Autostart AS-2500 TW Manual de usuario

AUTOMATIC TRANSMISSION MULTI-CHANNEL

TWO-WAY LCD REMOTE STARTER

SYSTEM

AS-2500 TW

User Guide

Transmitter Part Number and

Module Serial Number .............2

Introduction...............................2

What is “eSH” Technology? .....2

Basic Remote Operation ..........3

LCD Remote Functions............3

Basic Vehicle Operation...........3

Alarm Clock ..............................4

Time Adjust Mode ....................4

Countdown Timer.....................4

Parking Countdown..................4

Melody Selection......................4

Vibration Mode .........................4

Power Saving Mode .................4

Remote Control Finder.............4

LCD Remote Operation............5

Basic Vehicle Operations .....5

Transmitter Mode Selection..5

Alarm and Countdown

Adjustments..........................5

Cold Weather Mode..............6

Home ValetTM........................6

LCD Transmitter Operation and

Confirmations ...........................7

Timing and Alarm Adjustment

..............................................8

Transmitter Finder ................8

Remote-starting Your Vehicle ..8

Vehicle Presets.....................8

Driving Off.............................8

Advanced Features.................. 8

Idle Mode..............................8

Turbo Mode ..........................9

“Home Valet” ™ Mode..........9

Remote Valet Mode..............9

Valet Mode ...........................9

Panic Mode (this option must

be programmed).................10

Quick LockoutTM .................10

Remote Door Locks Option 11

Cold Weather Mode ...........11

Priority Door Access...........11

The user-selectable options

are as follows: ....................11

Remote Door Locks Option 11

Safe Start............................11

Starter Kill Option ...............12

Passive or Active Arming ...12

Ignition-controlled Door Locks

Option.................................12

Ignition Relock....................12

Secure Lock Option............12

Remote Trunk Release

Option.................................12

Engine Run Time................12

Multi-car Operation.............13

Diagnostics – Parking Lights

Flash Rate (Normal Operation)14

H.2.40 S.3.00 Rev: 1.10 June 27, 2003 – Fb CA Manufactured in Canada by Autostart

Transmitter Part Number and Module Serial Number

Transmitter Part Number:

ASTR-5614

Transmitter (companion) Part Number:

ASTR-LCD1

The installer is to write in the following box the Module’s serial number.

Module Serial Number:

Introduction

This system is a state-of-the-art remote car starter system with command confirmation. It re-

presents a major breakthrough in vehicle convenience technology and remote starter systems.

What is “eSH” Technology?

"eSH" technology uses Manchester decoding along with advanced custom data filters to help

reduce data-bit transfer errors. This filtering mechanism minimizes dropped commands by the

transceiver and develops more reliable range. By using narrow band filtering and unique software

driven noise filters, the radio set is able to achieve much better input sensitivity resulting in up to

2,000 feet of operating range.

P. 2 User Guide AS-2500 TW

Basic Remote Operation

This Unit is equipped with a multi-channel 5-button LCD remote transmitter. It can operate two

independent Autostart-equipped vehicles (see Multi-car Operation for 2nd car functions).

The functions of the transmitter are as follows:

Note: Pressing the LOCK and UNLOCK buttons simultaneously will activate the AUX 2 output.

LCD Remote Functions

The Transmitter offers several command-confirmation and timer features.

This section explains some of the key functions available on the Remote

Control. Next section gives a summary of the button combinations used to

access the functions (see LCD Remote Operation Tables).

Note:

If you wish to exit a function while still in the

process of accessing it, simply stop and wait for at

least 10 seconds: the Remote Control will return to

its normal state.

Basic Vehicle Operation

The vehicle can be remote-started and stopped using the START/STOP ( )

button. The TRUNK ( ) button will open the Trunk (if this feature is installed

on the vehicle). The LOCK ( ) and UNLOCK ( ) buttons will lock and unlock

the Doors of the vehicle (if the Remote Door Lock feature is installed on the

vehicle) and arm or disarm the Starter Kill (if installed). The FUNCTION

() button is used to access all advanced functions of the Remote Control.

(Refer to the LCD Operation and Confirmations tables.)

AS-2500 TW User Guide P.3

Alarm Clock

The LCD Remote Control has a built-in Alarm Clock which can be set up

using the button. Use the and buttons to switch the Alarm Clock

on and off (refer to the tables).

Time Adjust Mode

Use Time Adjust Mode to set the current time on your Remote Control

using the button (refer to the tables).

Countdown Timer

This feature allows set up a countdown of a duration entered by the user in

hours and minutes using the button (refer to the tables).

Parking Countdown

This version of the Countdown feature is particularly useful for keeping

track of parking meter time: the user may quickly set up the countdown in

slices of 10 or 30 minutes using the and buttons (refer to the tables).

Melody Selection

The Remote Control allows the user to select which melodies are to be

used upon the following events: remote starting of the vehicle, the Alarm,

ending of the countdown, entering Cold Weather Mode. Melodies for these

various events can be selected using the button (refer to the tables).

Vibration Mode

Use this feature to replace audible signals with a vibration signal. Use

the and buttons to switch Vibration Mode ON and OFF (refer to the

tables).

Power Saving Mode

When set to Power Saving Mode, the Remote Control will cease polling the

Remote Starter Module on a regular basis for status information. This will

extend battery life. Use the and buttons to switch Power Saving

Mode ON and OFF (refer to the tables).

Remote Control Finder

This function allows the user to locate the Remote Control when it has been

accidentally dropped near the vehicle. Pressing the Valet Button and

holding it down for 3 seconds (or until the Parking Lights flash five times)

will cause the Remote Control to start beeping for one minute. The beeping

P. 4 User Guide AS-2500 TW

will stop by itself after one minute, or it can be switched off by pressing the

Lock ( ) or the Unlock ( ) button on the Remote Control.

LCD Remote Operation

(First Car Control)

NOTE:

The following section explains the functions the Transmitter

can provide. If you wish to exit a function while you are

accessing it, simply stop and wait at least 10 seconds, the

Transmitter will return to normal.

Basic Vehicle Operations

FUNCTION BUTTON PRESSED ICON BUZZER INSTRUCTIONS /DESCRIPTION

LOCK 1 Beep LOCK AND ARM THE STARTER

KILL

UNLOCK 2 Beep UNLOCK AND DISARM THE

STARTER KILL

TRUNK OR AUX 3 1 Beep TRUNK OUTPUT

START *

(See Runtime

Options below) +MELODY START THE ENGINE

STOP None MELODY STOP THE ENGINE

Light ON ON for 10 seconds Press once

Transmitter Mode Selection

FUNCTION BUTTON PRESSED ICON BUZZER INSTRUCTIONS /DESCRIPTION

POWER-SAVING

MODE + (+)MELODY

Press UNLOCK first and

then press the Function

button and the Lock button

simultaneously.

VIBRATION MODE

PRESS AND HOLD

AND THEN PRESS VIBRATES 4X

ALARM CLOCK

MODE ON/OFF + MELODY

zPress once to have

ALARM CLOCK ON

zPress twice to have

ALARM CLOCK OFF

Alarm and Countdown Adjustments

On Press

Number FUNCTION BUTTON

PRESSED ICON BUZZER INSTRUCTIONS

/DESCRIPTION

1TIMING ADJUST MODE (HOUR)

Press and hold

for 5 sec

2 BEEPS

2TIMING ADJUST MODE (MIN) 2nd Press of

3ALARM CLOCK ADJUST MODE

(HOUR) 3rd press of

4ALARM CLOCK ADJUST MODE

(MIN) 4th press of

5ALARM CLOCK MUSIC OR

POWER ON MUSIC SELECTION 5th press of

SELECTIONS

1,2,3,4,5

6ALARM CLOCK ADJUST MODE

(ON/OFF) 6th press of /

7TIMING COUNT DOWN ADJUST

MODE (HOUR) 7th press of

zpress for

upward adjustment

or choice ON mode.

zpress for

downward

adjustment or choice

OFF mode.

zTo cycle to the

next options

AS-2500 TW User Guide P.5

8* TIMING COUNT DOWN ADJUST

MODE (MIN) 8th press of

9TIMING COUNT DOWN ENDING

MELODY SELECTION 1 9th press of

SELECTIONS

1,2,3,4,5

10 TIMING COUNT DOWN MODE

(ON/OFF) 10th press of /

11 START COMMAND

CONFIRMATION 11th press of

SELECTIONS

1,2,3,4,5

Cold Weather Mode

FUNCTION BUTTON PRESSED ICON BUZZER INSTRUCTIONS /DESCRIPTION

TO ENTER COLD

WEATHER MODE BEEP Press and hold for 3

seconds.

TO EXIT COLD

WEATHER MODE None None Press and hold for 3 seconds

TO ENTER COLD

WEATHER MODE

IN SAFE START

MODE

X 2 BEEP Press twice within 3 seconds.

Press and hold for 1 sec-BEEP-

then press and hold for 3sec.

TO EXIT COLD

WEATHER MODE

IN SAFE START

MODE

X 2 None None Press twice within 3 seconds.

