Avigilon NVR5-PRM-2NDCPU Manual de usuario
Avigilon NVR5 Premium 2nd
CPU Kit Installation Guide
Installation Guide
NVR5-PRM-2NDCPU
For
NVR5 PRM 192TB-224TB
1
© 2022,Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, AVIGILON are trademarks
of Avigilon Corporation. Intel is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other
countries. Other names or logos mentioned herein may be the trademarks of their respective owners. The
absence of the symbols ™ and ® in proximity to each trademark in this document or at all is not a disclaimer of
ownership of the related trademark.
This document has been compiled and published using product descriptions and specifications available at
the time of publication. The contents of this document and the specifications of the products discussed
herein are subject to change without notice. Avigilon Corporation reserves the right to make any such
changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the
completeness or accuracy of the information contained in this document; or (2) is responsible for your use of,
or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages
(including consequential damages) caused by reliance on the information presented herein.
Avigilon Corporation
avigilon.com
20220617
2
Introduction
Avigilon provides an optional 2nd CPU kit for the NVR5 Premium. These kits provide all the components
needed to add CPU redundancy to an NVR.
Part Number Description
NVR5-PRM-2NDCPU NVR5 Premium 2nd CPUKit
Confirm Package Contents
Confirm that the kit you are installing contain the following components:
l2nd CPU Kit (NVR5-PRM-2NDCPU):
o1 × Intel Xeon Silver 4216
o1 × CPU heat sink
o1 × processor bracket
o6 × 8 GB - 3200 Mhz DDR4 RDIMMs
o4 × Server I0T 2019 LTSC 4-core license
Recommended Tools
The following tools are not included in the kit package, but are needed to complete the installation:
lPhillips #2 screwdriver
lTorx #T30 screwdriver
lWrist-grounding strap connected to the ground
lESD Mat
Important: It is recommended that you always use an antistatic mat and antistatic strap while
working on components inside the system.
Introduction 4
Installing the NVR5 Premium 2nd CPU Kit
Note: If the NVR5 is an operating part of your security system, be aware that it must be shut down to
complete this procedure.
Before starting to install the kit:
1. Turn off the NVR5, including all attached peripherals. Press the power button on the front panel, and
wait for the light to stop blinking to indicate shutdown is complete.
WARNING — Opening or removing the system cover while the system is powered on may
expose you to a risk of electric shock.
2. Disconnect the NVR5 from the electrical outlet and disconnect the peripherals.
3. Remove all network, power and peripheral cables from the NVR5.
4. If applicable, remove the NVR5 from the rack.
5.
Important: Whenever you need to lift the system, get others to assist you. To avoid injury, do
not attempt to lift the system by yourself.
Installing the NVR5 Premium 2nd CPU Kit 5
Opening the Cover
1. At the top of the NVR5, unlock the latch release then lift and rotate the latch towards the back of the
unit. The cover slides back and is released from the body.
Tip: Use a Phillips #2 screwdriver to remove the shipping screws before unlatching the cover
if you are removing the cover of an NVR5 for the first time.
2. Remove the air shroud by holding it at both ends and lifting it away from the system.
Opening the Cover 6
3. Remove the mid drive tray:
a. Lift the drive tray handles 90 degrees upward.
b. Hold the drive tray handles, and lift the drive tray out of the system.
3. View the interior of the NVR5 and identify the locations where the components of the kit will be
installed.
The view below shows the details of an NVR5 with all of the covers and cards removed, and important
components labeled with numbers.
The components affected by the NVR5 Premium 2nd CPU Kit are:
l4—Memory module
The 6 DIMMs in the kit are installed here.
l5—CPU2 processor and heat sink module socket (with dust cover)
The second CPU in the kit is installed here.
Opening the Cover 7
Note: The other components pointed out in the diagram are not affected by installing the
NVR5 Premium 2nd CPU Kit.
Installing the CPU
You need the processor bracket, processor (CPU), and heatsink provided in the kit to complete this
procedure.
With the NVR5 open and the protective cover removed:
1. Locate the 2nd processor socket and pull off the CPUdust cover with the yellow label over the socket.
2. Unpack the CPU.
3. Place the processor in the processor tray.
Note: Ensure that the pin 1 indicator on the processor tray is aligned with the pin 1 indicator on
the processor.
4. Flex the outer edges of the processor bracket and ensure that the processor is locked into the clips on
the bracket.
Note: Ensure that the pin 1 indicator on the bracket is aligned with the pin 1 indicator on the
processor before placing the bracket.
5. Unpack the heatsink. Be careful not to touch the thermal paste that is pre-applied to the bottom of the
heatsink.
6. Place the heat sink on the processor and push down on the base of the heat sink until the bracket
locks onto the heat sink.
Installing the CPU 8
Important: To avoid damaging the fins on the heat sink, do not press down on the heat sink
fins.
lEnsure that the 2 guide pin holes on the bracket match the guide holes on the heat sink.
lEnsure that the pin 1 indicator on the heat sink (circled red in the image below) is aligned with
the pin 1 indicator on the bracket before placing the heat sink onto the processor and bracket.
7. Align the pin 1 indicator on the heat sink to the system board and then place the processor and heat
sink module on the processor socket.
Important: Ensure that the processor and heat sink module is held parallel to the system
board to prevent damaging the components.
8. Push the blue retention clips inward to allow the heat sink to drop into place.
Installing the CPU 9
Important: Do not force the processor into the socket. The processor should slide easily into
the socket when aligned correctly.
9. Use the star-shaped screwdriver #T30 to tighten the screws on the heat sink in the following order:
a. Partially tighten the first screw (approximately 3 turns).
b. Tighten the second screw completely.
c. Return to the first screw and tighten it completely.
Important: Do not over-tighten or strip the screws.
If the processor and heat sink module slips off the blue retention clips when the screws are partially
tightened, follow these steps to secure the module:
a. Completely loosen both of the heat sink screws.
b. Lower the processor and heat sink module on to the blue retention clips, following the
procedure as described in step 8 above.
c. Secure the processor and heat sink module to the system board, following the instructions as
described in step 9 above.
Installing the CPU 10
Tabla de contenidos
Otros manuales de Hardware de red de Avigilon
Avigilon
Avigilon NVR5-RAM-16GB-A Manual de usuario
Avigilon
Avigilon VMA-AS1-8P Manual de usuario
Avigilon
Avigilon NVR5 PRM FIPS Manual de usuario
Avigilon
Avigilon VMA-AS1-16P Manual de usuario
Avigilon
Avigilon VMA-AIA1-CG1-UPGK Manual de usuario
Avigilon
Avigilon Rialto Manual de instrucciones
Avigilon
Avigilon HD-NVR3-PRM-48TB Manual de usuario
Avigilon
Avigilon Premium NVR5 Series Manual de usuario
Avigilon
Avigilon NVR5-STD-10GBE Manual de usuario
Avigilon
Avigilon Premium NVR5 Series Manual de usuario
Avigilon
Avigilon HD-NVR3-STD-24TB Manual de usuario
Avigilon
Avigilon Premium NVR5 Series Manual de usuario
Avigilon
Avigilon NVR4-VAL-6TB Manual de usuario
Avigilon
Avigilon HD-NVRWS3-8TB Manual de usuario
Avigilon
Avigilon Premium NVR5 Series Manual de usuario
Avigilon
Avigilon Premium NVR5 Series Manual de usuario
Avigilon
Avigilon Premium NVR5 Series Manual de usuario
Avigilon
Avigilon HD-NVR4-PRM-64TB Manual de usuario
Avigilon
Avigilon 3 Series Manual de usuario
Avigilon
Avigilon NVR5-10GBASET-A2 Manual de usuario
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
