Avital AMX7 Manual de usuario

Hurricane 2

Installation

Manual

Hurricane2

/AMX78 (2) Installation Manual

TABLE OF CONTENTS

Required Installation Tools .......................2

Important Information..........................2

Wiring Diagram..............................3

14 Pin Connector..............................4

Installation Procedures..........................5

Control Unit................................5

Antenna..................................5

Wireloom..................................5

Impact Sensor...............................5

Valet Switch................................6

LED Indicator...............................6

Ignition Input................................6

Channel 2 Accessory Output........................6

Channel 4 Accessory Output........................6

Parking Lights...............................7

Interior Light Trigger/Illumination.....................7

Starter Disable...............................7

Door Lock/Unlock.............................8

Hood/Trunk Pin Switch..........................8

Siren....................................8

Power and Ground Connections......................9

Door Lock Diagrams.........................10, 11

Programming Alarm System Features.................12

Programming Table for Alarm Features.................12

Adding or Deleting Remote Controls .................13

Programming Table for Remote Controls................13

Hurricane

/AMX78 (2) Installation Manual

Required Installation Tools

Voltmeter

Wire Strippers

Electric Drill & Bits

Phillips Screw Driver

Convoluted Tubing *

Solder Gun *

Wire Crimpers

Shrink Tube *

Electrical Tape* Optional

Important Information

1.Test all circuits with a voltmeter.

2.Make all wiring connections with the supplied solderless crimp

connectors. DO NOT twist wires or use “scotch-lok” connectors.

3.Route RED, RED/WHITE and BLACK wires from the control unit

directly to the battery.

4. Keep extensions as short as possible. Use same gauge wires for short

extensions and larger gauge wires for longer extensions.

5.Before installing, discuss the placement of the LED indicator and valet

switch with the vehicle owner.

6.Make all battery connections by removing the bolts from the cable

clamps. DO NOT disconnect the battery cables.

7. Turn off dome light or remove dome light fuse to prevent battery drain.

8.Making secure connections is a very important part of your installation.

Solderless crimp connectors are supplied in your hardware accessory

package. This type of connection is sufficient for most of your

installation. However, soldering of the starter disable wires is

recommended whenever possible. For a more secure installation, solder

all of your connections and insulate with heat shrink tubing.

This device complies with Part 15 of the FCC rules. Any changes or

modifications made to the system without the express approval of Avital

Technologies, Inc. could void the user's authority to operate this equipment.

Hurricane2

/AMX78 (2) Installation Manual

Wiring Diagram

Hurricane2

/AMX78 (2) Installation Manual

Hurricane2

/AMX78 (2) Installation Manual

14 Pin Connector

Wire ColorDescription

Red/WhiteParking Light Polarity (+) or (-) Select

Red/Black Parking Light Output(s) - 2 Wires for European Models

RedBattery (+)

GrayArmed (-) Output Pre-wired to Starter Disable Relay

Black Battery (-)

Violet Siren (-) Output

TanHood/Trunk (-) Input

White/BlackInterior Light Trigger/Illumination Polarity (+) or (-) Select

Dark BlueChannel 2 Accessory (-) Output

White Door Trigger (+) or (-) Input

PinkIgnition Input Prewired to Starter Disable Relay

Light BlueChannel 4 Accessory (-) Output

Blue/WhiteDoor Lock (-) Output, Door Unlock (+) Output

Green/WhiteDoor Unlock (-) Output, Door Lock (+) Output

Installation Procedures

Control Unit

1.Select a location under the dash that will allow you to use the tie wraps

to securely fasten the control unit.

2.Mount the control unit as high as possible to ensure maximum range.

3.Do not mount the control unit near moving parts.

4.Avoid areas that are in the direct path of air blowing from the vents.

5.Route wires from this point, leaving slack for ease of service.

Antenna

1.Do not shorten or lengthen the antenna.

2.Route the antenna away from the control unit.

3.Keep the antenna as far away from metal and wire harnesses as possible

to optimize range.

Wireloom

1. Plug the wireloom securely into the control unit.

2. Route wires from the control unit directly to each connection point.

3.Separate the RED, RED/WHITE, BLACK, VIOLET and TAN wires.

4.Sleeve the wires with vinyl tubing or electrical tape and route them

through an existing rubber grommet into the engine compartment.

5.If an existing grommet is not available, drill a hole and install a snap

grommet.