Press and hold for 1 sec-BEEP-

then press and hold for 3sec.

Home ValetTM

FUNCTION BY PRESSING ICON BUZZER INSTRUCTIONS / DESCRIPTION

TO ENTER HOME

VALET™ MODE

Step 1 : or

Step 2 : +

Simultaneously within 5 sec.

1 BEEP

Press or

Within 5 seconds, press

+: the Transmitter will

display and you will hear 1

beep.

TO EXIT HOME

VALET ™ MODE NONE NONE NONE

INSERT KEY IN INGNITION

SWITCH AND TURN TO THE ON

POSITION. THE ICON WILL

DISAPPEAR.

(See “ON PRESS NUMBER” 8 of Alarm and Countdown Adjustment)

iming Countdown Adjustment

FUNCTION BY PRESSING ICON BUZZER INSTRUCTIONS /

DESCRIPTION

1st time MELODY 10 MIN PARKING COUNT

DOWN MODE

2nd time MELODY 20 MIN PARKING COUNT

DOWN MODE

3rd time MELODY 30 MIN PARKING COUNT

DOWN MODE

4th time MELODY 60 MIN PARKING COUNT

DOWN MODE

5th time MELODY 90 MIN PARKING COUNT

DOWN MODE

6th time MELODY 120 MIN PARKING COUNT

DOWN MODE

FOR PARKING

COUNT DOWN

PRESS AND HOLD

THEN PRESS

7th time MELODY PARKING COUNT DOWN OFF

MODE

P. 6 User Guide AS-2500 TW

Please NOTE:

Once the Countdown is activated it will continue counting

down until reaching 0:00. If the Timer has not reached 0:00

and you are starting the vehicle, you should reset your

Countdown Timer to 0:00 before starting your vehicle as to

avoid being startled.

Safe Start Mode

FUNCTION BY PRESSING ICON BUZZER INSTRUCTIONS /

DESCRIPTION

START ON SAFE

START MODE X 2 +MELODY Press twice within 3 seconds.

Press for 1 sec-melody-then

press 1sec.

STOP ON SAFE

START MODE None MELODY

*Runtime Status (Indication purpose only)

FUNCTION BY PRESSING ICON Gasoline Diesel

4 minutes 9 minutes

ENGINE RUNTIME 15 minutes 20 minutes

25 minutes 30 minutes

LCD Transmitter Operation and Confirmations

(Second Car Control)

Basic Operations

FUNCTION BUTTON PRESS ICON BUZZER DESCRIPTION

LOCK + 1 Beep

UNLOCK + 2 Beep

START + +

MELODY

STOP + None MELODY

TRUNK + +

TRUNK on vehicle

will pop up BEEP

Start/Stop While in Safe Start Mode

FUNCTION BUTTON PRESS ICON BUZZER DESCRIPTION

START ON

SAFE START

MODE + X 2 +

MELODY

Press

+simultaneously twice

within 3 seconds. Press for

1 sec- a BEEP will be

heard- then press 1sec

and a melody will be heard

again.

STOP ON SAFE

START MODE + None MELODY

AS-2500 TW User Guide P.7

P. 8 User Guide AS-2500 TW

Timing and Alarm Adjustment

To apply changes to the hours, minutes melody, etc. you must press and hold the Function button

for three (3) seconds after which the hour position will start to flash. To navigate through the

options, simply press the Function button until you reach the desired position.

Transmitter Finder

If the remote is misplaced, the user can locate it by calling it. In order to do so, press and hold the

Valet switch for three (3) seconds or until the Parking Lights flash five (5) times. The Transmitter

will start beeping. It will beep for a maximum of 60 seconds and then it will stop. If the user

retrieves the Transmitter before the 60 seconds are up, he can press the LOCK or UNLOCK button to

stop the beeping.

Remote-starting Your Vehicle

Press the START/STOP button for approx. 1 second. The melody will play then stop, once the vehicle

starts the melody will play again and the icon “run” will flash for confirmation. The icon will stop

flashing when the key is inserted and turned to the “ON” position or when the entire pre-

programmed engine run time has elapsed.

If the vehicle doesn’t start the first time, the system will shut off, wait a few seconds and try to start

the engine again. It will make three start attempts before giving up.

Vehicle Presets

Heater and Heated Seat: When leaving the vehicle it is recommended to preset the accessory

controls in preparation for the next remote start. Settings for the blower motor (fan), front and rear,

as well as heated seats (if equipped) should not be left on HIGH. It is recommended to leave the

settings on LOW or MEDIUM instead.

Windshield Wipers, Radio and Headlights: Certain vehicles require the radio and / or windshield

wiper and / or headlight circuits to become energized while running under remote start. When

leaving the vehicle you must ensure that the windshield wiper and headlight switches are OFF.

Leaving the headlight switch ON on certain types of vehicles could cause them to remain ON even

after remote starter shut down, resulting in a dead battery.

Driving Off

With the vehicle running under remote control, press the UNLOCK button to disarm the system (and

unlock the doors if Remote Door Locks are installed). Enter the vehicle and do the following:

1. Turn the ignition key to the IGNITION ON (RUN) position.

(Do not turn the key to the CRANK position while the engine is running. This will cause the

starter motor to re-engage unless the Anti-Grind option has been installed.)

2. Press the brake pedal to disengage the remote starter unit.

You are now ready to drive off.

Advanced Features

Idle Mode

This feature allows you to remove the ignition key from the ignition switch and leave the vehicle

running for its pre-programmed run time while you are away from your vehicle, or until it is shut

down. (To set the run time, see Engine Run Time)

To enable the Idle Mode:

3. Press and hold the LOCK,UNLOCK or START/STOP button on your remote transmitter while the

engine is running.

xPressing LOCK or UNLOCK will unlock the doors.

xPressing START/STOP will leave the doors unaffected.

4. The parking lights will come ON.

5. Remove the ignition key, exit the vehicle and lock the doors.

The engine will go on running. It will shut down when the pre-programmed run time expires.

Caution: Do not leave children or pets unattended in a car running

in Idle Mode.

Note: When enabling Idle Mode, pressing LOCK or UNLOCK will

unlock the doors (if Remote Door Locks are installed).

Turbo Mode

When programmed (at the time of installation), this Option allows turbochargers to idle down: after

the user leaves the vehicle, the Engine will keep running for 60 sec. And shut down.

Proceed as follows to activate Turbo Mode:

1. With the Engine already running press LOCK on the Transmitter until the Parking Lights come

on.

2. Remove the key: the Engine will go on running.

3. Exit the vehicle and close the Door.

4. Press the TRUNK button to lock the Doors and shut down the Engine after 60 sec. running

in Turbo Mode.

“Home Valet” ™ Mode

This safety feature will remotely place the vehicle into a no-remote-start mode: if the vehicle is

parked indoors there is no danger it will start accidentally by remote control or external trigger.

To e n t e r Home Valet Mode:

xPress LOCK or UNLOCK on the Transmitter.

xWithin 5 seconds, press LOCK + START: the Transmitter will display the “Valet” icon

and you will hear a beep.

To e x i t Home Valet Mode, turn the ignition key to the IGNITION ON (RUN) position.

Note: Once Home Valet is activated, the vehicle will not start by remote control or external

trigger until the ignition key is turned to the IGNITION ON (RUN) position.

Remote Valet Mode

This feature will allow you to remotely put your system into Valet Mode by using the transmitter

instead of the Valet button as above.

Getting i n t o Valet Mode

xHold the UNLOCK and START/STOP buttons simultaneously for 3 seconds.

xThe Parking Lights will flash 3 times.

The Transmitter will BEEP once and will display the icon; the LED will remain on solid.

Getting o u t of Valet Mode

xHold the UNLOCK and START/STOP buttons simultaneously for 3 seconds.

xThe Parking Lights will flash 2 times.

The Transmitter will BEEP once and the icon will disappear; the LED will turn off.

Note:

With the Remote Valet activated, the

remote starter function will be disabled.

Ignition Valet

This feature allows the user to enter Valet Mode by using only the Ignition key. It may need to be

programmed, please refer to the Options Programming section in the Installation Guide to find out.

AS-2500 TW User Guide P.9

To ENTER Valet Mode

1. With the key in the Ignition switch, turn the key to the ON (RUN/IGNITION) and then OFF positions 5

times within 10 seconds.

2. The Parking Lights will flash 3 times indicating the Module is now in Valet Mode. The LED will

turn ON solid.

To EXIT Valet Mode

3. With the key in the Ignition switch, turn the key to the ON (RUN/IGNITION) and then OFF positions 5

times within 10 seconds.

4. The Parking Lights will flash twice indicating the Module is now out of Valet Mode. The LED

will turn OFF.

Valet Mode

The system can be placed in Valet Mode to disable the remote starting capabilities. If the vehicle

needs to be serviced, or if you park it indoors, the Valet Mode will prevent the engine from being

accidentally started by remote control.

