Audiovox FR-1438-2 Manual de usuario

Model FR-1438-2

Modèle FR-1438-2

Owner’s Manual

Manuel d'utilisation

1. BatteryDoor

2. Monitor Button

3. Detachable Belt Clip

4. Push-To-Talk (PTT) Button

5. Antenna

6. External Speaker Jack

7. Built-in Speaker

8. Liquid Crystal Display (LCD)

9. Built-inMicrophone

10. Up Button and Volume Control

11. Down Button and Volume Control

12. Function Button

13. Power On/Off and ENTER Button

PTT

912

Model FR1438-2 DISPLAY

1. RSSI Indicator: Receive signal strength indicator.

2. TX: Icon blinks during transmission.

3. Monitor Indicator: Icon appears when the monitor button is pressed.

4. Coded Tone Controlled Squelch System (CTCSS) Indicator: Icon appears

when receiving a transmission with correct CTCSS tone.

5. Auto Scan Indicator: Icon appears when the auto scan channel mode is

activated.

6. Dual Watch Scan Indicator: Blinks in dual watch scan mode or when the dual

watch scan mode is activated.

7. Voice Activated Transmission (VOX) Indicator: Blinks in the VOX selection

mode or appears when VOX is activated.

8. Key Lock Indicator: Blinks in autolock selection mode or appears when the

key lock is activated.

9. Call Indicator: This icon blinks in call selection mode and appears when the

unit is transmitting the call tone.

10. Battery Level Indicator: Icon indicates the battery charge strength.

11. Power Saver Indicator: Icon blinks to indicate the power saver is activated.

The rate at which the icon blinks varies with the power saving ratio. Fast

blinking indicates a lower power saving while slow blinking indicates a higher

power saving ratio.

12. TX Indicator: Icon appears when a signal is being transmitted.

13. RX Indicator: Icon appears when a signal is being received.

14. Large SegmentDisplay: Indicatesthechannel numberin use in normal mode.

When the Function Button is pressed, the FR1438-2 menu is displayed in

sequence.

3 10, 119

68751, 2 4

14 15

CH Channel select mode (1-14)

ctc Coded Tone Controlled Squelch System Sub-Channel Select Mode

SC Auto Channel Scan Mode

dDual Channel Watch Mode

UO Voice Activated Function

Udt Voice Activated Recovery Time

ALO Auto Key Lock Selection Mode

CAL Call Ringer Melody Selection Mode

ton Sub-Channel Number or Sub-Channel Frequency

15. Small Segment Display: Displays the CTCSS tone option in the normal mode.

The CTCSS option is shown in Hz.

When the Function Button is pressed, the FR1438-2 selection of each menu is

displayed in the following sequence and format.

(1 through 14) (CH) Channel Number

(1 through 38 or Frequency, OFF) (cTc) Sub-Channel Frequency in Hertz or

Number

(Up, Down, OFF) (SC) Auto Channel Scan Mode

(Channel Number 1 through 14, OFF) (d ) Dual Channel Watch Mode

(High,Off, Low) (UO) Voice Activated Function

(Choice of 5,3,2,1 seconds) (Udt) Voice Recovery Activated Time

(Off, Auto) (ALO) Auto Key Lock Selection Mode

(1 Through 7) (CAL) Call Ringer Melody Selection

(Number) or (Hertz) (ton) Sub-Channel Frequency (Number = no,

Frequency = Freq)

Powering the transceiver:

Your FR1438-2 radio transceiver operates on four AAA batteries . You may operate

your FR1438-2 using the rechargeable batteries included or you may use alkaline

batteries. Alkaline batteries will provide slightly better performance than the

rechargeable batteries, but must never be recharged in the charging stand.

Installing the batteries:

To install batteries into the radio, it is necessary to remove the belt clip. To do this you

will need to release the spring clip securing the belt clip to radio and lift the belt clip

away from the radio body. Next, remove the battery compartment cover by sliding it

downward towards the bottom of the transceiver. Observe the polarity symbols on

the bottom of the tray when inserting the batteries. Replace the cover.

1.Press the spring clip

and slide the belt clip

upwards.

2. Slide the battery cover

downward. 3. Insertbatteriesobserving

the polarity symbols on

the bottom of the tray.

Thefollowing guidelineswill improve performance and provide longer operating times

for the FR1438-2:

1. Do not mix old and new batteries.

2. The use of alkaline-type batteries is recommended to provide the longest operating

time.

3. Do not mix alkaline, standard (carbon-zinc) or rechargeable (Ni-MH) batteries.

4. If the unit is not to be used for an extended period of time, remove the batteries. Old

or leaking batteries can cause damage to the unit and will void the warranty.

Wrist Strap and Detachable Belt Clip Installation

The wrist strap and detachable belt clip are provided to enable you to carry the FR1438-2

easily and safely. The wrist strap can be attached to the hole located on the top of the

belt clip. Feed the small loop on the end of the strap through the hole and then pass

the strap through the loop and pull tight.

The detachable belt clip fits into the slot located on the rear of the unit. To remove the

belt clip, press the locking clip at the top of the belt clip away from the unit and slide

the belt clip upwards. To install the belt clip slide it down into the slot and snap in to

place.

AAA

SIZE

AAA

BATTERY

COVER

SPRING

CLIP

Charging the FR1438-2:

Insert the charging transformer into a household electrical outlet and connect its

power jack to the socket on the rear of the charging stand. Simply placing the unit

into the charging stand will begin the charging process. The red LED on the front of

the charging transformer serves as a charge indicator. The charging stand will

charge two units simultaneously. Approximately 12 – 16 hours are required to fully

charge the batteries. Remember to turn your FR1438-2 OFF before placing it into

the charging stand.

Caution: The charging stand in your kit is intended for use with the supplied

batteries. Do not attempt to recharge any other batteries with the

charging stand.

Controls:

Power On/Off (13):

Press and hold this button for two seconds to turn the unit on. A short confirming

melody will sound. To turn the unit off, press and hold the button for a two-second

period. A short tone will sound before the unit shuts off.

Enter Button (13):

This button is also used to confirm options for operating modes during the function

edit mode. A momentary press of this button will convert the display of the CTCSS

subcode from a frequency to a number or number to a frequency for two seconds.

TRANSFORMER

CONNECTOR

RED LED

CHARGING

INDICATOR

CHARGING

STAND

CHARGING

TRANSFORMER

Push To Talk (PTT) Button (4):

Pressing and holding this button will allow you to speak to any transceiver that is set

to the same channel and privacy code setting as yours. Hold the transceiver

approximately 1 to 2 inches from your face as you speak into the built in microphone

(9). After you have finished speaking, release the PTT button to allow the reception

of incoming signals. It is not possible to transmit and receive at the same time. The

red transmit LED indicator located on the right side of the LCD Panel (8) will light

while the PTT button is pressed.

Releasing the button allows the unit to revert to standby mode. When receiving an

incoming signal, the green receive LED indicator on the left side of the LCD Panel (8)

will light.

The PTT button can also be used as a two-way call ringer. Pressing the button twice

quickly will call another party on the same channel. The word CALL and the transmit

icon will appear in the display. The user selected call will sound.

Volume Control (10 and 11):

In the standby mode, adjust the volume to a comfortable level by presing the Up (10)

to increase the volume level and the Down (11) to decrease the volume level.

Up Button (10):

In the standby mode, pressing this briefly will increase the volume. In the function

editmode,pressingthe button briefly will shiftfromthecurrent option in each submenu

to next option in the same submenu.

Pressing the button for more than 1.5 seconds allows navigation at a more rapid

rate. In the standby mode the volume will increase rapidly. In the function mode,

different menus can be rapidly accessed.

Down Button (11):

In the standby mode, pressing this briefly will decrease the volume. In the function

editmode,pressingthe button briefly will shiftfromthecurrent option in each submenu

to next previous option in the same submenu.

Pressing the button for more than 1.5 seconds allows navigation at a more rapid

rate. In the standby mode the volume will decrease rapidly. In the function mode,

different menus can be rapidly accessed.

Function Button (12):

In the standby mode, pressing this button briefly will enter the function edit mode.

Pressing the button for more than 1.5 seconds will activate or deactivate the KEY

LOCK when the unit is in the standby mode. Refer to KEY LOCK function description

to activate and deactivate the KEY LOCK.

NOTE: All buttons will be disabled except for the Monitor Button (2) and the

PTT Button (4).

Monitor Button (2):

The Monitor Button is used to check the activity on a channel before transmitting.

When the Monitor Button is pressed, the LCD panel (8) will light and both the transmit

andthereceiveindicators will light. PressingtheMonitorButton during theeditfunction

mode will return the unit to standby. Pressing the Monitor Button during a VOX

tranmission(voiceactivatedtransmission)will discontinue the transmissionanddisable

the VOX function for ten seconds.

External Microphone/Speaker (6):

This jack accepts an Audiovox FRS-BHST headset/microphone for totally hands free

operation.

Operating Modes and Features

Channel Select Mode:

This feature allows the selection of main channels for communication.

1. Press the Function Button (12) until CH appears in the LCD Panel (8).

2. Press the Up Button (10) or the Down Button (11) to choose the channel.

3. Press the Enter (13) to confirm your selection.

Coded Tone Controlled Squelch System (CTCSS):

When the CTCSS feature is on the transceiver will only receive signals from other

transceivers set to the same channel and privacy code. When the CTCSS mode is

off, the transceiver will receive signals from all transceivers set to the same channel.

Remember that the CTCSS feature does not prevent others from listening to your

transmissions. It only allows your FR1438-2 to ignore signals from transceivers not set

to the same privacy code.

1. Press the Function Button (12) until ctc appears in the LCD Panel (8).

2. Press theUpButton(10)ortheDownButton (11) to choosetheCTCSScodedesired.

3. Press the Enter (13) to confirm your selection.

NOTE: To communicate with other units, they must be switched to the same

channel and CTCSS subcode. To communicate with other units that

do not have subcodes, switch your unit to the same channel with the

subcode set to Off.

AUTO CHANNEL SCAN MODE:

This feature allows scanning for an active channel. The volume cannot be adjusted

and the power saver is disabled in this mode. To access the Auto Channel Scan

menu:

1. Press the Function Button (I 2) until the auto channel icon blinks and SC appears

in the LCD Panel (8).

2. Press the Up Button (10) or the Down Button (11) to choose scanning up or

down from the current channel number.

3. Press the Enter Button (I 3) to confirm your selection.

The unit will begin scanning for an active main channel. If a transmission is

detected, the Receive and RSSI icons will appear in the LCD Panel (8). To turn off

the auto channel scan feature in the standby mode, simply press the Function

Button (12) once. You can pause on any channel while in the Auto Channel Scan

Mode by pressing the PTT Button (4) during the reception of a signal for 5 seconds

afterward. Pressing the Monitor Button (2) will resume scanning and eliminate that

channel from those being scanned.

DUAL WATCH SCAN MODE

This feature allows the monitoring of two different channels at the same time. If any

priority channel other than the current channel in use is preset, the preset channel

will be scanned every 0.5 second and you will signaled when a call is received.

While in the Dual Watch Scan Mode you may hear transmissions from either a

primary or secondary channel when transmitting. The unit will always transmit on

the primary channel unless the PTT Button (4) is pressed during or immediately

following the reception of secondary channel transmission. The power saver mode

is disabled in the Dual Watch Scan Mode and the volume is not adjustable. To

access the Dual Watch Scan menu:

1. Press the Function Button (12) until the dual watch icon blinks and dappears in

the LCD Panel (8).

2. Press the Up Button (10) or the Down Button (II) to select the desired channel

number you wish to monitor.

3. Press the Enter Button (13) to confirm your selection.

To turn off the dual watch feature in the standby mode, simply press the Function

Button (12) once.

VOX SELECTION MODE

The Voice Activated Transmission (VOX) function allows your voice to activate signal

transmissionautomatically when the FR1438-2 is used with a handsfree microphone/

headset (FRS-BHST). It also allows hands free use when a microphone/headset is

not being used without having to use the PTT Button (4). When in the VOX mode a

short beep will sound after the termination of any VOX generated transmission. To

access the VOX Selection menu:

1. Press the Function Button (12) until the VOX icon blinks and UO appears in the

LCD Panel (8).

2. Press the Up Button (10) or the Down Button (11) to select from high, low or off.

The high or low setting determines VOX response sensitivity.

3. Press the Enter Button (13) to confirm your selection.

VOX RECOVERY TIME SELECTION MODE

This allows the setting of the transmit delay after you have finished speaking.

To access the VOX Recovery Time Selection menu:

1. Press the Function Button (12) until Udt appears in the LCD Panel (8) with

the VOX icon blinking.

2.Press the Up Button (10) or the Down Button (11) to select from the 5, 3, 2

or 1 second setting. This setting determines the delay time between

transmitting and receiving.

3.Press the Enter Button (13) to confirm your selection.

NOTE: You may need to try different VOX time settings to determine

the best value to suit your speaking habits.

Toturn offthe VOX feature, enter the VOXselectionmodeand

thenselectOFF.

AUTO KEY LOCK SELECTION MODE

This feature prevents accidental channel change and disturbance to the preferred

settings of the FR1438-2. The Auto Key Lock feature temporarily disables the Up,

Down and Enter Buttons. To access the Auto Key Lock Selection menu:

1. Press the Function Button (12) until the auto lock icon blinks and ALO

appears in the LCD panel (8).

Otros manuales para FR-1438-2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Radio bidireccional de Audiovox

Audiovox

Audiovox FR548-2CH Manual de usuario

Audiovox

Audiovox 128-7031 Manual de usuario

Audiovox

Audiovox GMRS9010-2 Manual de usuario

Audiovox

Audiovox FR-531-2 Manual de usuario

Audiovox

Audiovox GMRS200W Manual de usuario

Audiovox

Audiovox FR-1438-2 Manual de usuario

Audiovox

Audiovox GMRS3082CH Manual de usuario

Audiovox

Audiovox FRS-WP1 Manual de usuario

Audiovox

Audiovox FR-142B Manual de usuario

Audiovox

Audiovox FR530 - Ultra Compact 14 Channel LCD Radios Manual de usuario

Audiovox

Audiovox GMRS122-2 Manual de usuario

Audiovox

Audiovox FRS1000 - FRS Base Station Manual de usuario

Audiovox

Audiovox FR-500 Manual de usuario

Audiovox

Audiovox FR-540 Manual de usuario

Audiovox

Audiovox FR-100 Manual de usuario

Audiovox

Audiovox Rampage AXT-240 Manual de usuario

Audiovox

Audiovox FR-560FM Manual de usuario

Audiovox

Audiovox FR-140 Manual de usuario

Audiovox

Audiovox FR-140 Manual de usuario

Audiovox

Audiovox FR-541 Manual de usuario

Audiovox

Audiovox FR-1400 Manual de usuario

Audiovox

Audiovox FR-1438-2 Manual de usuario

Audiovox

Audiovox FR-114-2 Manual de usuario

Audiovox

Audiovox 128-5377 Manual de usuario

Manuales populares de Radio bidireccional de otras marcas

Midland

Midland 70-1526A/B Manual de usuario

HYT

HYT TC700 Manual de usuario

DNT

DNT Space100 Manual de usuario

Legacy

Legacy ProLine Series Manual de usuario

Evolveo

Evolveo FreeTalk XM2-2 Manual de usuario

AWC

AWC AWR1688+ Manual de usuario

Motorola

Motorola XT665d Manual de usuario

Cobra

Cobra 2-Way Radio Manual de usuario

Klutch

Klutch KR-400 Manual de usuario

Garmin

Garmin Rino 655t Manual de usuario

Motorola

Motorola TLK 150 Manual de usuario

Midland

Midland MXT275J Manual de usuario

Titan

Titan TR200 Manual de usuario

Cobra

Cobra CXT645 Manual de usuario

Tait

Tait TM9100 Manual de usuario

Yaesu

Yaesu FT-65R Manual de usuario

RELM

RELM RP3000 Manual de usuario

Motorola

Motorola ASTRO SRX 2200 Series Manual de usuario