Avalue Technology ECM-945GSE Manual de usuario

Part No. E2017381602R

ECM-945GSE

Intel® Atom™ processor N270 3.5” Micro Module with Intel®

945GSE + ICH7-M Chipset

Quick Installation Guide

3rd Ed – 06 November 2009

ECM-945GSE Quick Installation Guide

2 ECM-945GSE Quick Installation Guide

1. Getting Started

1.1 Safety Precautions

Warning!

Always completely disconnect the power cord from your

chassis whenever you work with the hardware. Do not

make connections while the power is on. Sensitive

electronic components can be damaged by sudden power

surges. Only experienced electronics personnel should

open the PC chassis.

Caution!

Always ground yourself to remove any static charge before

touching the CPU card. Modern electronic devices are very

sensitive to static electric charges. As a safety precaution,

use a grounding wrist strap at all times. Place all electronic

components in a static-dissipative surface or static-shielded

bag when they are not in the chassis.

Always note that improper disassembling action could cause damage to the

motherboard. We suggest not removing the heatsink without correct

instructions in any circumstance. If you really have to do this, please contact

us for further support.

1.2 Packing List

Before you begin installing your single board, please make sure that the

following materials have been shipped:

z1 x Intel® 945GSE Micro Module

z1 x Quick Installation Guide for ECM-945GSE

z1 x AUX-021 daughter board

z1 x DVD-ROM contains the followings:

—User’s Manual (this manual in PDF file)

—Ethernet driver and utilities

—VGA drivers and utilities

—Audio drivers and utilities

z1 x Cable set contains the followings:

—1 x IDE HDD cable (44-pin, pitch 2.0mm)

—1 x Audio cable (10pin, 2.0mm pitch)

—1 x USB cable (10P/2.54mm-10P/2.0mm)

—1 x Serial ATA cables (7-pin, standard)

—1 x PS/2 Keyboard & mouse Y cable

Quick Installation Guide

ECM-945GSE Quick Installation Guide

2. Hardware

Configuration

ECM-945GSE Quick Installation Guide

4 ECM-945GSE Quick Installation Guide

2.1 Product Overview

Quick Installation Guide

ECM-945GSE Quick Installation Guide

2.2 Jumper and Connector List

You can configure your board to match the needs of your application by setting jumpers. A

jumper is the simplest kind of electric switch.

It consists of two metal pins and a small metal clip (often protected by a plastic cover) that

slides over the pins to connect them. To “close” a jumper you connect the pins with the clip.

To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1,

2, and 3. In this case, you would connect either two pins.

The jumper settings are schematically depicted in this manual as follows:

A pair of needle-nose pliers may be helpful when working with jumpers.

Connectors on the board are linked to external devices such as hard disk drives, a

keyboard, or floppy drives. In addition, the board has a number of jumpers that allow you to

configure your system to suit your application.

If you have any doubts about the best hardware configuration for your application, contact

your local distributor or sales representative before you make any changes.

The following tables list the function of each of the board’s jumpers and connectors.

Jumpers

Label Function Note

JBAT1 Clear CMOS 3 x 1 header, pitch 2.54mm

JCF CF mode select 3 x 1 header, pitch 2.54mm

PWR_MSEL AT/ATX mode select 2 x 1 header, pitch 2.0mm

PWR_5VSEL Input Power type select 3 x 1 header, pitch 2.54mm

ECM-945GSE Quick Installation Guide

6 ECM-945GSE Quick Installation Guide

Connectors

Label Function Note

CFCARD Compact Flash card connector Type I/II x 1

COM1 Serial port 1 connector D-sub 9-pin, male

CPU_FAN CPU fan connector 3 x 1 wafer, pitch 2.54mm

IDE Primary IDE connector 22x2 header, pitch 2.0mm

J422/485 Serial port 2 in RS422/485 mode 3 x 2 header, pitch 2.0mm

JAUDIO Audio connector 5 x 2 header, pitch 2.0mm

JBKL LCD Inverter Connector 5 x 1 wafer, pitch 2.0mm

JCOM2 Serial port 2 in RS232 mode 5 x 2 header, pitch 2.0mm

JDIO General purpose I/O connector 10 x 2 header, pitch 2.0mm

JDVI DVI connector

JKB/MS PS/2 keyboard & mouse connector 4 x 2 header, pitch 2.0mm

JLPC (Reserved for debug) 5 x 2 header, pitch 2.0mm

JLVDS LVDS connector

JPWRBTN Power button connector

JSPI (Revered for BIOS programming)

JTV TV connector 3 x 2 header, pitch 2.0mm

JUSB2 USB connector 2 & 3 5 x 2 header, pitch 2.0mm

JUSB3 USB connector 4 & 5 5 x 2 header, pitch 2.0mm

JVR LCD backlight brightness adjustment 3 x 1 header, pitch 2.54mm

LED1 HDD & Power indicator

PWR_SB 5VSB connector in ATX 3 x 1 wafer, pitch 2.54mm

PWRCON Power connector 2 x 2 header, pitch 2.0mm

RSTBTN Reset button

SATA1 Serial ATA connector 1

SATA2 Serial ATA connector 2

USB1 USB connector 0 & 1

(Co-lay with KB/MS )

VGA VGA connector D-sub 15-pin, female

Quick Installation Guide

ECM-945GSE Quick Installation Guide

2.3 Setting Jumpers & Connectors

2.3.1 AT/ATX mode select (PWR_MSEL)

* Default

PWR_MSEL

AT*

ATX

JPWRBTN

Signal PIN

GND 2

PWR_BT 1

Note: JPWRBTN is available in ATX

mode.

PWR_M

JPWRBTN

ECM-945GSE Quick Installation Guide

8 ECM-945GSE Quick Installation Guide

2.3.2 Input Power type select (PWR_5VSEL)

* Default

AT Type *

ATX Type

2.3.3 5VSB Power connector in ATX Type (PWR_SB)

PIN Signal

1PSON#

2GND

35VSB

Note: Connect PWR_SB with cable in

ATX type power-input.

Quick Installation Guide

ECM-945GSE Quick Installation Guide

2.3.3.1 Signal Description –AT/ATX mode & Input power type

Input power type Power-ON Mode Description

AT Mode

(PWR_MSEL)

Use AT type power input, and set

the board in AT mode.

AT type

(PWR_5VSEL)

ATX Mode

(PWR_MSEL)

Use AT type power input, and set

the board in ATX mode.

AT Mode

(PWR_MSEL)

Use ATX type power input, and set

the board in AT mode.

ATX type

(PWR_5VSEL)

ATX Mode

(PWR_MSEL)

Use ATX type power input, and set

the board in ATX mode.

ECM-945GSE Quick Installation Guide

10 ECM-945GSE Quick Installation Guide

2.3.4 Clear CMOS (JBAT)

* Default

Protect*

Clear CMOS

2.3.5 CF Mode select (JCF)

* Default

Master*

Slave

Otros manuales para ECM-945GSE

Tabla de contenidos

Otros manuales de Hardware de computadora de Avalue Technology

Avalue Technology

Avalue Technology REN-WHLPC Manual de usuario

Avalue Technology

Avalue Technology BRX-P501-H110 Manual de usuario

Avalue Technology

Avalue Technology VMS-BYT Manual de usuario

Avalue Technology

Avalue Technology ECM-945GSE Manual de usuario

Avalue Technology

Avalue Technology RSC-IMX8M Manual de usuario

Avalue Technology

Avalue Technology EMX-BYT2-B1 Manual de usuario

Avalue Technology

Avalue Technology BAX-P501-C236 Manual de usuario

Avalue Technology

Avalue Technology CAXA0-DC Manual de usuario

Avalue Technology

Avalue Technology EZX-EHLP Manual de usuario

Avalue Technology

Avalue Technology EAX-R680P Manual de usuario

Avalue Technology

Avalue Technology BAX-P501-Q170 Manual de usuario

Avalue Technology

Avalue Technology EMS-CDV Manual de usuario

Avalue Technology

Avalue Technology EMS-EHL Manual de usuario

Avalue Technology

Avalue Technology EPC-TGU-B1 Manual de usuario

Avalue Technology

Avalue Technology BMX-T550 Manual de usuario

Avalue Technology

Avalue Technology EMX-H610P Manual de usuario

Avalue Technology

Avalue Technology ECM-BYT2 Manual de usuario

Avalue Technology

Avalue Technology SPC-2133-B1 Manual de usuario

Avalue Technology

Avalue Technology ECM-TGUC Manual de usuario

Avalue Technology

Avalue Technology EMX-R680P Manual de usuario

Avalue Technology

Avalue Technology BMX-T540 Manual de usuario

Avalue Technology

Avalue Technology EMX-H110KP-B1 Manual de usuario

Avalue Technology

Avalue Technology ENX-LX800 Manual de usuario

Avalue Technology

Avalue Technology EMX-Q170KP-B1 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario