Axio MET AX-C850 Instrucciones de montaje
HANDHELD DIGITAL CLAMP
MULTIMETER
AX-C850
OPERATOR’S INSTRUCTION MANUAL
2
Safety Infor ation
To avoid possible electric shock or personal injury:
•Never apply more than 30V between any two jacks, or between any jack and earth ground.
•ake sure the battery door is closed and latched before you operate the calibrator.
•Remove test leads from the calibrator before you open the battery door.
•Do not operate calibrator if it is damaged.
•Do not operate the calibrator around explosive gas, vapor, or dust.
To avoid possible damage the calibrator:
•ake sure choose the right jack and rang, before use the calibrator to measurement or calibrator.
•Take away the calibrator from the used circumstance, before operate the calibrator or after close
the calibrator.
Introduction
RTD Process Calibrator is exactitude measurement and source instrument, it can be use to calibrate
the RTD
*
transmitter (include most impulse transmitter).
RTD Process Calibrator can measure or simulate 7 difference types of RTD (
o
C or
o
F) and measure
or simulate the Resistance. But it could not use to measurement or source at a same time.
The accessories: 2 pair of test lead and alligator clip, 6 *AAA 1.5V battery, user’s manual.
If the Calibrator is broken or short of some accessories, please contact the supplier.
The following table has showed the technical parameter and function of the Calibrator.
Specification
All the specification will under 1 year calibration cycle and temperature between 18~28
o
C,
except addition explain.
Measure (input)/Si ulate (output) Resistance specification.
Range Measure accuracy
4W ± Ω
Si ulate accuracy
± Ω
Ad ie excitation
A
0,00 Ω ~400,00 Ω
0,1
0,15 0,1 ~ 0,5
0,1 0,5 ~ 3,0
400,0 Ω ~ 1500,0 Ω 0,5 0,5 0,05 ~ 0,8
1500,0 Ω ~ 3200,0 Ω
1
1
0,05 ~ 0,4
2
*
RTD Resistance Temperature Detector
3
Admit excitation current only apply on simulate mode. The admit excitation current could be
marked on the OH meter or RTD meter which was connected to the calibrator.
Admit excitation current: 0.2mA ax input voltage: 30V
Measure (input)/Si ulate (output)RTD specification
Mode Range Accuracy
o
C Ad ie
excitation
A
Input 4W Input 2W/3W Output
Pt10 385 -200~800
o
C / -
328~1472
o
F
Nie określana 0,1~3,0
Pt50 385 -200~800
o
C / -
328~1472
o
F
0,7 1,0 0,7 0,1~3,0
Pt100 385 -200~800
o
C / -
328~1472
o
F
0,33 0,5 0,33 0,1~3,0
Pt200 385 -200~250
o
C / -
328~482
o
F
0,2 0,3 0,2 0,1~3,0
250~630
o
C / 482~1166
o
F 0,8 1,6 0,8
Pt500 385 -200~500
o
C / -
328~932
o
F
0,3 0,6 0,3 0,05~0,8
500~630
o
C / 932~1166
o
F 0,4 0,9 0,4
Pt1000 385 -200~100
o
C / -
328~212
o
F
0,2 0,4 0,2 0,05~0,8
100~630
o
C / 212~1166
o
F 0,2 0,5 0,2
Pt100 JIS -200~630
o
C / -
328~1166
o
F
0,3 0,5 0,3 0,1~3,0
Admit excitation current only apply on simulate mode. The admit excitation current be marked on
the OH meter or RTD meter which was connected to the calibrator.
Admit excitation: 0.2mA ax input voltage: 30V
4
General Specifications:
aximum voltage applied between any jack and earth ground or between any tow jack: 30V
Resolution: RTD 0.1
o
C/
o
F Resistance: 0.01/0.1 Ω
Storage temperature: -40
o
C~60
o
C
Operating temperature: -10
o
C~55
o
C
Operating altitude: 3000 meters maximum
Temperature coefficient: ±0.01%/
o
C on 0
o
C~18
o
C and 28
o
C~50
o
C
Relative humidity: 95% up to 30
o
C, 75% up to 40
o
C, 45% up to 50
o
C, 35% up to 55
o
C
Shock: Random 2g, 5Hz to 500Hz
Safety: 1 meter drop test
Power requirements: 6xAAA 1.5V Battery
Size: 205mmx98mmx46mm
Weight: 472 g (include battery)
International Sy bols
Sy bol Meaning
Earth ground
Conform to European Union directives
Refer to his instruction sheet for information about this feature
Battery
Double insulation
Explanation on Front Panel
The front panel is show as in right figure:
1. 4wire input jack (NC on output)
2. 2wire input/output jack
3. 2wire input/output jack
4. 3wire input jack (NC on output)
5. Power key
5
6. RTD mode key
7.
o
C/
o
F key
8. Input/Output key
9. Increase more value key/wire mode select
10. Reduce more value key/wire mode select
11. Increase less value key
12. Reduce less value key
13. Low power indication
14. Output state indication
15. Output state indication
16. Reading value
17. Unit indication
18. ode indication
Operation Instructions
RTD easure ent
1
Press the power key
5
, turn on the calibrator.
2
Press the Input/Output key
8
, when on the input mode.
3
Press RTD mode key
6
, on the measure type you want.
4
Put the RTD or Resistance on the input jack.
5
If you want to measure with 3W/4W mode, press the wire mode select key
9
,
10
to select,
and put the wire to the correspond input Jack.
6
Get the reading value
16
*The number in the , referring to the „Explanation on Front Panel” (Page 4)
6
RTD Si ulate
1
Press the power key
5
, turn on the calibrator
2
Press the input/output key
8
, when on the output mode.
3
Press the RTD mode key
6
, on the measure type you want.
4
Press the adjust value key
9
,
10
,
11
,
12
, to let the value on your need.
5
Put the RTD meter or Resistance meter on the input Jack.
6
If you want to output with 3W/4W mode, put the other wire on the 2wir jack like
the left picture.
7
If you want to change the output value, then press the adjust value key
9
,
10
,
11
,
12
,
or change to other RTD type use the RTD mode key
6
.
*The number in the , referring to the „Explanation on Front Panel” (Page 4)
7
Maintenance
Cleaning
Periodically wipe the case with a damp cloth and detergent; do not use abrasives or solvents.
Calibration
Calibrate your calibrator once a year to ensure that it performs according to its specifications.
Replacing the Battery
Please change the battery when the LCD indicates .
Turn off the power of the Calibrator, when you change the battery, and screw off the breechblock
on the battery cabinet cover, then take off it and instead the fresh AAA 1.5.V battery.
Tabla de contenidos
Otros manuales de Instrumento de medición de Axio MET
Axio MET
Axio MET AX-7250 Manual de usuario
Axio MET
Axio MET AX-5002 Manual de usuario
Axio MET
Axio MET AX-380 Manual de usuario
Axio MET
Axio MET AX-T2200 Manual de usuario
Axio MET
Axio MET AX-6520 Manual de usuario
Axio MET
Axio MET AX-5001 Manual de usuario
Axio MET
Axio MET AX-355 Manual de usuario
Axio MET
Axio MET AX-C800 Manual de usuario
Axio MET
Axio MET AX-7600 Manual de usuario
Axio MET
Axio MET AX-2040 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario