AXIOMTEK NA-401 Manual
NA-401
Hardware Installation Guide
For service person only
ii
Disclaimers
The information in this manual has been carefully checked and is believed to be
accurate. AXIOMTEK Co., Ltd. assumes no responsibility for any infringements of
patents or other rights of third parties, which may result from its use.
AXIOMTEK assumes no responsibility for any inaccuracies that may be contained in
this document. AXIOMTEK makes no commitment to update or to keep current the
information contained in this manual.
AXIOMTEK reserves the right to make improvements to this document and/or
product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission ofAXIOMTEK Co.,
Ltd.
Copyright 2005 by AXIOMTEK Co., Ltd.
All rights reserved.
Version A1 November 2005
Printed in Taiwan
iii
Safety Approvals
CE Marking
FCC Class A
FCC Compliance
This equipment has been tested and complies with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with
emission limits.
iv
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist strap
and place all electronic components in any static-shielded
devices. Most electronic components are sensitive to static
electrical charge.
2. Disconnect the power cords from the NA-401 before making any
installation. Be sure both the system and the external devices are
turned OFF. Sudden surge of power could ruin sensitive
components. Make sure the NA-401 is properly grounded.
3. Do not open the system’s top cover. If opening the cover for
maintenance is a must, only a trained technician is allowed to do
so. Integrated circuits on computer boards are sensitive to static
electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
9Before handling a board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. This will help
to discharge any static electricity on your body.
9When handling boards and components, wear a wrist-grounding
strap, available from most electronic component stores.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
Other brand names and trademarks are the properties of their
respective owners.
v
Table of Contents
Chapter 1 Introduciton ------------------------------1
1.1 General Description ..........................................1
1.2 Standard Features.............................................2
1.3 System Specifications ......................................2
1.3.1 Hardware.................................................................2
1.4 Dimensions .......................................................5
1.5 Front Panel Outlets ...........................................6
1.6 Rear Panel Outlets ............................................7
1.7 Indications of Front Panel.................................8
Chapter 2 Installation Procedures------------- 11
2.1 Preinstallation Checklist.................................11
2.2 Setting up the appliance .................................12
2.2.1 Removing and Replacing the Top Cover ............12
2.2.2 Installing a Microprocessor (CPU) 錯誤! 尚未定義書
籤。
2.2.3 Installing a memory module (DIMM)....................17
2.2.4 Installing a DMA/66/100 hard drive......................18
2.2.5 Install a Riser Card.................................................19
2.2.6 Connector and Jumper ......................................23
2.2.7 Install Display Interface.........................................23
2.2.8 Install Serial Port ....................................................23
2.2.9 Installing Keyboard & PS/2 Mouse........................24
2.2.10 Installing USB Connector.......................................24
2.2.11 Installing and Program LCD Module ………………25
Chapter 3 Award BIOS Utility-------------------- 30
3.1 BIOS Introduction ...........................................30
3.2 BIOS Setup......................................................30
3.3 Standard CMOS Setup.....................................31
3.4 Advanced BIOS Features ................................35
3.5 Advanced Chipset Features............................41
3.6 Integrated Peripherals ....................................43
3.7 Power Management Setup...............................47
3.8 PNP/PCI Configuration....................................51
3.9 PC Health Status .............................................54
3.10 Load Optimized Defaults.................................55
3.11 Set Supervisor/User Password .......................55
3.12 Save & Exit Setup............................................58
vi
3.13 Quit Without Saving........................................60
Appendix A Warning ----------------------------- 62
NA-401 Hardware Installation Guide
Introduction 1
Chapter 1
Introduction
This chapter contains the general information and the detailed
specifications of the NA-401 Network Appliance server. Chapter 1
includes the following sections:
General Description Mechanical Dimensions
Features I/O Outlets
System Specifications
1.1 General Description
The NA-401 server is designed for network software solution
providers those have data secure, voice over IP, video streaming,
network bandwidth controller and another networking appliance
requirements across this stable and reliable multiple LAN device.
It is a reliable and affordable, 1U-height unit that requires only power
and network connections for setup. There can be deployed up to four
LAN ports combinations for customer selection in the maximum for
application.
NA-401 has pretty good enclosure management interface to be
implemented in the factory default. It can support P.O.S.T (Power on
Self Test) feature through hyper-terminal by console port. LCD module
function is available for customer coding also.
And it has room space for one hard drive deployment. Customer can
implement system log and monitoring functions through this hardware
specification. With its innovative mechanical and electrical design, the
NA-401 server provides one PCI expansion slot for VPN encryption /
decryption adapter board and another special functions enabling. It cans
NA-401 Hardware Installation Guide
Introduction
2
enhancement network security process performance and of-load the
CPU loading.
The NA-401 can support wonderful networking application platform by
excellent cost with performance ratio.
1.2 Standard Features
z1U-height rack-mount/stacked-up design
zHigh performance Intel Pentium 4 processor
(LGA775-Pin)
zFour gigabit LAN ports (through PCI-Express by one
interface) combinations are for NA-401.
zSupport BIOS redirected to COM port feature
zSupport RS-232 and two USB
zPCI 32-bit/33MHz expansion slot and one Mini-PCI slot
for another network security encryption board
zLCM setting functions is available
zSupports Redhat Linux and Fedora Code III Networks
1.3 System Specifications
1.3.1 Hardware
zForm Factor:
1U rack-mount/stacked-up on desktop design
zCapacity:
It is from 0 to 250GB and beyond, depending on the 3.5” hard
disk drive capacity.
zPower Supply:
Single 300W ATX HRP power supplies
Standard ATX power input connector
zHard Drive:
Spacing for 1 x IDE HDD (3.5”)
zRear Panel Connector:
NA-401 Hardware Installation Guide
Introduction 3
4 x 10/100/1000 Base-T Ethernet LAN port w/LED through
PCI-E by one interface
1 x Console port
2 x USB port
zFront Panel LED:
1 x LED for HDDs
1 x Power LED for System
zProcessor:
IntelPentium4 processor up to 3.6GHz, LGA 775 Pin
FSB 800MHz
zBIOS:
Award 4MB Flash BIOS Plug & Play
zL2 Cache:
Built-in in CPU
zMain Memory:
Four DDR266/DDR333 memory DIMM can be up to 4GB in the
maximum
zIDE Interface:
Support one ATA 66/100/133 EIDE channels
Support four S-ATA 1.0 channels
zSerial Port:
One UART
zEthernet:
Totally has four LAN port connections are available.
zExpansion:
One PCI 32-bit/33MHz and one Mini-PCI 32-bit/33MHz for
security encryption card or other third-party cards expansion
zCompact-FlashTM:
One IDE interface CompactFlashTM socket for embedded use
zDimensions:
427mm(19”)(W) x 44mm(1.75”)(H) x 302mm(11.85”)(D)
zWeight:
Approx. 8.5kg with Power supplies, without any hard drive
zOperation environment:
NA-401 Hardware Installation Guide
Introduction
4
Air temperature: 0° C – 40°C
Humidity: 10% – 95%
zStorage environment:
Air temperature: -20° C – 70°C
Humidity: 10% – 95%
Otros manuales para NA-401
1
Tabla de contenidos
Otros manuales de Servidor de AXIOMTEK
AXIOMTEK
AXIOMTEK NA-810A Manual
AXIOMTEK
AXIOMTEK NA-1301 Manual
AXIOMTEK
AXIOMTEK NA590 Series Manual de usuario
AXIOMTEK
AXIOMTEK NA-814 Manual
AXIOMTEK
AXIOMTEK AX62140TP-P4 Manual de usuario
AXIOMTEK
AXIOMTEK NA-550 Series Manual de usuario
AXIOMTEK
AXIOMTEK NA580 series Manual de usuario
AXIOMTEK
AXIOMTEK NA-320 Series Manual de usuario
AXIOMTEK
AXIOMTEK IRU131 Manual de usuario
AXIOMTEK
AXIOMTEK NA-806D Manual
