ALWAYS WEAR SUITABLE EYE PROTECTION,
EAR DEFENDERS AND DUST OR FUME INHALATION PROTECTION.
WARNING!! KEEP TOOLS AND EQUIPMENT OUT OF THE REACH OF
CHILDREN, UNLESS THEY ARE UNDER SUPERVISION.
Specific Safety Instructions for Bandsaws
• Use only the correct size of blade for the machine.
Ensure that the blade is sharp and that the blade
support clearances, blade tension and tracking are all
correct. Blunt and/or in-correctly set blades require
more force and make control of the work more
difficult, leading to the possibility of accidents.
• Ensure that the blade guard and top bearing
assembly is as close to the top of the work as possible.
This will both support the blade correctly and ensure
that minimum amount of blade is exposed.
• Ensure that the table and fence, if used, are fully
tightened and cannot move under load.
• Push sticks or push pads should always be used when
cutting wood on a bandsaw. If necessary, one push
stick should be used to push the wood through the
blade and another used to hold the timber up against
the fence.
• Ensure that the blade has completely stopped before
removing small scraps of wood from the table.
• Only saw timber which is lying flat on the table; work
which is curved in the vertical plane should be fully
supported along its length in a suitable jig.
• When tight curves are being cut there is a risk of the
blade jamming in the slot in the timber. Use a narrow
blade when cutting tight curves.
05
Assembly Instructions
Loosely assemble the stand, using eight M6 x 16mm bolts, nuts and washers. Place the stand flat on the floor,
check that it is standing square and then tighten up all the nuts.
With the help of a second person and/or suitable lifting equipment, lift the saw onto the stand, line up the holes
in the base with the holes in the stand and secure with eight M8 x 16mm bolts, nuts and washers.
Remove the insert (A) and pin (B) from the table and slide the table into position, being careful not to damage
the blade on the edge of slot in the table.
B
A
06
Assembly Instructions
Rotate the table through ˚ and lower into position whilst at the same time feeding the two securing bolts
through the holes in the mounting on the top of the body. Secure the table with the two plastic thumbnuts then
replace the insert and the pin.
Fit the fence mounting rail (C) to the front edge of the table using M6 x 20mm bolts and spring washers and the
fence support rail (D) to the rear edge with two M6 x16mm socket head screws and washers.
C
D
E
Fit the fence assembly (E) to the mounting rail, clamp it in position and measure the distance from the face of the
fence to the edge of the mitre guide slot at both front and back of the table. If necessary, adjust the angle
between the fence extrusion and the body of the fence by following these steps below:
1. Clamp down the fence by pushing the locking lever down.
2. Remove the four rubber grommets (F) covering the securing screws from the fence.
3. Using a 5mm Hex key loosen the four M6 socket head screws.
4. Adjust the fence until it is aligned with the mitre slot. Re-tighten the socket head screws.
(DOT NOT OVERTIGHTEN) then replace the rubber grommets.
F
Fence locking lever Mitre slot
07
Specification
Model SBW3501B
Product Code 501199
Rating Trade
Power 550W (230V)
Blade Speed 800m/min
Blade Length 2,552mm(100.1/2”)
Blade Width Min/Max 3mm(1/8”)/19mm(3/4”)
Max Width of Cut 340mm
Max Depth of Cut 200mm
Max Width of Cut with Fence 300mm
Table Size 500 x 356mm
Table Height on Stand 1,060mm
Table Tilt -5° to +45°
Table Height 490mm
Dust Extraction Outlet 100mm
Overall L x W x H 690 x 720 x 1,770mm
Weight 84kg
08
Illustration and Parts Description
Stand
Blade tension knob
Upper cover door lock
Lower cover door lock
Mitre fence
Guide fence
Blade guide height adjuster
Upper blade guard
Upper blade guide
Fence guide rail
Door closing micro switch
On/Off button
switch shroud
Fence locking lever
Upper door
Lower door
Off
On
Table
09
Illustration and Parts Description
Blade tensioner knob
Blade tension
release lever Tracking control knob
Blade tension
indicator
Blade guard
locking knob
Blade guide
height clamp
Table preset stop
Lower blade bearings
Lower wheel mounting
Dust outlet Motor
10
Illustration and Parts Description
Clamping screw
Scale pointer
Table tilt setting scale
(2) Table securing knobs
Side bearing
adjustment screws
Side bearing assembly locking screw
Side bearing assembly
locking screw
Rear bearing assembly
locking screw
Rear bearing assembly
adjusting screw
Side bearing
adjustment screws
Clamping screw
Side bearing assembly adjusting screw
Rear bearing assembly adjusting screw
Upper blade guard
Otros manuales para SBW3501B
1
Tabla de contenidos
Otros manuales de Sierra de Axminster
Axminster
Axminster AC1950B Manual de usuario
Axminster
Axminster PROFESSIONAL AP3086B Manual de usuario
Axminster
Axminster BS11 Manual de usuario
Axminster
Axminster TS-200-2 Manual de usuario
Axminster
Axminster AW405FS Manual de usuario
Axminster
Axminster MCB100A Manual de usuario
Axminster
Axminster AWHBS250N Manual de usuario
Axminster
Axminster MJ12-1600 MK11 Manual de usuario
Axminster
Axminster UV-180DS Manual de usuario
Axminster
Axminster AWSMS10 Manual de usuario
Axminster
Axminster MCB210HD Manual de usuario
Axminster
Axminster 200024 Manual de usuario
Axminster
Axminster SBW3501B Manual de usuario
Axminster
Axminster AWHBS350N Manual de usuario
Axminster
Axminster TS-250M Manual de usuario
Axminster
Axminster Excalibur EX-21 Manual de usuario
Axminster
Axminster AW405SS Manual de usuario
Axminster
Axminster Excalibur EX-16 Manual de usuario
Axminster
Axminster Excalibur EX-16 Manual de usuario
Axminster
Axminster Professional AP254TS Manual de usuario
