Avaya G430 Manual de usuario

Avaya - Proprietary. Use pursuant to the terms of your signed agreement or Avaya policy.

DRAFT - January 25, 2009 - 1:38 PM

Quick Start for Hardware

Installation:

Avaya G430 Media Gateway

03-603236

Issue 1

May 2009

Avaya - Proprietary. Use pursuant to the terms of your signed agreement or Avaya policy.

DRAFT - January 25, 2009 - 1:38 PM

Notice

While reasonable efforts were made to ensure that the information in this

document was complete and accurate at the time of printing, Avaya Inc. can

assume no liability for any errors. Changes and corrections to the information

in this document may be incorporated in future releases.

For full support information, please see the complete document,

Avaya Support Notices for Hardware Documentation, document number

03-600759.

To locate this document on our Web site, simply go to

http://www.avaya.com/support and search for the document number in

the search box.

Documentation disclaimer

Avaya Inc. is not responsible for any modifications, additions, or deletions to

the original published version of this documentation unless such modifications,

additions, or deletions were performed by Avaya. Customer and/or End User

agree to indemnify and hold harmless Avaya, Avaya's agents, servants and

employees against all claims, lawsuits, demands and judgments arising out of,

or in connection with, subsequent modifications, additions or deletions to this

documentation to the extent made by the Customer or End User.

Link disclaimer

Avaya Inc. is not responsible for the contents or reliability of any linked Web

sites referenced elsewhere within this documentation, and Avaya does not

necessarily endorse the products, services, or information described or offered

within them. We cannot guarantee that these links will work all of the time and

we have no control over the availability of the linked pages.

Warranty

Avaya Inc. provides a limited warranty on this product. Refer to your sales

agreement to establish the terms of the limited warranty. In addition, Avaya’s

standard warranty language, as well as information regarding support for this

product, while under warranty, is available through the following Web site:

http://www.avaya.com/support.

Except where expressly stated otherwise, the Product is protected by copyright

and other laws respecting proprietary rights. Unauthorized reproduction,

transfer, and or use can be a criminal, as well as a civil, offense under the

applicable law.

Avaya support

Avaya provides a telephone number for you to use to report problems or to ask

questions about your product. The support telephone number

is 1-800-242-2121 in the United States. For additional support telephone

numbers, see the Avaya Web site: http://www.avaya.com/support.

Issue 1 May 2009 3

Avaya - Proprietary. Use pursuant to the terms of your signed agreement or Avaya policy.

DRAFT - January 25, 2009 - 1:38 PM

Chapter 1: Before you Start

Before you install your Avaya G430 Media Gateway, prepare all the information, resources, and tools that

you need during the installation process.

Preparing the Pre-Installation Worksheet

The Electronic Pre-installation Worksheet (EPW) is a customized Excel spreadsheet that you can use to

collect configuration information. The EPW verifies that you have a complete set of installation information.

Once filled out by the customer and project manager, the EPW can be loaded directly into the Avaya

Installation Wizard (IW) or Gateway Installation Wizard (GIW) for configuration. The EPW should be

completed before the installation. Download the latest version of the EPW spreadsheet from the Avaya Web

site at http://support.avaya.com/avayaiw.

Preparing Contacts you might need

Ensure that you have the names and phone numbers of any people you might need to contact at the

installation site. This list might include the people responsible for network architecture, system

administration, site security, site deliveries, etc.

Preparing Installation Files

Ensure that you load the latest versions of all firmware files for the G430, S8300, and media modules onto

your laptop before configuration. If you install a G430 without an S8300 Server, the configuration process

prompts you for the filenames of all firmware files needed. You can download the firmware files needed for

your installation from the Avaya Support Web site, at http://support.avaya.com.

Preparing the G430 Serial Number

In order to register the gateway to CM, you need the serial number of the G430. The serial number is printed

on a sticker on the back of the G430 chassis.

Obtaining RFA access

You need to obtain a personal Single Sign-On (SSO) for Remote Feature Activation (RFA) web site

authentication login before going to the site for installation. You must complete the authentication process

before you can be assigned an SSO authentication login.

Before you Start

4 Quick Start for Hardware Installation: Avaya G430 Media Gateway

Avaya - Proprietary. Use pursuant to the terms of your signed agreement or Avaya policy.

DRAFT - January 25, 2009 - 1:38 PM

As a first-time user:

●Business Partners should point their browsers to the Business Partner portal option sales_market,

services-voice, training tools and procedures to select RFA.

●Associates should point their browsers to the Avaya Associate portal.

●Contractors should point their browsers to Avaya.com.

●Alternatively go directly to http://rfa.avaya.com.

From that point, log into SSO and complete the process to obtain your personal login.

Downloading CM license and authentication files to your laptop

If you are installing a G430 with an S8300 Server as a primary controller, you need license and

authentication files for the Communication Manager.

1. Create a directory on your laptop for storing license and authentication files.

2. Access the Internet from your laptop and go to rfa.avaya.com.

3. Login using your SSO login and password. The AFS and RFA information home page appears.

4. Start the RFA application from the RFA information page. To create and download the license file and

authentication file, follow the instructions outlined in the Avaya Remote Feature Activation (RFA) User

Guide, 03-300149.

5. Use the download or e-mail capabilities of the RFA web site to download the license and

authentication files to your laptop.

Preparing the INADS IP address

The INADS IP address is required in order to configure the S8300’s modem for alarming. If you are

preparing a G430 with an S8300 for a remote installation, you must first obtain an INADS IP address. Use

the Automatic Registration Tool (ART) to obtain an IP address for an INADS alarming modem.

1. Access the ART Web site on your laptop at http://art.dr.avaya.com.

2. Select Administer S8x00 Server products for installation script, and then log in.

3. Enter the customer information, select Installation Script, and click Start Installation script & IP

Addr Admin. A script file is created and downloaded or e-mailed to you.

Preparing Needed Hardware

●Laptop – to configure the Avaya G430 Media Gateway, you need to prepare a laptop with a serial port.

The laptop must have Internet Explorer installed. If you install a G430 without an S8300, you must

prepare the laptop with a Windows 2000 or Windows XP operating system and a TFTP server.

Preparing Tools Needed for Mounting

Issue 1 May 2009 5

Avaya - Proprietary. Use pursuant to the terms of your signed agreement or Avaya policy.

DRAFT - January 25, 2009 - 1:38 PM

●Modem – in order to set up a remote configuration of the G430, you must prepare a USB modem.

Currently, the G430 supports the MultiTech USB modem, model MT5634ZBA-USB-V92.

Preparing Tools Needed for Mounting

To mount on a rack or wall, prepare a Phillips head screwdriver.

To mount on a wall prepare also:

●415 x 465 mm (16.5 in. x 18.5 in.) plywood board 20 mm (7/8 in.) thick

●Wood screws

●Screws to fasten the G430 to the wall

You might also need wire cutters to attach the grounding conductors, if your site uses a ground block.

Choosing the Installation Site

Ensure that the location where you install your G430 fulfills the following requirements:

●Cables are away from sources of electrical noise such as radio transmitters, broadcast amplifiers,

power lines, fluorescent light fixtures

●Water or moisture cannot enter the case of the chassis.

●Air can flow freely around all sides of the chassis.

●The vents on the sides of the case are not blocked.

●The installation is no more than 25 feet (7.6 m) from an approved ground.

Note:

Note: If the G430 is more than 25 feet (7.6 m) away from an approved ground, you must contact a

licensed electrician to install a supplementary ground conductor.

●The environmental conditions match the following requirements:

●Ambient temperature – 32oto 104oF (0oto 40oC)

●Relative humidity – 10-90% relative humidity

●Minimum clearance for ventilation – 18 in. (45 cm)

●Weight support – 22.5-35 lbs (10-16 kg)

Before you Start

6 Quick Start for Hardware Installation: Avaya G430 Media Gateway

Avaya - Proprietary. Use pursuant to the terms of your signed agreement or Avaya policy.

DRAFT - January 25, 2009 - 1:38 PM

Issue 1 May 2009 7

Avaya - Proprietary. Use pursuant to the terms of your signed agreement or Avaya policy.

DRAFT - January 25, 2009 - 1:37 PM

Chapter 2: Unpack the Device

!CAUTION:

CAUTION: Wear an anti-static wrist ground strap whenever you handle components of a G430 Media

Gateway or EM200. Connect the strap to an approved ground, such as an unpainted metal

surface.

Equipment

For the G430 package and for each EM200 package, if ordered:

Open the box that contains the device, and ensure that it contains the following components and

accessories:

●One device chassis. The required media modules may be installed.

●An Accessory Kit (see Table 1). The EM200 Accessory kit contains the same items as the G430

Accessory kit, as well as an expansion cable for connecting the EM200 to the G430.

Table 1: G430 Accessory Kit

Nine 4-40 Flat Head Screws One Grounding Cable Assembly Four Rubber Standoffs

Unpack the Device

8 Quick Start for Hardware Installation: Avaya G430 Media Gateway

Avaya - Proprietary. Use pursuant to the terms of your signed agreement or Avaya policy.

DRAFT - January 25, 2009 - 1:37 PM

Other Components

The Avaya Partner Contact Closure adjunct box, if ordered, is packaged separately.

If you ordered an upgrade memory kit or an add-on VoIP module, refer to Job Aid: Replacing the Field

Replaceable Units (FRUs) for the Avaya G430 Media Gateway, 03-603237 for installation instructions.

Two 19 in. Rack mount brackets One Cable Management

Assembly Two wall mount brackets

Table 1: G430 Accessory Kit (continued)

Issue 1 May 2009 9

Avaya - Proprietary. Use pursuant to the terms of your signed agreement or Avaya policy.

DRAFT - January 25, 2009 - 1:38 PM

Chapter 3: Mount the Devices

You can position the G430 – and EM200s, if ordered – on a suitable table, or mount them in a rack or on the

wall.The EM200s enable you to optionally extend the G430 by attaching one or two EM200 expansion

modules to the G430. Since the cables attaching the EM200 expansion modules to the G430 are short, you

must install the G430 and EM200s directly above or below each other, in any order.

Keep in mind the following:

●If you are mounting the G430 and EM200 module(s) on a wall, place them on a shelf affixed to the

wall, in addition to following all the wall mounting instructions.

●If you are mounting the G430 and EM200 module(s) on a table, affix the rubber legs to the

bottom-most unit, and place the other unit(s) directly on top.

●If you are mounting on a table or a wall, always place the G430 on top of the EM200(s). This enables

easy access in case you need to open the G430 cover in order to add or replace a DSP module or the

RAM board.

Note:

Note: Although the figures illustrating the mounting instructions depict a G430, all mounting

procedures apply equally to both the G430 and the EM200.

Positioning on a Table

To install a G430 or EM200 as a tabletop unit:

1. Remove the four rubber standoffs from their package.

2. Turn the device upside down.

3. Position each standoff into one of the mounting sites, near each corner of the chassis.

Mounting in a Rack

You can fasten the G430 or EM200 to a standard 19-inch rack either at the front of the device or at its

middle. Before you mount the device, attach the mounting brackets to the device.

Front Mounting Bracket Placement

Attach a regular mounting bracket to one side of the device, near the front, as shown in Figure 1: Front

mounting bracket placement on page 10. Attach a mounting bracket with cable guides to the other side of

the device, as shown in to Figure 3: Attaching a mounting bracket with cable guides on page 10.

Mount the Devices

10 Quick Start for Hardware Installation: Avaya G430 Media Gateway

Avaya - Proprietary. Use pursuant to the terms of your signed agreement or Avaya policy.

DRAFT - January 25, 2009 - 1:38 PM

Middle Mounting Bracket Placement

Attach regular mounting brackets to both sides of the device, as shown in Figure 2: Middle mounting

bracket placement on page 10. You can also attach a mounting bracket with cable guides on one side of the

device, as shown in Figure 3: Attaching a mounting bracket with cable guides on page 10.

Figure 1: Front mounting bracket placement

Figure 2: Middle mounting bracket placement

Figure 3: Attaching a mounting bracket with cable guides

Attaching Mounting Brackets

Follow these steps to attach the mounting brackets:

1. Position a bracket over the holes in the chassis in the desired mounting position.

2. Affix the bracket to the chassis with three flat head 4-40 screws.

3. Tighten the screws with the screwdriver.

Otros manuales para G430

Tabla de contenidos

Otros manuales de Puerta de Avaya

Avaya

Avaya BSGX4e Manual de usuario

Avaya

Avaya G700 Instrucciones de funcionamiento y seguridad

Avaya

Avaya IG550 Manual de instrucciones

Avaya

Avaya G250 Series Manual de usuario

$Avaya S\G203 Manual$

Avaya

Avaya S\G203 Manual

Avaya

Avaya IG550 Manual de usuario

Avaya

Avaya W310 Manual de usuario

Avaya

Avaya G860 Diagrama de cableado

Avaya

Avaya G450 Manager Manual de instrucciones

Avaya

Avaya G450 Manager Manual de usuario

Avaya

Avaya Remote Gateway 911 Series Manual de usuario

Avaya

Avaya G650 Manual de usuario

Avaya

Avaya SG5 Manual de usuario

Avaya

Avaya G700 Manual de instrucciones

Avaya

Avaya Advanced Gateway 2330 Manual del propietario

Avaya

Avaya CMC1 Guía de inicio rápido

Avaya

Avaya MCC1 Manual

Avaya

Avaya G430 Manual de usuario

Avaya

Avaya Media Gateway G350 Manual de usuario

Avaya

Avaya CMC1 Guía de inicio rápido

Avaya

Avaya Media Gateway G250 Manual de instalación y operación

Avaya

Avaya CMC1 Manual de usuario

Avaya

Avaya G450 Manager Manual de usuario

Avaya

Avaya Media Gateway G250 Manual de usuario

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario