autosen AF004 Manual de usuario

Operating instructions
Electronic level sensor
autosen AF004
80259948 00 12/2016
Made in Germany
UK

2
Contents
1 Preliminary note���������������������������������������������������������������������������������������������������4
1�1 Symbols used ������������������������������������������������������������������������������������������������4
2 Safety instructions �����������������������������������������������������������������������������������������������4
3 Items supplied������������������������������������������������������������������������������������������������������5
4 Functions and features ����������������������������������������������������������������������������������������7
4�1 Operation with single probe���������������������������������������������������������������������������7
4�2 Operation with coaxial probe �������������������������������������������������������������������������7
4�3 Applications ���������������������������������������������������������������������������������������������������8
4�3�1 Restriction of the application area ��������������������������������������������������������8
5 Function���������������������������������������������������������������������������������������������������������������9
5�1 Measuring principle ���������������������������������������������������������������������������������������9
5�2 Features of the unit��������������������������������������������������������������������������������������10
5�2�1 Easy set-up�����������������������������������������������������������������������������������������10
5�2�2 Display functions ��������������������������������������������������������������������������������10
5�2�3 Switching functions�����������������������������������������������������������������������������10
5�2�4 Offset for indicating the real level in the tank�������������������������������������� 11
5�2�5 Probes for different tank heights��������������������������������������������������������� 11
5�2�6 Safe state �������������������������������������������������������������������������������������������12
5�3 IO-Link ���������������������������������������������������������������������������������������������������������12
6 Installation����������������������������������������������������������������������������������������������������������13
6�1 Installation location / environment ���������������������������������������������������������������13
6�1�1 Unit with single probe �������������������������������������������������������������������������13
6�1�2 Unit with coaxial probe �����������������������������������������������������������������������16
6�2 Installation of the probe �������������������������������������������������������������������������������16
6�2�1 Installation of the rod ��������������������������������������������������������������������������17
6�2�2 Installation of the coaxial pipe ������������������������������������������������������������18
6�3 Shortening of the probe �������������������������������������������������������������������������������19
6�3�1 How to shorten the rod and determine its length L�����������������������������19
6�3�2 Shortening of the coaxial pipe ������������������������������������������������������������19
6�3�3 Determination of the rod length L when coaxial probes are used�������20
6�4 Installation of the unit with single probe�������������������������������������������������������20
6�4�1 Installation in closed metal tanks (without flange plate) ���������������������21
6�4�2 Installation in closed metal tanks (with flange plate) ��������������������������21
6�4�3 Installation in open tanks ��������������������������������������������������������������������22

3
UK
6�4�4 Installation in plastic tanks������������������������������������������������������������������23
6�5 Installation of the unit with coaxial probe in the tank �����������������������������������23
6�6 Alignment of the sensor housing �����������������������������������������������������������������24
7 Electrical connection������������������������������������������������������������������������������������������24
8 Operating and display elements ������������������������������������������������������������������������25
9 Menu������������������������������������������������������������������������������������������������������������������26
9�1 Menu structure���������������������������������������������������������������������������������������������26
9�2 Explanation of the menu������������������������������������������������������������������������������27
10 Parameter setting ��������������������������������������������������������������������������������������������28
10�1 Parameter setting in general ���������������������������������������������������������������������28
10�2 Basic settings (unit on delivery)�����������������������������������������������������������������30
10�2�1 Entering the probe length �����������������������������������������������������������������30
10�2�2 Setting to the medium�����������������������������������������������������������������������30
10�2�3 Entering the type of probe used �������������������������������������������������������30
10�3 Configuration of the display �����������������������������������������������������������������������31
10�4 Offset setting����������������������������������������������������������������������������������������������31
10�5 Setting of output signals ����������������������������������������������������������������������������31
10�5�1 Setting of the output function������������������������������������������������������������31
10�5�2 Set the switching limits (hysteresis function) ������������������������������������31
10�5�3 Set the switching limits (window function) ����������������������������������������32
10�5�4 Setting of the switch-off delay�����������������������������������������������������������32
10�5�5 Response of the outputs in case of a fault ���������������������������������������32
10�5�6 Setting of the delay time after signal loss �����������������������������������������32
10�6 Reset all parameters to factory setting ������������������������������������������������������32
10�7 Changing basic settings ����������������������������������������������������������������������������33
10�7�1 Re-enter the probe length�����������������������������������������������������������������33
10�7�2 Setting to another medium ���������������������������������������������������������������33
10�7�3 New entering of the type of probe used��������������������������������������������33
11 Operation ���������������������������������������������������������������������������������������������������������34
11�1 Operating indicators ����������������������������������������������������������������������������������34
11�2 Read the set parameters ���������������������������������������������������������������������������34
11�3 Changing the display unit in the Run mode �����������������������������������������������34
11�4 Error indications�����������������������������������������������������������������������������������������35
11�5 Output response in different operating states��������������������������������������������36
12 Technical data and scale drawing��������������������������������������������������������������������36
12�1 Setting ranges ������������������������������������������������������������������������������������������36

