Aviosys IP Power 9258 DS Manual de usuario
IP Power 9258 DS
User Manual
Firmware Version: 1.0
Date Released: 01/20/2009
- 1 -
Warning:Any changes made to this equipment without permission may cause damages to the
device!
IMPORTANT NOTICE
1. IP Power 9258 DS was designed for indoor use, we carry no responsibility for possible
damages caused by outdoor use, especially in the rain.
2. Please use the power adapter provided by the dealer, we carry no responsibility for the
possible damage from using power adapters not .
4. Do not shake the IP Power 9258 DS in any fashion
5. Please contact the dealer If IP Power 9258 DS is not working properly.
Copyright © 2009 All rights reserved. No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written consent of us.
All trademarks and products mentioned in this document are the properties of us.
- 2 -
Table of Content
1.) WELCOME......................................................................................................5
Introduction.................................................................................................................................................. 5
Minimum System Requirements................................................................................................................. 5
2.) PRODUCT OVERVIEW...................................................................................6
Features......................................................................................................................................................... 6
Specification.................................................................................................................................................. 6
Package Contents ......................................................................................................................................... 7
3.) INTERFACE DESCRIPTION...........................................................................8
Front View..................................................................................................................................................... 8
Rear View...................................................................................................................................................... 9
Rear View.................................................................................................................................................. 9
4.) QUICK START GUIDE..................................................................................10
Quick Hardware Setup.............................................................................................................................. 10
Quick Device Setup .................................................................................................................................... 10
5.) HARDWARE SETUP ....................................................................................11
6.) SOFTWARE SETUP.....................................................................................12
Installing IP Power Software..................................................................................................................... 12
Using IP Edit............................................................................................................................................... 13
IP Service .................................................................................................................................................... 17
7.) HARDWARE INTERFACE............................................................................18
Hardware Reset.......................................................................................................................................... 18
Serial Port Control..................................................................................................................................... 18
How to Replace Fuse.................................................................................................................................. 18
- 3 -
8.) WEB INTERFACE.........................................................................................19
Connection to your Device......................................................................................................................... 19
The Control Console................................................................................................................................... 19
Power Setup ................................................................................................................................................ 20
Power Controls........................................................................................................................................ 20
System Configuration................................................................................................................................. 21
System Setup ........................................................................................................................................... 21
DDNS...................................................................................................................................................... 23
E-mail...................................................................................................................................................... 24
Schedule Ports 1-4 & Ports 5-8................................................................................................................ 25
IP Service................................................................................................................................................. 26
Ping.......................................................................................................................................................... 27
Network Wakeup..................................................................................................................................... 29
Change Password..................................................................................................................................... 29
Firmware Update..................................................................................................................................... 29
Time Change............................................................................................................................................ 30
9.) CONTROLLING THE DEVICE......................................................................31
CGI HTTP Commands.............................................................................................................................. 31
Set Name Command................................................................................................................................31
Get Name Command ............................................................................................................................... 31
Get Firmware Version Command............................................................................................................ 31
Get Time Command ................................................................................................................................32
Set Time Command................................................................................................................................. 32
Set Device Gateway Command............................................................................................................... 32
Set Device DNS Command..................................................................................................................... 33
Turn DHCP ON/OFF............................................................................................................................... 33
View Log Command................................................................................................................................33
Serial Com (RS-232) Control..................................................................................................................... 34
Com1 ....................................................................................................................................................... 34
10.) XML FUNCTIONALITY ...............................................................................36
11.) FREQUENTLY ASKED QUESTIONS (F.A.Q)............................................37
- 4 -
1.) Welcome
Introduction
The IP Power 9258 DS is a state of the art Power Distribution Unit (PDU) & Remote Power
Control (RPC) system. The 9258 DS can be used for various applications including: Power
Management, Server Management, Internet Controllable Timer, System Integration and
much more.
This device allows you to control up to 8 separate devices via the internet. By using a web
browser, you can remotely control the power of the 9258 DS from virtually anywhere.
What makes this device different from other PDU’s is that it has a dual switch design.
