AUTOTERM COMFORT BOILER CONTROL Manual de usuario

10.2023 - v1.0

Manufacturer: AUTOTERM LLC

Paleju 72, Marupe, Latvia, LV-2167

Warranty Department warranty@autoterm.com

Technical Support service@autoterm.com

www.autoterm.com

COMFORT BOILER

CONTROL

User’s manual

CONTENTS

INTRODUCTION ............................................................................................................................... 3

SAFETY INSTRUCTIONS .................................................................................................................... 3

LIABILITY .......................................................................................................................................... 4

1. GENERAL INFORMATION ......................................................................................................... 5

1.1. DISPLAY ........................................................................................................................... 5

1.2. ROTARY KNOB ................................................................................................................. 6

1.3. BACK BUTTON ................................................................................................................. 6

1.4. QUICK BUTTON ............................................................................................................... 6

1.5. LED INDICATORS ............................................................................................................. 6

2. MOUNTING AND CONNECTION ............................................................................................... 7

3. OPERATION AND SETTINGS ..................................................................................................... 8

3.1. MAIN MENU .................................................................................................................... 8

3.2. TIMERS ............................................................................................................................ 8

3.3. HEATING ....................................................................................................................... 10

3.4. VENTILATION ................................................................................................................ 12

4. SETTINGS ................................................................................................................................ 13

4.1. TIME/DATE .................................................................................................................... 13

4.2. DISPLAY ......................................................................................................................... 13

4.3. HEATER ........................................................................................................................ 13

4.4. BOILER .......................................................................................................................... 14

4.5. LED ............................................................................................................................... 14

5. ERRORS AND MAINTANACE .................................................................................................. 15

4.6. RESET ........................................................................................................................... 14

In case of questions about compatibility with older products please contact Your local

dealer or AUTOTERM Service center.

In case of any problems, we strongly recommend contacting certified service centers. Contact

information and the location of certified service centers can be found on our website

www.autoterm.com.

Please read carefully this manual before operating the AUTOTERM heaters.

This manual contains needful information in order to use this product correctly.

Disregarding of these instructions can void the warranty of the product, lead to

damage of product and/or property and be a risk to health.

If the heater /boiler is handled and/or installed improperly, there is a possibility of a

fire hazard and damage of property because fuel/electrical and hot water

components are being used. That is why all safety precautions, operation and

installation instructions must be observed.

For other languages of this manual, please visit www.autoterm.com/manuals.

SAFETY INSTRUCTIONS

Risk to health and/or damage of product

-The heater may only be used for the purposes specified in its respective operation manual.

-DO NOT use the heater in closed and/or poorly ventilated places (e.g. garage, workshop,

etc.) - Do not step on the heater or put any objects on it and in it.

-Do not put any body parts or items in to any of the air inlets or outlets of the heater. - For

air heaters. Do not allow hot air to be blown directly at people, animals or heat sensitive

objects.

-To avoid burns, do not touch the exhaust lines and the heater while it is operating.

-Caution: combiBOIL can heat water to up to 85°C (depending on the heating method).

-Direct un-mixed of domestic water can result in serious burns. Use a scald protection/pre-

mixing valve (recommended!) or set an appropriate target temperature on the Comfort

Boiler Control panel.

INTRODUCTION

Dear Customer!

Thank You for choosing the control panel AUTOTERM Comfort Boiler Control! We are doing

everything to make this product meet Your requirements, so its quality satisfies every customer.

Comfort Boiler Control is designed to be intuitive and comfortable to use, to ensure the best

experience when it comes to controlling Your climate and domestic water temperature.

The Comfort Boiler Control comes with a 5m long temperature probe specially designed for

AUTOTERM combiBOIL boiler.

AUTOTERM Comfort Boiler Control is compatible with all AUTOTERM AIR Series heaters.

Some older versions of AIR heaters may not support some of the functions.

Risk of fire and explosion

-The heater is not designed for installation and use on any type of ADR transportation vehicle.

-When refueling heater must be shut down. Note: the shutdown process can take up

to 10 minutes.

-The vehicle where the heater is installed must be equipped with a fire extinguisher.

-Do not cover the heater with clothing, pieces of fabric and so on, and do not place such

objects in front of the air intake pipe or inlet and output of the heated air.

-Do not use or install the heater in places, where flammable vapors or gases or large amounts

of dust may form and accumulate.

-Do not use or install the heater in places, where flammable and/or explosive items or

substances are stored.

-Avoid contact with any flammable objects with the heater’s exhaust pipe.

Risk of damage due electrical nature

-Do not connect/disconnect any wiring of the heater while it is connected to the power supply

or operating.

-Do not connect the heater to the power circuit of the vessel, when the engine is operating

and there is no battery.

-The heater can be switched on again 15-20 seconds after disabling indications on the control

panel, which means that the heater has shut down.

-The length of the control panel wiring cannot exceed 15 meters.

Personnel certified by AUTOTERM is needed

-In case of faults in the operation of the heater, contact specialized repair organizations

authorized by AUTOTERM.

LIABILITY

The manufacturer is not liable for any damage as a result of installation and repairs by

uncertified personnel and/or use of third-party parts and accessories without the

approval of the manufacturer.

In case of any problems, we strongly recommend contacting certified service centers. Contact

information and location of certified service centers can be found on our website

www.autoterm.com.

1. GENERAL INFORMATION

1. DISPLAY

3. BACK BUTTON

5. LED INDICATORS

2. ROTARY KNOB

4. QUICK BUTTON

1.1. DISPLAY

•While in sleep mode:

odisplay is inactive;

oscreensaver shows:

─temperature;

─current time and date;

─symbol of set operation mode, if active.

─ water temperature

─ frost protection

Control panel goes in to sleep mode after the time of inactivity set in

display settings.

Sleep mode is canceled by pressing the knob or the back button.

•While active display shows:

ocurrent time;

opower supply voltage;

otemperature;

oset operation mode, if active;

oactive timers;

owater temperature;

ofrost protection, if active

To access the main screen control panel has to be woken from sleep

mode.

For air heater temperature displayed depends on the temperature sensor selected.

Description of each symbol and screen layouts can be found in their respective sections

of the manual.

When an operation mode is active, the respective symbol is displayed on the main screen

(under the current time) and it works as a quick menu. By rotating the knob three options can

be accessed:

•Active operation mode

settings

•Shut off the heater

•Access the main menu

Confirm selection by pressing the knob.

1.2. ROTARY KNOB

The rotary knob is the main button for navigation through the interface.

•When control panel is active pressing the knob enters the main menu. After that pressing

the knob confirms selected item or setting.

•Turning right selects next item or increases value of selected setting.

•Turning left selects previous item or decreases value of selected setting.

•While control panel is in sleep mode, turning the knob to either side allows to change the

set temperature/power level of the active mode. Changes are applied without

confirmation.

1.3. BACK BUTTON

Back button is used to return to the previous screen by pressing it once.

1.4. QUICK BUTTON

Quick button can be used to start or stop the heater without entering the main menu or quickly

enabling or disabling timers.

•While the heater is off, pressing the button once opens the “Heating” menu.

•While the heater is off, long-pressing the button for 2 seconds starts the heater with

previous settings (Display message: “Starting…”).

•While the heater is operating, long-pressing the button for 2 seconds switches off the

heater (Display message: “Switching off…”).

•While the heater is operating (and in sleep mode), pressing the button once opens the

settings of the active operation mode. Changes are applied after confirmation.

•In the menu “Timers” pressing the button once enables/disables the selected timer (for

this action timer has to be set beforehand).

1.5. LED INDICATORS

LED indicators are used to indicate the operating mode or status of the heater:

•RED – heater is working in heating mode;

•BLUE – heater is working in ventilation mode;

•GREEN – heater is switching off (purge mode);

•RED (blinking combined with display message) – an error has occurred;

•LIGHT GREEN (one blink every 5 seconds) – a timer has been enabled.

2. MOUNTING AND CONNECTION

Control panel can be mounted using screws or double-sided adhesive tape.

For mounting with screws, gently remove the back panel using a thin flat screwdriver, by prying

it from the middle of one of the sides. Then screw the back panel to your desired surface.

For mounting with double-sided adhesive tape, before installation degrease the back of the

control panel and the desired surface.

To increase the length of control panel wiring, use only designated extension wirings.

When connected to the power supply control panel turns on automatically.

When turned on LED indicators light up, while showing AUTOTERM logos on the display.

Connection process takes approx. up to 20 seconds. If connection is established display shows

main screen. If connection fails message “No connection!” is displayed.