4
1 Preliminary note
1.1 Symbols used
►Instructions
> Reaction, result
[…] Designation of keys, buttons or indications
→Cross-reference
Important note
Non-compliance may result in malfunction or interference�
Information
Supplementary note�
2 Safety instructions
• Please read this document prior to set-up of the unit� Ensure that the product is
suitable for your application without any restrictions�
• If the operating instructions or the technical data are not adhered to, personal
injury and/or damage to property can occur�
• Improper or non-intended use may lead to malfunctions of the unit or to
unwanted effects in your application� That is why installation, electrical
connection, set-up, operation and maintenance of the unit must be carried out
by qualified personnel authorised by the machine operator�
• In order to guarantee the correct operation of the unit, it is necessary to use the
unit in media to which it is sufficiently resistant (→ Technical data).
13 Servicing����������������������������������������������������������������������������������������������������������37
14 Applications������������������������������������������������������������������������������������������������������38
14�1 Minimum level monitoring with early warning and alarm ���������������������������38
14�2 Pumping station / empty the tank with overflow protection������������������������39
14�3 Storage tank ����������������������������������������������������������������������������������������������40
15 Factory setting �������������������������������������������������������������������������������������������������41

5
UK
• The responsibility as to the suitability of the unit for the application lies with the
operator� The manufacturer assumes no liability for consequences of misuse by
the operator�
• Improper installation and use of the unit result in a loss of the warranty claims
• The unit may cause radio interference in domestic areas� If interference occurs,
the user must take appropriate remedial actions�
• The unit complies with the standard EN 61000-6-4 and is a class A product�
The radiated energy of the microwaves is, for example, much below that of
mobile phones� According to the current state of science the operation of the
unit can be classified to be harmless to human health�
3 Items supplied
• Level sensor AF004
• Operating instructions
In addition, the following is necessary for installation and operation:
• 1 rod (for operation of the unit with single probe → 4.1)
• plus 1 coaxial pipe (for operation of the unit with coaxial probe → 4.2)
• mounting material (if necessary, a launching plate → 4.1)

6
The following components are available as accessories:
Rods Length (cm / inch) Order number
45 / 17,7 AA926
70 / 27,6 AA927
100 / 39,4 AA928
160 / 63�0 AA944
Coaxial pipes
with process connection G¾ Length (cm / inch) Order number
45 / 17�7 AA929
70 / 27�6 AA930
100 / 39�4 AA931
160 / 63�0 AA945
Flange plates Size / process connection Order number
73 - 90 / G¾ AA941
65 - 80 / G¾ AA942
Only use rods and coaxial pipes from autosen gmbh� The optimum
function is not ensured when using components from other manufacturers�

7
UK
4 Functions and features
The unit continuously detects the level in tanks and generates output signals
according to the parameter settings�
2 switching outputs are available� They can be set separately�
4.1 Operation with single probe
The single probe is made up of one individual rod� Operation with single probe is
suited for the detection of aqueous media, in particular of heavily soiled aqueous
media�
For the correct function when used with single probe, the unit needs a
large enough metal launching plate� It is necessary for transferring the
microwave pulse to the tank with optimum transmission power�
The flange plates that are available as accessories are not sufficient as
launching plates (for suitable launching plates → 6.4).
For installation in closed metal tanks, the tank lid serves as a launching
plate� For installation in open metal tanks, tanks made of plastic or metal
tanks with plastic lids a sufficiently large fixing plate, a metal plate or
similar must be used (→ 6.4.3 / → 6.4.4).
For operation with single probe, minimum distances to tank walls, objects
in the tank, bottom of the tank and further level sensors must be adhered
to (→ 6.1.1).
4.2 Operation with coaxial probe
The coaxial probe is made up of an inner rod and an outer probe pipe
(coaxial pipe)� The rod is centred in the coaxial pipe by one or several spacers�
In case of operation with a coaxial probe media with a low dielectric constant
(e�g� oil and oil-based media) are detected in addition to aqueous media�
No launching plate is required for operation with coaxial probe�
Furthermore, no minimum distances to tank walls and objects in the tank
are required�

