Axis FC-29W Guía de inicio rápido

FC-29W

9”

UN-UNIVERSAL

Dome Housing

Installation Instructions

Safe Use of Equipment

WARNING

To reduce the risks of an electric shock, do not expose inside of this

unit to rain or moisture.

Installation on a rainy day may also cause fog around the capsule.

Installation

Installation shall be done by qualified installer only and should

conform to all local codes.

Ensuring strength of supporting Dome Housing Unit

The unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit. Recommend

use 3/8” stainless screws x four (4).

Prohibit changes or modifications of equipment

You are cautioned that any changes or modifications not expressly

approved in these instructions could void your authority to operate

this equipment.

Basic Operating Environment Condition

We provide warranty for the products that are installed under normal

outdoor -20°C ~ +50°C conditions. We are unable to provide warranty

for the products which are installed indoor and exposed to constant

high temperature over +50°C and over 90% humidity.

Operating temperature and humidity of camera varies from camera to

camera. You are requested to confirm to camera specification with

camera manufacturer and housing specification with us in advance.

i.e. -20°C or below, you are requested to use additional heater and

+50°C or above you are requested to use two blowers and Sunshield.

Fasten wires tightly.

Attention:

Keep wires away from the Fan / Heater, and do not disturb

Fan/Heater’s performance

Table of contents

1. AXIS 214 PTZ network camera housing installation………………………..P.4

2. AXIS 215 PTZ network camera housing installation……………………..…P.6

3. AXIS 233D PTZ network dome camera Housing installation……………...P.8

4. AXIS P55XX series PTZ network dome camera Housing installation…....P.10

5. AXIS Q6034 PTZ network dome camera Housing installation………...….P.12

6. Installation of FC-9002 Pole Mount Bracket and Dome housing………….P.14

7. Installation of FC-9005 Ceil Mount Bracket and Dome housing …..….…..P.15

8. Installation of FC-9006 Ceil Mount Bracket and Dome housing …….....…P.16

9. Installation of FC-9007 Corner Adapter with Wall Mount Bracket and Dome

housing……………………………………………………………………….….P.17

10. Installation of FC-9008 Corner Adapter with Wall Mount Bracket and Dome

housing ………………………………………………………………….………P.18

11. Installation of FC-9009N Wall Mount Bracket and Dome housing …….....P.19

12. Installation of FC-9009 Wall Mount Bracket and Dome housing……….…P.20

13.Installation of FC-9011 Ceil Mount Bracket and Dome housing……….…..P.21

14.Dimensions …………………………….………….....................……………..P.22

1AXIS 214 PTZ network camera Housing installation

WARNING The unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of unit. Recommend use

stainless screws.

Cables

L603

Power cable to PC board and external power supply

L704

Power cable to PC board and PTZ network camera

9” dome housing

DC12V Fan+Heater

L705

Network extension cable to internet

Component Parts for Assembly

Square-shaped upper board No. 2 side board Round-shaped bottom board

Screw the camera on, through hole B,

with washer in the back No. 3 Allen Key ( for cover and wall

mount bracket tighten)

3x12 Double Washer screws for

camera to Square-shaped upper

board,

Assembly Steps of the Camera and the Dome Housing

1-1-1 1-1-2 1-1-3

Fix No. 2 side board (Hole 2) to the

round-shaped bottom board (Hole 5)

with 3x8 Double Washer screws.

Use 4x8 double washer screws to

Fix Fan/Heater side board on

Round-shaped bottom board,

connect power cable to Fan/Heater

Fix screws on back of

square-shaped upper board which

go through from back to front to fix

the camera on the square-shaped

upper board (Hole B) with 3x12

double washer screws.

Assembly Steps of the Cables

1-2-1 1-2-2 1-2-3

Use 4x8 double washer to Fix

Fan/Heater side board on

Round-shaped bottom board,

connect power cable to Fan/Heater

Connect L603 to the PC board.

Connect L704 to the PC board. Connect L704 and L705 to the

camera. Cables used for camera.

1. DC 12V FAN

2. DC 12V HEATER

3. H/SENSER

4. DC 12V OUT

5. DC 12V IN

L705 L704

L704 L603

2AXIS 215 PTZ network camera Housing installation

WARNING The unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of unit. Recommend use

stainless screws.

Cables

L603

Power cable to PC board and external power supply

L704

Power cable to PC board and PTZ network camera

9” dome housing

DC12V Fan+Heater

L705

Network extension cable to internet

Component Parts for Assembly

Square-shaped upper board No. 3 side board Round-shaped bottom board

Screw the camera on, through hole G,

with washer in the back No. 3 Allen Key ( for cover and wall

mount bracket tighten)

4x10 Double Washer screws for

camera to Square-shaped upper

board,

Assembly Steps of the Camera and the Dome Housing

2-1-1 2-1-2 2-1-3

Fix No. 3 side board (Hole 1) to the

round-shaped bottom board (Hole 6)

with 3x8 Double Washer screws.

Use 4x8 double washer screws to

Fix Fan/Heater side board on

Round-shaped bottom board,

connect power cable to Fan/Heater

Fix screws on front of square-shaped

upper board to fix the camera on

square-shaped upper board (Hole G)

with 4x10 double washer screws.

Assembly Steps of the Cables

2-2-1 2-2-2 2-2-3

Use 4x8 double washer to Fix

Fan/Heater side board on

Round-shaped bottom board,

connect power cable to Fan/Heater

Connect L603 to the PC board.

Connect L704 to the PC board. Connect L704 and L705 to the

camera. Cables used for camera.

1. DC 12V FAN

2. DC 12V HEATER

3. H/SENSER

4. DC 12V OUT

5. DC 12V IN

L704 L705

L704 L603

3AXIS 233D PTZ network dome camera Housing installation

WARNING The unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of unit. Recommend use

stainless screws.

Cables

L605P-2

Power cable to PC board and external power supply

L704P-2.0

Power cable to PC board and camera

9” dome housing

AC24V Fan+Heater

L705

Network extension cable to internet

Component Parts for Assembly

Square-shaped upper board No. 1 side board ＆L board Round-shaped bottom board

Screw the camera on, through hole E,

with washer in the back No. 3 Allen Key ( for cover and wall

mount bracket tighten)

4x10 Double Washer screws for camera

to Square-shaped upper board,

Assembly Steps of the Camera and the Dome Housing

3-1-1 3-1-2 3-1-3

Fix No. 1 side board (Hole 1) to the

round-shaped bottom board (Hole 5)

with 3x8 Double Washer screws.

Fix screws on front of square-shaped

upper board to fix the L board on

square-shaped upper board (Hole E)

with 4x10 double washer screws.

Fix the camera to the L board with

4x10 double washer screws.

Assembly Steps of the Cables

3-2-1 3-2-2 3-2-3

Use 4x8 double washer to Fix

Fan/Heater side board on

Round-shaped bottom board,

connect power cable to Fan/Heater

Connect L605P-2 to the PC board.

Connect L704P-2.0 to the PC board. Connect L704P-2.0 and L705 to the

camera. Cables used for camera.

1. DC 12V FAN

2. AC 24V HEATER

3. H/SENSER

4. DC 12V OUT

5. AC 24V OUT

6. AC 24V IN

L705 L704P-2.0

L704P-2.0 L605P-2

Tabla de contenidos

Otros manuales de Accesorios para cámaras de Axis

Axis

Axis T92G20 Manual de usuario

Axis

Axis 26426R1 Manual de usuario

Axis

Axis 01457-001 Manual de usuario

Axis

Axis 01445-001 Manual de usuario

Axis

Axis T8133 Midspan 30W Manual de usuario

Axis

Axis TP3201 Manual de usuario

Axis

Axis 01807-001 Manual de usuario

Axis

Axis 01473-001 Manual de usuario

Axis

Axis T99A10 Manual de usuario

Axis

Axis 211M Manual de usuario

Axis

Axis T91A52 Manual de usuario

Axis

Axis Videolarm 25734 Hoja de instrucciones

Axis

Axis T92A20 Manual de usuario

Axis

Axis Q1656-BE Manual de usuario

Axis

Axis VT Verso Manual de usuario

Axis

Axis T93G Series Manual de usuario

Axis

Axis T92E series Manual de usuario

Axis

Axis Q86 Front Kit A Manual de usuario

Axis

Axis T95A Series Manual de usuario

Axis

Axis T94K01L Manual de usuario

Axis

Axis T94B01L Manual de usuario

Axis

Axis AVTPSC Manual de usuario

Axis

Axis 24889 Hoja de instrucciones

Axis

Axis T92E series Manual de usuario

Manuales populares de Accesorios para cámaras de otras marcas

Viltrox

Viltrox EF-NEX Instrucciones de instalación

Calumet

Calumet 7100 Series CK7114 Manual de usuario

Ropox

Ropox 4Single Series Manual de usuario

Cambo

Cambo Wide DS Digital Series Instrucciones de funcionamiento

Samsung

Samsung SHG-120 Manual de usuario

Ryobi

Ryobi BPL-1820 Manual de operación

Aegis

Aegis ABL-36020P Manual de usuario

Pentax

Pentax Data Back Fc Manual de usuario

Fantasea

Fantasea EyeGrabber F Series Manual de usuario

Honeywell

Honeywell HDZ20HD Manual de usuario

EGO

EGO BA1400T Manual de usuario

Sima

Sima SRW-62 Manual de usuario

Shape

Shape A7SSMKIT Manual de usuario

Slide Kamera

Slide Kamera HST-2 Manual de usuario

Power works

Power works 2902613 Manual de usuario

SES

SES SE-2047-2 Manual de usuario

Olympus

Olympus PT-EP05L Manual de usuario

Starlite

Starlite OctoDome nxt Manual de usuario