To put the system i n t o Valet Mode:

1. Turn the ignition key to the IGNITION ON (RUN) position.

2. Within 3 sec. press and hold the valet button for approx. 1 sec. The L.E.D. will turn ON and

remain lit.

3. The Transmitter will display the Valet icon .

To take the system o u t o f Valet Mode:

1. Turn the ignition key to the IGNITION ON (RUN) position.

2. Within 3 sec. press and hold the valet button for approx. 1 sec. The L.E.D. will go OFF. The

Valet Icon will disappear from the Transmitter screen.

The valet button can only be used if the ignition key is in the IGNITION ON (RUN) position.

Panic Mode (this option must be programmed)

In an emergency situation, you can activate Panic Mode using the LOCK or UNLOCK button. This will:

xShut down the engine,

xUnlock the doors (if UNLOCK is pressed)

xor lock the doors (if LOCK is pressed),

xDisarm the Starter Kill and

xActivate the horn for 30 seconds.

(See page 4 for a description of the Starter Kill option.)

To trigger Panic Mode:

xPress and hold the UNLOCK button for approximately 3 seconds until the horn starts to sound

and the parking lights flash: this will unlock the doors before the horn starts.

xOr press and hold the LOCK button for approximately 3 seconds until the horn starts to sound

and the parking lights flash: this will lock the doors before the horn starts.

Panic Mode will automatically shut off after 30 seconds.

Note: If you want to stop Panic Mode before the 30-

second delay, press the LOCK or UNLOCK button.

Caution: Panic Mode will be available only if Horn

Confirmation was configured at installation.

Quick LockoutTM

(Also called Secure Panic.) For fast protection, the system will LOCK all doors when you press the

brake pedal while the horn is activated and the system is in Panic Mode. (Quick Lockout is

only available when Panic Mode has been activated.)

P. 10 User Guide AS-2500 TW

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Arranque remoto de Autostart

Autostart

Autostart ANT-4420 Manual de usuario

Autostart

Autostart AS-2272 Manual de usuario

Autostart

Autostart AS-6105 SH Manual de usuario

Autostart

Autostart AS-1525 SH Manual de usuario

Autostart

Autostart AS-3372TW-FM Manual de usuario

Autostart

Autostart AS-1725iSH Manual de usuario

Autostart

Autostart AS-6205 Manual de usuario

Autostart

Autostart AS-3372 TW-FM Manual de usuario

Autostart

Autostart AS-1585 SH Manual de usuario

Autostart

Autostart as2520 Manual de usuario

Autostart

Autostart AS-1755V Manual de usuario

Autostart

Autostart AS-2350vTW-FM Manual de usuario

Autostart

Autostart AS-1795 Manual de usuario

Autostart

Autostart 4-Button Manual/ Automatic Transmission Remote Starter with Virtual Tach... Manual de usuario

Autostart

Autostart AS-2300TW Manual de usuario

Autostart

Autostart AS-1414 Manual de usuario

Autostart

Autostart GS-1655 Manual de usuario

Autostart

Autostart None Manual de usuario

Autostart

Autostart AS-2660i TW-FM Manual de usuario

Autostart

Autostart AS-1725 SH Manual de usuario

Autostart

Autostart AS-6450VTW-FM Manual de usuario

Autostart

Autostart AS-6850TW-FM Manual de usuario

Autostart

Autostart AS-3372 TW-FM Manual de usuario

Autostart

Autostart AS-1484iHF Manual de usuario

Manuales populares de Arranque remoto de otras marcas

AstroStart

AstroStart 803U Manual de usuario

Durite

Durite 0-649-20 Manual

EINHELL

EINHELL BT-PS 1000 Manual

Linear

Linear ACCESS AK-21 Especificaciones técnicas

Soundstream

Soundstream TARANTULA RS.2 Manual de usuario

Jaycar Electronics

Jaycar Electronics MB3752 Manual de usuario

Ultra Start

Ultra Start 72 Series Manual de usuario

ADS

ADS FLASHLOGIC FLRSVW1 Manual de usuario

Selecta

Selecta JS012 Manual de usuario

Black Widow Security

Black Widow Security BW RAS 400 Manual de usuario

Vector

Vector Power City DK080706 Suplemento

Code Alarm

Code Alarm CA-535 Manual de usuario

Ozito

Ozito OJS-800 Manual de usuario

Profi-Partner

Profi-Partner 46387 Manual de usuario

EZ STARTER

EZ STARTER EZ-45 Manual de usuario

Viper

Viper 4204 Manual de usuario

Essex Electronics

Essex Electronics KE-1701 Manual de usuario

EINHELL

EINHELL EGS 3600 Manual