Unlike other PDU or RPC units the 9258 DS is completely safe. The dual switch design cuts off
the power and will eliminate any most electrical threats that other systems may have.
Minimum System Requirements
CPU Minimum Requirements
CPU Processor: The same as or above a Intel Pentium III or AMD Athalon
Operating Systems: WINDOWS Operating Systems (IE5.0+SPI) & LINUX
Memory Requirements 64MB or More
Supports Direct Draw Graphics Card
RJ45 LAN & Internet HUB & Switch
Internet (For remote access) or Ethernet Network (Internal Network use) with some type of
Internet connection, (i.e. ADSL, Cable, Dial up or any other forms of Internet service)
- 5 -
2.) Product Overview
Features
1. Dual Switch Design for extra safety and protection
2. HUB function four 4 RJ45 connections
3. Auto-ping (Watch dog) Device Auto Restart / Reboot.
4. Supports: RJ45(HUB), TCP/IP, Http API, Web Server, SMTP Server, DDNS, Log file,
CNT, XML
5. 8 Power control output
6. 2 Main power inputs.
7. 1 RS232 port for System Integration.
8. Design Pressure System: Prevent interference with power noise design. (Second stage
isolation)
9. Scheduler System for date sensitive control
10. Http commands through Internet
11. Log Capability
12. CNT Technology: No Port Forwarding Needed in Router – Just Plug & Play
13. IP Service: Easily Find your device on the internet without having to remember
complicated IP’s
14. Light Aluminum Design
Specification
1. Input Power Voltage: 90-240 VAC
2. Input Frequency: 50/60 Hz full range
3. Dimension: 440x235x40 mm 1.8kg
4. Reliability testing Certification MBTF 200,000 hrs +
5. Operating temperature range: 0 - 50 degrees Celsius.
- 6 -
Package Contents
1.) 9258 DS Unit x 1
2.) 9258 DS Installation CD
3.) Extra Fuse x 1: Located in the
power input of the 9258 Pro
Refer to installing fuse section
4.) RJ45 Cable x 1 (Optional)
5.) Input Power Cable x 2
(Optional)
- 7 -
3.) Interface Description
Front View
Front View
4 Port Ethernet Hub:
Connect up to 4 separate devices with the
built in hub.
1 Serial Ports:
Serial Port 1: Regular Speed
Reset Button:
To reset to original manufacture settings,
hold down the reset button with a pen or a
pin for 15 seconds until will hear a long
beep sound.
Power Status Indicator:
The Power Status indicator
- 8 -
Rear View
Rear View
Rear View
8 Output Power Ports:
Connect up to 8 separate devices that will be
controlled by the 9258 DS. Ports 1-4
2 Input Power Ports:
The input power sends power to the 2 sets o
9258.
2 Power Switch:
The 2 Power switch turns on the input power
Ports 1-4: Switch 1
Ports 5-8 Switch 2
Replaceable Fuse: The 9258 uses a
TYPE：U/C GFE 10A 250V (PF)
- 9 -
4.) Quick Start Guide
Quick Hardware Setup
*Before you plug in the device make sure you have the appropriate input plugs.
* For 220-250V, please use power cable that can support 10A current.
Max Output Current: (total of each four outlets) 10A, (each outlet) 6A.
* For 100-120V, please use power cable that can support 15A current.
Max Output Current: (total of each four outlets) 15A, (each outlet) 6A
1.) Make sure that all the package contents are included, if anything is missing
please contact the store.
2.) Plug the RJ45 (Ethernet Cable) from your router or modem to any of the 4 ports
on the 9258 DS.
3.) Plug in the Input Power Plugs into the device and then into the wall of your
device.
4.) Plug in the devices that you want to control in the output ports of the 9258 DS
Quick Device Setup
Using IPEdit
1.) Click on the REF button, and wait a few seconds. IPEdit will
automatically detect the network settings and setup the device.
2.) Once settings have been detected hit the apply button to apply the new settings.
3.) Hit yes to confirm and Enter the login and password for the Device to Approve
changes
- 10 -
Tabla de contenidos
Otros manuales de Cambiar de Aviosys