Impact Sensor

The sensor must be firmly mounted on a solid metal surface inside the

vehicle. We recommend tie wrapping the sensor to the steering column

housing or steering column support bracket. DO NOT mount the sensor near

moving parts or in the direct path of an air duct opening.

1.Plug the impact sensor BLUE 4 pin connector into the control unit

BLUE 4 pin connector.

2.Route the impact sensor to the chosen mounting location.

3.Using the long tie wraps supplied, securely fasten the impact sensor

allowing access to the adjustment screws.

Hurricane2

/AMX78 (2) Installation Manual

Valet Switch

1.Discuss placement with the owner.

2. Choose a location for the valet switch that is hidden, but convenient for

the owner to access.

3.Drill a ¼" hole and mount the switch.

4. Route the valet switch wires to the control unit.

5.Plug the valet switch WHITE connector into the control unit WHITE

plug.

LED Indicator

1.Discuss placement with the owner.

2. Choose a location that is visible from both sides of the vehicle.

3.Drill a ¼" hole.

4. Route the LED wires through the hole and press LED into place.

5.Route the LED wires to the control unit.

6.Plug the RED LED connector into the control unit RED plug.

Ignition Input

1.Use a voltmeter to locate the one wire that shows +12 volts when the

ignition key is in the "ON," "CRANK" and "RUN" position, and 0 volts

when the ignition key is in the "OFF" position.

2.Connect the control unit PINK wire to the vehicle’s ignition wire.

Channel 2 Accessory Output

The DARK BLUE wire provides a 0.75 second ground (-) output when

activated for 1-2 seconds. If the remote control button is continually pressed,

the signal will stay at ground as long as the button is held. Most trunk

releases are positive and require an optional relay.

Channel 4 Accessory Output

The LIGHT BLUE wire provides a 0.75 second ground output when

activated for 1-2 seconds. If the remote control buttons 1 & 2 are continually

pressed, the signal will stay at ground as long as the buttons are pressed.

This output can be used for optional accessories such as remote start,

window roll-up/down or any other accessory requiring a (-) accessory

activation.

Hurricane2

/AMX78 (2) Installation Manual

Parking Lights

1.If the parking lights are positive trigger, connect the RED/WHITE wire

to the battery positive (+) terminal through the 20 amp fuse.

NOTE: Do not connect the RED/WHITE wire to the control unit RED wire.

2.If the parking lights are negative (-) trigger, connect the RED/WHITE

wire to control unit BLACK wire.

3. Connect the RED/BLACK wire to the vehicle parking light wire.

Interior Light Trigger/Illumination

The system's door trigger will accept a positive or negative door trigger

input. When the alarm is remotely disarmed, the interior lights will turn on

for 30 seconds or until the ignition key is turned on. The WHITE/BLACK

interior light supply wire serves two purposes. It informs the alarm whether

the door trigger polarity is positive or negative switching and provides a

positive or negative supply for interior light illumination.

1.Connect the alarm WHITE wire to the vehicle door trigger wire(s).

2.If the door trigger is negative switching, connect the alarm

WHITE/BLACK wire to ground.

3.If the door trigger wire is positive switching, connect the alarm

WHITE/BLACK wire to a constant fused +12 volt source.

Starter Disable

Make sure the yellow relay wires are solidly connected. The starter circuit

may draw very high current. We recommend that all connections be

soldered.

1.Locate the ignition switch wireloom under the dashboard.

2.Use a voltmeter to find the one wire that will show +12 volts while the

ignition key is in the "CRANKING" cycle only. This should be the

starter solenoid wire.

3. Cut the starter solenoid wire. Test by trying to crank the starter with the

ignition key. If it will not crank, you have the correct wire.

4.Connect one YELLOW wire to the key side.

5.Connect the other YELLOW wire to the starter side.

Hurricane2

/AMX78 (2) Installation Manual

Door Lock/Unlock

CAUTION: Be sure to verify the type of door lock system you are working with.

Some types of door lock systems require optional relays, for example, reverse

polarity type door locks. Refer to the diagrams on pages 10 & 11.

The system can operate both negative and positive door locks. When the

alarm is remotely armed, the BLUE/WHITE wire provides a negative

output. At the same time, the GREEN/WHITE wire provides a 300 MA

positive output. When the alarm is remotely disarmed, the GREEN/WHITE

wire provides a negative output. At the same time the BLUE/WHITE wire

provides a 300 MA positive output.