8
4.3 Applications
• Water, water-based media
• Oils, oil-based media (only for operation with coaxial probe)
Application examples:
• Detection of coolant emulsion in a machine tool�
• Detection of cleaning liquid in a parts cleaning system�
• Monitoring of hydraulic oil in a hydraulic power unit (only for operation with
coaxial probe)�
4.3.1 Restriction of the application area
Incorrect measurements or signal loss may be caused by the following
media:
- Highly absorbing surfaces (e�g� foam)�
- Intensely bubbling surfaces�
- Media which are very inhomogeneous, separate from each other thus
forming separation layers (e�g� oil layer on water)�
►Check the function by performing an application test�
► Installation in a steady area (→ 6.1).
> In case of signal loss, the unit displays [E�033] and switches the
outputs to a defined state (→ 11.5).
• The unit is not suitable for bulk materials (e�g� plastic granulates)�
• If the unit is to be used in acids or alkalis, in hygienic areas or in electroplating
applications: first check the compatibility of the product materials (→ 12
Technical data and scale drawing) with the media to be monitored�
• The unit is not suitable for applications where the probe is subjected to
permanent and high mechanical stress (e�g� strongly moving viscous media or
strongly flowing media)�
• In case of operation with single probe: use preferably in metal tanks� When
installed in plastic tanks, deterioration caused by electromagnetic interference
may occur (noise immunity according to EN61000-6-2)�
Corrective measures: → 6.4.4.
• In case of operation with coaxial probe: not suitable for soiled or viscous media
and media prone to formation of deposit�
Maximum viscosity: 500 MPa
·
s�

9
UK
5 Function
5.1 Measuring principle
Fig. 5-1 Fig. 5-2
D
The unit operates to the principle of guided wave radar� It measures the level
using electromagnetic pulses in the nanosecond range�
The pulses are transmitted by the sensor head and guided along the rod (fig� 5-1)�
When they hit the medium to be detected they are reflected and guided back
to the sensor (fig� 5-2)� The time between transmitting and receiving the pulse
directly relates to the travelled distance (D) and the current level� The reference for
distance measurement is the lower edge of the process connection�
The figures show operation with single probe� In case of operation with a
coaxial probe, the guided wave runs only along the inside of the coaxial
pipe�

10
5.2 Features of the unit
5.2.1 Easy set-up
• When the unit is supplied with operating voltage for the first time, the probe
length, the medium to be detected and the type of probe used must be entered�
Then the unit is ready for operation (→ 10.2).
• If necessary, parameters for the output signals and optimisation of the
monitoring functions can be set (→ 10.3 to → 10.5).
• All settings can also be carried out before installation of the unit�
• Reset to the factory settings is possible�
• Electronic lock can be set to prevent unintentional operations�
5.2.2 Display functions
The unit displays the current level, either in cm, inch or in percent of the final
value of the measuring range� Factory setting: cm� The display unit is defined by
programming (→ 10.3). In the Run mode, it can be temporarily switched between
length indication (cm / inch) and percentage:
►briefly press [Set]�
> The selected unit is displayed for 15 s, the corresponding LED is lit� With each
push of the button the display type is changed�
The set unit of measurement and the switching status of the outputs are indicated
by LEDs�
5.2.3 Switching functions
The unit signals via two switching outputs OUT1 / OUT2 that a set limit level
has been reached or that the level is below the limit value� For each output the
following switching functions can be selected:
• Hysteresis function / normally open (fig� 5-3): [OUx] = [Hno]�
• Hysteresis function / normally closed (fig� 5-3): [OUx] = [Hnc]�
First the set point (SPx) is set, then the reset point (rPx) with the requested
difference�
Tabla de contenidos
Otros manuales de Accesorios de autosen

autosen
autosen AC004 Manual

autosen
autosen AU001 Manual de usuario

autosen
autosen AU011 Manual de usuario

autosen
autosen AF005 Manual de usuario

autosen
autosen AP008 Manual de usuario

autosen
autosen AL007 Manual de usuario

autosen
autosen AC005 Manual de usuario

autosen
autosen AL006 Manual de usuario

autosen
autosen AL001 Manual de usuario

autosen
autosen AL002 Manual de usuario






















