AVLT-Power AVLT-DM24-1 Manual de usuario
AVLT-DM24-1
AP4-0051B
Freestanding Articulating Dual Monitor Stand
for 13”-32” Screen Size
10Kg
22lbs
each
1
UNPACKING INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
Carefully open the carton, remove contents and lay out on cardboard or other protective
surface to avoid damage.
Check package contents against the Supplied Parts List in the next page to assure that
all components were received undamaged. Do not use damaged or defective parts.
Carefully read all instructions before attempting installation.
Install and operate this device with care. Please read this instruction before installation,
and carefully follow all instructions contained herein. Use proper safety equipment during
installation.
Please call a qualified installation contractor for help if you don't understand these direc-
tions or have any doubts about the safety of the installation.
Do not use this product for any purpose or in any configuration not explicitly specified in this
instruction. We hereby disclaims any and all liability for injury or damage arising from incor-
rect assembly, incorrect mounting, or incorrect use of this product.
Thank you for choosing our products!
2
Supplied Parts List
22
(3)M5x14 Bolt-e
(1)M10 Washer-i
(4)Wire Clip-l2
(8)M4x30 Bolt-p
(1)Pole-a
(1)Support Plate-h
(1)Wire Clip-l1
(8)M4x12
Thumb Bolt-o
(2)VESA Plate-d
(1)M10 Bolt-g
(1)Grommet Base
Plate-k
(1)Wrench-n
(1)Soft Pad-r
(1)Swivel Arm-c
(2)Nut-f
(1)Spring Washer-j
(1)Allen Key-m
(8)M4 Spacer-q
(1)Weighted Base-b
3
Step 1 Install the Pole to the Desktop
1. Install the Pole(a) to the Weighted
Base(b) using 3pcs M5x14 Bolts(e),
and tighten using the Allen Key(m), see
Figure 1.
2. Optionally, you can drill a 10mm
diameter hole in your desk and secure
using the Support Plate (h), M10 Wash-
er(i), Spring Washer(j) and M10 Bolt(g).
Fasten the M10 Bolt with provided
Wrench(n), see Figure 2.
Option A: Weighted Base Install
h
g
i
j
a
k
e
Figure 3
Figure 5
Option B: Grommet Base Install
If the existing grommet hole comes with a
plastic protector, remove it to ensure a flat
surface before installing the desk mount.
1.Install the Grommet Base Plate(k) to the
Pole(a) using 3pcs M5x14 Bolts(e), and
tighten using the Allen Key(m), see Figure 3.
2. Attach Soft Pad(r) to the Grommet Base
Plate(k), see Figure 4.
3. Position the Pole(a) on the mounting
surface and secure using the Support Plate
(h), M10 Washer(i), Spring Washer(j) and
M10 Bolt(g). Fasten the M10 Bolt using
provided Wrench(n), see Figure 5.
Existing Grommet Hole Installation
a
e
b
h
g
i
l
j
Figure 2
Figure 1
rFigure 4
Install the Pole to the Desktop
Install Arm to the Pole
Install Swivel Arm(c) to the Pole
(a). Fasten the bolt with supplied
Allen Key(m). Attach the Wire
Clip(l1,l2) to the Pole(a) and
Swivel Arm(c).
h
g
i
j
k
a
e
Figure 6
Figure 8
Option C: Grommet Base Install
1.Position the Pole(a) on the mounting
surface and mark the center hole. Drill a 3/8"
(10mm) diameter hole at the marked posi-
tion through the mounting surface.
2. Install the Grommet Base Plate(k) to the
Pole(a) using 3pcs M5x14 Bolts(e), and
tighten using the Allen Key(m), see Figure 6.
3. Attach Soft Pad(r) to the Grommet Base
Plate(k), see Figure 7.
4. Position the Pole(a) on the mounting
surface and secure using the Support Plate
(h), M10 Washer(i), Spring Washer(j) and
M10 Bolt(g). Fasten the M10 Bolt using
provided Wrench(n), see Figure 8.
Self Drilled Grommet Hole Installation
4
Step 1
Step 2
c
m
l1
l2
rFigure 7
Attach the VESA Plate to the Monitor
5
q
p
f
o
Step 3
Slide the Monitor onto the Head of Swivel Arm
Step 4
For Monitor with Flat Back For Monitor with Curved or
Recessed Back
Slide the monitor onto the head of
Swivel Arm(c) as shown in the above
diagram.
Install the security Nut(f). Make sure the
security nut is installed before you rotate
the monitor.
Tighten the bolt with the supplied Allen
Key(m) to fix the tilt angle.
Use the supplied Allen Key(m) to make the
necessary adjustments.
Manage the wires and store the Allen
keys(m) in Wire Clip(l1) for future use.
If one monitor is lower, remove the Nut(f)
and turn the bolt counter-clockwise with
supplied Allen key(m) to raise the monitor.
Install the Nut(f) after the adjustment.
6
m
Make the Necessary Adjustments
Step 5
Manage the Wires and Store the Allen Keys on Wire Clip
Step 6
Fix the tilt angle Ignore this step if
monitors are level
m
m
l1
Tabla de contenidos
Otros manuales de Rack y soporte de AVLT-Power
AVLT-Power
AVLT-Power AVLT-DM72-1 Manual de usuario
AVLT-Power
AVLT-Power AVLT-MT11-1 Manual de usuario
AVLT-Power
AVLT-Power Non-VESA Monitor Adapter Kit for 13" to 27" LCD/LED Screen... Manual de usuario
AVLT-Power
AVLT-Power Aluminum Laptop Stand Adjustable Notebook Stand for MacBook &PC... Hoja de información del producto
AVLT-Power
AVLT-Power AP4-0029A Hoja de información del producto
AVLT-Power
AVLT-Power AVLT-MT42-1 Manual de usuario