Hood/Trunk Pin Switch

1.Locate the vehicle hood and/or trunk pin switch that show ground when

the hood or trunk is open only.

2.Connect the alarm module to the vehicle hood and/or trunk pin switch

wire.

3. If the vehicle does not have a hood or trunk pin switch, install an alarm

pin switch and connect it to the alarm module TAN wire.

Siren

1. Choose a location in the engine compartment away from high heat

engine components, moving parts and direct exposure to water.

2.Make sure the siren and siren wires cannot be seen or reached from

below the vehicle.

3.Mount the siren with the two self tapping screws to a solid metal

surface.

4.Connect the siren BLACK wire to the alarm module VIOLET wire.

5.Connect the siren RED wire to the alarm module RED wire.

Hurricane2

/AMX78 (2) Installation Manual

Power and Ground Connections

CAUTION: Do not plug in the system fuses until the final step below.

1.Connect the alarm RED wire to one of the supplied fuse assemblies.

2.Connect the alarm RED/WHITE wire to the other fuse assembly (if the

vehicle parking lights are positive).

3.Connect the fuse assembly(s) to one of the supplied 10mm ring

terminals.

4.Connect the alarm BLACK wire to the other 10mm ring terminal.

5.Remove the (+) and (-) battery bolts. Do not disconnect the battery

clamps.

6. Connect the empty fuse assembly(s) to the positive battery post.

7.Connect the alarm BLACK wire to the battery negative post.

8.Inspect all alarm wiring. Make sure all wires are connected.

9.Install the 5 amp fuse in the alarm module RED wire fuse assembly.

10.Install the 20 amp fuse in the alarm module RED/WHITE fuse

assembly (if the vehicle parking lights are positive).

Hurricane2

/AMX78 (2) Installation Manual

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Alarma de coche de Avital

Avital

Avital Tornado Manual de usuario

Avital

Avital Phoenix 2 Manual de usuario

Avital

Avital AviStar 3300 Manual de usuario

Avital

Avital Point 3 Immobilizer Manual de usuario

Avital

Avital Tornado Manual de usuario

Avital

Avital Hurricane 2 Manual de usuario

Avital

Avital 5103 Manual de usuario

Avital

Avital MAXX2 Manual de usuario

Avital

Avital 4103 Manual de usuario

Avital

Avital 2200 Manual de usuario

Avital

Avital Phoenix 2 Manual de usuario

Avital

Avital Diablo 2 Manual de usuario

Avital

Avital Hurricane 3 Manual de usuario

Avital

Avital Bandido 2 Manual de usuario

Avital

Avital Hurricane Manual de usuario

Avital

Avital Hurricane 3 Manual de usuario

Avital

Avital 4300 Manual de usuario

Avital

Avital 2300 Manual de usuario

Avital

Avital Avistart 4001 Manual de usuario

Avital

Avital AVISTART 6501 Manual de usuario

Avital

Avital AviStart 6500 Manual de usuario

Avital

Avital AVISTART 4000 Manual de usuario

Avital

Avital 4100 Manual de usuario

Avital

Avital AviStart 6001 Manual de usuario

Manuales populares de Alarma de coche de otras marcas

Clifford

Clifford 3606X Manual de usuario

Ultra Start

Ultra Start 2500M SERIES Manual de usuario

Ultra Start

Ultra Start 650 Series Manual de usuario

Audiovox

Audiovox Prestige Platinum+ APS-511C Manual de usuario

Sparkrite

Sparkrite SRA8 Manual de usuario

Viper

Viper 4708V Manual de usuario

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manual

Falcon

Falcon Predator XL3 Guía del usuario

Audiovox

Audiovox Auto Security XR91 Instrucciones de funcionamiento

Clifford

Clifford Sabre II Manual de usuario

CrimeStopper

CrimeStopper CS-8717 Guía de inicio rápido

Ultra Start

Ultra Start 450 SERIES Manual de usuario

Scytek electronic

Scytek electronic Vectra X3 Manual de usuario

Excalibur

Excalibur AL-1860-EDPB Manual de usuario

Clifford

Clifford CYBER 2 Manual de usuario

Gemini

Gemini 7057 Manual de usuario

FlashLogic

FlashLogic FLRSBA PRESTIGE Manual de usuario

Magicar

Magicar FAI-440 Manual de usuario