Auto Page RS-622 Manual de usuario

RS-622

PROFESSIONAL 2-WAY AM/AM REMOTE CAR STARTER

KEYLESS ENTRY SYSTEM

OPERATIONS MANUAL

Please register your product at

www.autopageusa.com

THIS

PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY

SYSTEM OPERATIONS:

WARNINGS:

As with any product that performs automatic functions, there are certain safety

precautions that you must practice and be aware of.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while the vehicle is running on remote

control.

3. Alert servicing personnel that the vehicle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or garage.

5. Always apply the parking brake and lock the vehicle as you exit the vehicle.

6. The vehicle windows must be rolled up.

7. Should the unit malfunction, disconnect the fuse until the problem is corrected.

8. The use and operations of this system is the sole responsibility of the operator.

9. Some areas may have local ordinances that prohibit leaving a vehicle running

on public streets.

10.It is not safe to remote start the vehicle if the vehicle is parked on a steep

incline.

Transmitter

Button System Function Remark

Lock Doors All doors lock

Panic function Press and Hold for 3 seconds.

Press to stop panic.

+ Silent Lock / Unlock Ignition in "off" position.

Unlock Doors

-Two Step Door Unlock (Driver’s door

on the first push; Passenger’s door

on the second push ( optional ) Press twice within 3 seconds.

+Car Locator Push while the system is armed

Trunk Release Press and Hold for 2 seconds

Activate or Turn Off The Remote

Start Push once or twice depending on

system settings (Program)

II Switching Code For 2nd Car

Operation.Standard Remote only Push Before Command

CHANGING THE B

ATTERY IN YOUR TRANSMITTERS

XT-33: This transmitter uses two (2) 3-volt lithium ion batteries

(#CR2016) that are sandwiched together with the (+) side facing upward.

To replace the battery, you will need to use a small flat blade screwdriver.

Locate the small notch on the lower right side of the transmitter case

next to the key ring. Using the flat blade screwdriver, carefully pry the

top case from the bottom case. It should snap apart after breaking the

seal. Before removing the batteries note the direction of the positive (+)

terminal. Place the new batteries in exactly the same manner, being

careful not to bend or damage the contact terminal. Snap the cases

back together and then test the transmitter to insure it arms and disarms

the alarm.

XT-42LCD 2-Way XT-33

Transceiver Standard Remote

(1) AAA Battery

ACTIVE LOCK:

1. Press button on the transmitter.

2. The Siren will chirp once and parking lights will flash once indicating

that the system is now active. The vehicle doors will lock upon

activating only when interfaced with the keyless entry system.

SILENT LOCKING / UNLOCKING: Pressing the + buttons

together on the transmitter will lock or unlock your system, No chirp

sound will be heard. Lock / unlock confirmation will be seen through the

vehicle’s parking lights only.

ACTIVE UNLOCK:

1. Press button on the transmitter.

2. The horn will chirp twice and parking light will flash twice to indicating

that the keyless system is now unlocked. The vehicle doors will

(2) CR2016

3-Volt Batteries

unlock and dome lights will turn on for 30 seconds.

PATHWAY ILLUMINATION

This feature turns the parking light “ON” for 30 seconds upon a unlock

signal and for 10 seconds upon the lock signal. (Programmable)

TWO STEPS DOOR UNLOCK: This feature will independently unlock

the driver door only when deactivating the system. Pushing the

button a second time within 3 seconds will unlock the entire vehicle.

(Optional)

LED DISPLAY:

LED Function

Off Unlock

Slow Flash Locked

On (Solid) Valet Mode

CHIRP INDICATOR:

Chirp Function

1 Chirp Lock

2 Chirps Unlock

6 Chirps Car Locator

PARKING LIGHTS:

Parking light Function

1 Flash Lock

2 Flashes Unlock

12 Flashes Car Locator

Constant On Under Remote Start

DEACTIVATING WITHOUT A TRANSMITTER

The Override function may be used if the remote transmitter is lost or

inoperative.

1. Enter the vehicle and turn the ignition switch to ‘ON’ position.

2. Within 10 seconds push and release the valet switch.

You can now start and operate the vehicle normally.

VALET MODE:

The valet switch allows you to temporarily bypass all system function,

eliminating the need to hand your transmitter to parking attendants or

garage mechanics. When the system is in valet mode, and remote start

functions are bypassed, however, the remote panic feature and remote

door locks will remain operational. To use the valet mode, the system

must first be deactivated either by using you remote transmitter, or by

operating the Manual override sequence.

Enter Valet Mode:

1. From the Unlock condition, turn the ignition to “ON” position.

2. Push and hold valet switch for 2 seconds until the LED turns on.

The LED will remain on as long as the system is in ‘valet mode’.

Exit Valet Mode:

1. Return to normal operation, turn ignition ‘on’.

2. Push and hold valet switch for 2 seconds, The LED will turn off

indicating the system has exited the valet mode.

PANIC FUNCTION: (IF SIREN or HORN IS INSTALLED)

The transmitter can be used as a remote panic switch to manually

trigger the vehicle’s horn in case of emergency.

1. Press and hold the button for 3 second. The siren will

immediately sound.

2. During panic mode, the normal function of this transmitter button

will be suspended. The and buttons can be used to lock and

unlock the doors (if the option is installed),

3. To stop the panic, press the button on the transmitter again.

4. If no buttons are pressed, the panic function will stop automatically

in 30 seconds.

DOME LIGHT CONVENIENCE DELAY & SUPERVISION

This system has a unique feature, which will turn on your vehicle

dome light as follows: (optional) Additional installation required.

1. Upon unlocking, the interior lights will remain on for 30 seconds.

Note: Turning on the ignition switch or activating the system will turn

off the dome light.

IGNITION CONTROL DOOR LOCKS

If the vehicle’s door locks have been interfaced to the security system,

the system will automatically lock the vehicle’s doors when the ignition

is turned “ON” and /or unlock the vehicle’s doors when the ignition is

turned “OFF”.

TRUNK RELEASE (Additional Installation Required)

Press and hold the button on transmitter for two seconds to remote

control the trunk release or other electric devices.

CAR LOCATOR (ONLY IF SIREN or HORN IS INSTALLED)

Press the button twice when the system is armed to active car

locator function. The horn will chirp 6 times. The parking light will flash

12 times, for you to easily locate your car.

REMOTE START OPERATION:

WARNINGS:

As with any product that performs automatic functions, there are certain

safety precautions that you must practice and be aware of.

1. Keep the transmitter out of children’s reach.

2. Do not leave anyone in the vehicle while running on remote control.

3. Alert servicing personnel that the vehicle can be started automatically.

4. Do not start the vehicle by remote while it’s in an enclosed area or

garage.

5. Always apply the parking brake and lock the vehicle as you exit the

vehicle.

6. Should the unit malfunction, disconnect the fuse until the problem is

corrected.

7. The use and operations of this system is the sole responsibility of the

operator.

8. Some areas may have local ordinances that prohibit leaving a vehicle

running on public streets.

A. TO REMOTE START THE VEHICLE:

When you want to start your vehicle,

1. Press button once on the transmitter.

2. The parking lights will flash to indicate the remote start received the

signal.

3. The engine will start in approximately 5 seconds.

4. A few seconds after the engine is running, the parking lights will turn

on again and climate controls will activate and adjust the vehicles

interior temperature to your preset setting.

5. The vehicle will run for a 5 to 30 minute cycle and automatically shut

down.

(SAFETY START OPERATION :)

The safety start feature allows you to press the button twice before

the vehicle will remote start or remote shut down. (Programming

Required)

NOTE: The Remote Start Unit will not start the vehicle if any one of the

following conditions exists:

1. The hood is opened.

2. The brake pedal is pressed.

3. The optional remote start enable toggle switch is in the OFF position.

4. The gear selector is in any gear other then “PARK” or “NEUTRAL”

TO TURN OFF THE REMOTE START:

When the engine is running (by remote start), if you want to stop it,

1. Press button once on the transmitter.

Move the optional remote start enable toggle switch to OFF position.

(If installed)

3. Press the brake pedal, the vehicle will shut down and turn off the

parking light to indicate engine stopped.

TO OVERRIDE VEHICLE FROM REMOTE START CONTROL:

To operate the vehicle while it is running from the remote start:

1.Insert the ignition key and turn it to “ON” (not the start) position.

2.Press the brake pedal.

Note: If the brake pedal is pressed before the key is in the ON

position, the engine will shut down.

TEMPORARY STOP FEATURE:

This feature allows the vehicle to remain running after the key has been

removed from the ignition. This feature is useful for occasions when you

wish to exit and lock the vehicle for short periods of time, but would like

to leave the engine running and the climate control on.

1.Before turning off the engine, press the button once on the

transmitter. The parking lights will come on and the LED will flash 3

times to confirm Temporary Stop feature ‘ON’

2.Turn the ignition key to OFF position. (The engine will stay running.)

3.The engine will run until the pre-programmed time elapsed or

shutdown input is received.

TIMER START: You must fully understand this feature to operate the

remote start safely. Use caution in using this feature.

This unit can be programmed to start and run the engine every 3 hours.

The engine will run for the programmed run time and then shut down.

IMPORTANT: Timer Start should be used only in open areas, NEVER

start and run the vehicle in on enclosed space such as a garage or

carport.

Three hours timer start: This feature is design for an extreme cold

climate usage. The system will auto start the vehicle every 3 hours, to

prevent engine freezing and hard to start.

A maximum of six cycles can occur.

ENTER:

1. Press the button once to remote start the vehicle. As soon as the

vehicle is running the parking lights will turn ‘ON’.

2. Immediately press the button then press button. The parking

light will flash (3) times. The siren chirps (3) times. The vehicle is now

programmed to start every (3) hours.

3. Press the brake pedal to stop the vehicle running.

Exit the timer start:

Timer start can be exited manually as follows:

1. Repeat the Enter Steps from above.

1. Make sure the remote start system is not operating the engine.

2. Turn the ignition on. The LED and parking light will flash (4) times.

The siren chirps (4) times.

SHUTDOWN INPUT FOR REMOTE STARTER:

If any of the following conditions exist while the system is operating, the

engine will not start or will shut down immediately:

1. The hood is opened.

2. The brake pedal is pressed.

3. The optional remote start enable toggle switch is in the OFF position.

4. Engine is over-revved. {“Tachometer checking type” only}

5. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed.

6. Transmitter button is pressed.

7. The vehicle refused to start running after {3} unsuccessful attempts.

DISABLING THE REMOTE START SYSTEM: (If Optional toggle switch

is installed)

This feature allows your system’s remote start unit to be temporarily

disabled to prevent the vehicle from being remote started accidentally.

This feature is useful if the vehicle is being serviced or stored in an

enclosed area. To disable the remote start, move the optional remote

start enable toggle switch to the OFF position. Valet mode can also be

used. XT-42 LCD TRANSMITTER OPERATION:

LCD REMOTE CONTROL TRANSMITTER:

BATTERY REPLACEMENT:

A 1.5V type AAA Alkaline battery

powers the Remote Transmitter. When

the power of the battery weakens a

icon shall be displayed on the

LCD screen. When the old battery is

replaced with a new one, there will be

beep sounds indicate the power is up.

Note: Press the button two times

when the battery compartment is

empty, and then insert the new

battery.

THE REMOTE LCD ICONS WITH FUNCTION:

Door Lock

Your vehicle doors are

locked.

Door Unlock Your vehicle

doors are unlocked

Start Mode

Your vehicle is running

Valet Mode

All the function shall be

temporarily on hold.

Note: If the system is interfered by stronger radio

frequency around, sources of high voltage electric

power or such obstacles like tall buildings and so

on, the transmission range may get shorter as the

system uses low output powered frequency.

AAA

Remote Transmission

You are transmitting the

signal to control unit

In –Range Indicator

You are within the remote

control range.

Trunk Release Trunk

open. Trunk symbol only.

Low Battery

You have to replace the

battery of remote control.

Vibration Mode

Remote Control vibrates

when the system is

triggered Ignition On

Power Save Mode

Save the battery power

Driver paging

Someone is paging you in

front of your vehicle. **

** Press the valet switch in the vehicle with the Ignition OFF to page

the driver carrying the XT-42 two-way remote control.

PROGRAM MODE FORLCD REMOTE CONTROL TRANSCEIVER:

Press and hold all four remote control buttons simultaneously unit

one long beep is heard. LCD Programming has now been entered.

Transceiver

Button System Function Remark

Program Mode

-Switching code for 2nd /1st Car

Operation Press within 5

seconds

Program Mode

-Melody / Vibration Mode Press within 5

seconds

Program Mode

-Power Save Mode Press within 5

seconds

LCD screen lamp turns on for 5

seconds.

-+Clear the Flash Icon and Melody

Sound Press within 3

seconds

1. Second Vehicle Security Operation: Your remote transmitter can be

utilized to control a second vehicle’s Auto Page security system.To

program the remote control transmitter to a second vehicle, follow the

instructions for Transmitter programming. All programming parameters

are the same except for the following:

Tabla de contenidos

Otros manuales de Arranque remoto de Auto Page

Auto Page

Auto Page RST-1100 Manual de usuario

Auto Page

Auto Page RF-1055KE Manual de usuario

Auto Page

Auto Page C3-RS-603 Manual de usuario

Auto Page

Auto Page RS-615 Manual de usuario

Auto Page

Auto Page C3-RS-625 Manual de usuario

Auto Page

Auto Page RF-225 Manual de usuario

Auto Page

Auto Page C3-RS-665 Manual de usuario

Auto Page

Auto Page RS-730 Manual de usuario

Auto Page

Auto Page C3-RS-625 Manual de usuario

Auto Page

Auto Page Car-Pro CPX-RS2 Manual de usuario

Auto Page

Auto Page C3-RS1100 OLED Manual de usuario

Auto Page

Auto Page RS-615 Manual de usuario

Auto Page

Auto Page Car-Pro CPX-RS2 Manual de usuario

Auto Page

Auto Page RS-601 Manual de usuario

Auto Page

Auto Page RS-855lcd Manual de usuario

Auto Page

Auto Page RS-601 Manual de usuario

Auto Page

Auto Page RS-727LCD Manual de usuario

Auto Page

Auto Page C3-RS-603 Manual de usuario

Auto Page

Auto Page C3-RS-1000 OLED Manual de usuario

Auto Page

Auto Page Car-Pro CPX-RS1 Manual de usuario

Auto Page

Auto Page TRX96 Manual de usuario

Auto Page

Auto Page RS-650 Plus Manual de usuario

Auto Page

Auto Page RS720LCD Manual de usuario

Auto Page

Auto Page Car-Pro CPX-RS1 Manual de usuario

Manuales populares de Arranque remoto de otras marcas

AstroStart

AstroStart 803U Manual de usuario

Durite

Durite 0-649-20 Manual

EINHELL

EINHELL BT-PS 1000 Manual

Linear

Linear ACCESS AK-21 Especificaciones técnicas

Soundstream

Soundstream TARANTULA RS.2 Manual de usuario

Jaycar Electronics

Jaycar Electronics MB3752 Manual de usuario

Ultra Start

Ultra Start 72 Series Manual de usuario

ADS

ADS FLASHLOGIC FLRSVW1 Manual de usuario

Selecta

Selecta JS012 Manual de usuario

Black Widow Security

Black Widow Security BW RAS 400 Manual de usuario

Vector

Vector Power City DK080706 Suplemento

Code Alarm

Code Alarm CA-535 Manual de usuario

Ozito

Ozito OJS-800 Manual de usuario

Profi-Partner

Profi-Partner 46387 Manual de usuario

EZ STARTER

EZ STARTER EZ-45 Manual de usuario

Viper

Viper 4204 Manual de usuario

Essex Electronics

Essex Electronics KE-1701 Manual de usuario

EINHELL

EINHELL EGS 3600 Manual