After disconnecting the control panel form the power supply time and date must be

reset. The rest of the settings, such as set timers, remain saved.

Connect temperature sensor to boiler temperature sensor socket and control panel before

connecting heater to power. Temperature sensor cable length is 5 meters.

3. OPERATION AND SETTINGS

3.1. MAIN MENU

The main menu can be accessed from the main screen by pressing the rotary knob once.

Navigate through the menu by turning the knob. To enter the selected menu, press the knob

once.

TIMERS

Is used to set and enable/disable up to 3 timers.

HEATING

Is used to set different heating modes, depending on the

connected heater.

VENTILATION

Is used to set ventilation mode (except for AIR 8D and liquid

heaters).

SETTINGS

Is used to change general settings of the control panel and

heater.

3.2. TIMERS

In “Timers” menu up to 3 timers can be set to start the heater at a

specific time in desired mode for desired duration.

To set timers select the “Timers” menu from the main menu by pressing

the knob once.

Choose one of three timers by rotating the knob and pressing the knob once

to confirm the selected timer.

The default values of the timers are 0:00 –ED –Heating.

Quick button ( ) can be used to enable/disable previously set timers.

After selecting a timer, choose to enable or adjust the timer by rotating the

knob and pressing the knob once to confirm one of the options.

BOILER Is used to set water heating only mode. The heater will

heat, and switch on/off following water temperature.

Editing the timer

Set the time of day for heater to start:

•Set hours and confirm;

•Set minutes and confirm.

Set working duration of the heater.

Duration can be set from 30min to 720min* with increasing step of 5min.

*up to 120min for liquid heaters

Set days for heater to start, where:

•ED (Every Day) – heater starts every day of the

week;

•EW (Every Workday) – heater starts every day from

Monday to Friday;

•SEL (Select specific day) – heater starts only on

specified days, where:

1 – Monday

3 – Wednesday

5 – Friday

7 – Sunday

2 – Tuesday

4 – Thursday

6 – Saturday

Set the operation mode for air heaters:

•Heating mode

•Heat + Ventilation mode

•Ventilation mode

Set the operation mode for liquid heaters:

•Pre-heating mode

When all the parameters are set message “Saved” is shown on the display and

the timer is enabled automatically. Enabled timers can be seen on the bottom

part of the main screen. LED indicators will blink light green once every 5sec

when timer is enabled.

3.3. HEATING

In “Heating” menu different operation modes for heating can be set,

depending on the connceted heater.

To set heater modes select the “Heating” menu from the main menu by

pressing the knob once and then select one of the heating modes:

Temperature can be set in a range of 0°C up to 30°C, with step of 1°C.

Work time can be set by turning the knob in either direction, in a range of

30 min up to infinity (or vice versa) by a step of:

•5min up to 2h;

•20min up to 12h;

•after 12h next step is ∞.

It is impossible to switch to any of heating modes while heater is operating in ventilation

mode!

Heating modes for air heaters:

TEMPERATURE MODE –Heater will maintain set temperature by reducing the

heating power, without shutting off the combustion process.(*)

POWER MODE – Heater will operate constantly at set power level.

HEAT + VENTILATION –

Heater will operate till the temperature is reached 1°C above the

set temperature, shut off the combustion process and start to

ventilate till the temperature drops 5°C below the set

temperature. When temperature drops, heating starts again.

THERMOSTAT MODE –

Heater will operate till the specified temperature is reached then

shuts off the combustion process and ventilation. After the

temperature drops by specified degrees heating will start again.

Setting Temperature mode

Select “Temperature mode” from the menu.

Set temperature and confirm.

Set work time and confirm.

When mode is active, respective symbol is shown on the main screen.

*The temperature mode for Air 2D 12/24V and 4D 12/24V heaters in the 6355, 6350, 6260,

and 6265 series versions have a new algorithm. In this mode, the heater acts normally by

lowering power when it gets near the set temperature. However, if it goes past the

temperature setpoint, the heater will turn off and wait until the temperature drops by 3

degrees below temperature setpoint before starting again.

For Flow 5 and Flow 14 v2 liquid heaters maximum operation time in pre-heating

mode is 8 hours.

Tabla de contenidos

Otros manuales de Controladores de AUTOTERM

AUTOTERM

AUTOTERM PU-16 Manual de usuario

AUTOTERM

AUTOTERM Comfort Control PU-CC Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario