Audiovox ADDP1 Instrucciones de funcionamiento

~AUDIOTOX~

~CORPORATION

Model

ADDP1 ADDSS

Install Transmitter

Programming Guide

THE RECEIVER/ANTENNA /PUSH-BUTTON/LED ASSEMBLY:

The Superheterodyne Receiver Antenna Assembly provided with this ADD unit allows rout-

ing from below the dash board for maximum operating range. Choose a location above the

belt line (dashboard) of the vehicle for best reception. Special considerations must be made

for windshield glass as some newer vehicles utilize a metallic shielded window glass that

will inhibit or restrict RF reception. In these vehicles, route the antenna toward a rear

window location for best reception. Secure the antenna with double stick tape provided.

After securing the antenna with tape, we advise also securing a section of the antenna

cable to a fixed support. This will prevent the antenna from dropping down in case the

double stick tape is exposed to extreme heat which may loosen it's gummed surface. Route

the 3 connectors to the control module using caution not to route too close to any hot or

moving parts like the steering wheel shaft.

At this point you and or the owner has three options:

a) Leave the already installed push-button LED as is for override/programming and visual

indications, and use only the receiver portion of the ADD receiver.

b) Disconnect the already installed push-button LED switch and use this ADD receiver in it's

place for override/programming, and visual indications.

c) Connect both the ADD receiver along with the existing push-button LED switch where the

owner can use either one or the other both for programming

override functions

and both as visual indications.

(a) Just plug in the 3 pin black connector of the ADD receiver.

(b) Unplug the White

Blue 2 pin LED, and ValeVOverride connectors for the existing

push-button switch and connect all three connectors of the ADD receiver.

to the blue wire on the existing push-button switch, and splice the grey wire of the

ADD receiver to the grey wire of the existing push-button switch.

In scenario a, the existing push-button switch will function as it always did and the receiver

will communicate with the transmitter once programmed.

in scenario b, the push-button and LED on the receiver will replace the functions of the

existing push-button LED switch, the receiver will communicate with the transmitter once

programmed.

In scenario c, both the existing push-button LED switch will continue work as it did, as well,

the push-button switch and LED on the ADD receiver will duplicate these functions. The

receiver will communicate with the transmitter once programmed .

•....

"' l. ADD Kit

--~~~~1i: ~:

Front Window Mount

7 /, A Iiil ~

Antenna/Receiver

'- ".0

i~~

128-8972

•

B TIERY REPL CEMENT

Your one button transmitter, which has a part number listed on the back cover, includes a

battery that will need to be replaced from time to time. Use GP27a for the S1 BTXA, or

CR2032 for the 091 BPr. If you notice diminished range, or if the LED on the transmitter lights

dimly, the battery should be replaced. To do so:

1) Remove the 0 point philips head screw found at the lower portion in the rear of the case

of the S1 BTXA transmitter, or the two 0 point philips head screws found at the lower portion

in the rear of the case 091 BPr transmitter.

2) Carefully separate the two transmitter case halves.

3) Remove the battery noting the proper orientation/polarity of the battery. Properly dispose

of the discharged battery.

4) Install the new battery being certain to correctly arrange the positive and negative poles.

5) Carefully close the case halves, finish by reinstalling the screw or screws removed in

step 1.

See Drawings Below:

(

Start Button

I ;~11

§OPoinl

Philips

screw

\I~

r'-Ii

Programming The Transmitters:

After completing the installstion of the ADD receiver:

I) Turn the ignition to the ON position.

2) Press and release the Override/Programming switch 3 times, note the LED blinking IX

pause, IX pause, etc.;

3) Press and hold the start push-button on the transmitter until the parking lights flash and

or the horn beeps. This confirms the transmitter has been learned.

Repeate step 3 for each transmitter being programmed. The unit will accept up to 4

transmitters.

4) Turn the ignition switch off.

Test your unit by pressing the transmitter push-button 2 times in succession.i.the vehicle

should start.

Note: The vehicle factory transmitter will also start the vehicle as before, however, the new

I button transmitter will function at a significately increased range over the factory

transmitter.

128-8972

•

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transmisor de Audiovox

Audiovox

Audiovox PRO94BT3 Instrucciones de funcionamiento

Audiovox

Audiovox AVX01BT3CL3 Instrucciones de funcionamiento

Audiovox

Audiovox PRO-94FR Instrucciones de funcionamiento

Audiovox

Audiovox Pursuit PRO-OE2 Instrucciones de funcionamiento

Audiovox

Audiovox PRO-OE3B370 Instrucciones de funcionamiento

Audiovox

Audiovox Prestige 103BP Instrucciones de funcionamiento

Audiovox

Audiovox Prestige 105BP Instrucciones de funcionamiento

Audiovox

Audiovox AA-99BT2 Instrucciones de funcionamiento

Audiovox

Audiovox Prestige 101BP Manual del propietario

Audiovox

Audiovox Pursuit PRO-OE3 Instrucciones de funcionamiento

Audiovox

Audiovox AA-95BT3S Instrucciones de funcionamiento

Audiovox

Audiovox Pursuit PRO-OE3B3 Instrucciones de funcionamiento

Audiovox

Audiovox PRO92BTINT Instrucciones de funcionamiento

Audiovox

Audiovox Pursuit PRO-OE4 Instrucciones de funcionamiento

Audiovox

Audiovox PurSuit 08SPr Instrucciones de funcionamiento

Audiovox

Audiovox AA923-AA94BT Manual del propietario

Audiovox

Audiovox PurSuit 091BPr Instrucciones de funcionamiento

Audiovox

Audiovox Pursuit OE3-FT3 Instrucciones de funcionamiento

Audiovox

Audiovox APS 95 BT3S Instrucciones de funcionamiento

Audiovox

Audiovox PRO94BT2 Instrucciones de funcionamiento

Audiovox

Audiovox AUTO SECURITY Prestige OE3B4 Instrucciones de funcionamiento

Audiovox

Audiovox PurSuit 09XR1Pr Instrucciones de funcionamiento

Audiovox

Audiovox Prestige APS-2K4 Instrucciones de funcionamiento

Audiovox

Audiovox Pursuit PRO-OE2B Instrucciones de funcionamiento

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario