Audiovox LCM5043NP Instrucciones de instalación

LCM5043NP & LCM5643NP

Remote Controlled Color Display Monitor

with Headphone Jack

Installation and Owner's Manual

ELECTRONICS COR

EXPLANATION OF GRAPHIC SYMBOLS

WARNING:

TOPREVENTFIRE ORELECTRICSHOCK HAZARD,DONOTEXPOSE

THISPRODUCT TORAIN ORMOISTURE.

CAUTION:

1. This product is designed to operate with a 12 volt, negative ground bat-

tery system.

2. Disconnect the ground wire from the battery terminal before connecting

the electrical system. Refer to the electrical connection diagram to avoid

wrong connection of the electrical system.

Always use authorized service center for service assistance.

3. Do not operate the monitor at temperatures below 32°F (0°C) or above

104°F (40°C).

4. Keep the monitor clean and dry.

5. Never attempt your own repairs. This unit should be installed and re-

paired by qualified technicians or service personnel..

6. Do not drop the monitor or expose to strong impacts.

7. Do not expose to direct sunlight for extended periods of time.

8. Use proper insulation material to prevent short-circuiting of the supply

system.

9. Tighten all loose wires after installation.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO

NOT REMOVE COVER (OR BACK) NO SERVICEABLE PARTS

INSIDE REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with the arrowhead within a triangle is in-

tended to alert tell the user that parts inside the product are

capable of producing an electric shock .

The exclamation point within a triangle is intended to alert the

user that important operating and servicing instructions are

being provided.

SYSTEM OVERVIEW

TheLCM5043NPiscomprisedofa 5"ThinFilmTransistor(TFT)Liq-

uidCrystalDisplay(LCD)Monitor. TheLCM5643NPiscomprisedofa

5.6"ThinFilm Transistor(TFT)LiquidCrystalDisplay ( LCD)Monitor.

TheMonitorforbothofthesesystemshavea4:3AspectRatiodisplay

that allows the user to select between two video sources (Not Sup-

plied). TheMonitorsdisplays allfunctionswiththecomprehensive On

Screen Display (OSD). Can be used with an optional Wired Head-

phone.

OPTIONAL AUDIO CONNECTION

1) WiredHeadphones......................................... P/N=HP275

Wired Headphones

MATERIALS LIST

1. System Monitor (LCM5043NP=136C2187) or (LCM5643NP=136C2186) (1pc.)

2. Remote Control Unit (136B2156) with Lithium Battery, 3V,CR 2025 (1pc.)

3. Interconnect Box (136B2183) (1pc.)

4. Monitor Cable, 8' (112B3152) (1pc.)

5. Headrest Mounting Tray (LCM5043NP=102C3740)

or(LCM5643NP=102C3742) (1pc.)

6. Trim Ring for Mounting Tray (LCM5043NP=102B3741)

or(LCM5643NP=102B3743) (1pc.)

7. Power Cable, 2.46' (112B3127) (1pc.)

8. Removal Tool (108B3632) (1pc.)

 !

%&'

VEHICLE PREPARATION

1) Decide on the system configuration and the options that will be in-

stalled (i.e.whatcomponents, VCP,DVD, TV Tuner,VideoGame,

Monitor,FMModulator,etc.).

2) Read the manuals and get familiar with the electrical requirements

andconnections.

3) Decideonthemountinglocationsandmethodsofmountingtheprod-

ucts.

4) Preparethevehicle by removing anyinteriortrimnecessary to gain

accesstothevehicle'swiringaswellasallareaswhereinterconnect-

ingwireharnesseswillbelocated.Ifanyaccessholesneedtobecut

intothevehicle,headrests,orothertrimcomponents,thisshouldbe

performednow.(RefertotheInstallationProcedure).

5) Runthewiringharnessesandcablingthroughoutthevehicleasnec-

essary.(Refertothewiringinstructionsfortheindividualcomponents

andaccessoryoptionsbeinginstalled).Besure,thatallthewiringis

protectedfromsharpedgesandisroutedinsuchamannerthatitwill

not be pinched, when it is fully installed. Be sure to leave enough

slack in the wiring at each component to allow sufficient working

room.

6) Remove all the A/V system components from their packaging and

thenplacetheminthevehicleattheirrespectivelocations.

7) Locateanaccessorypowersource(RedWire)(+12VDCpresentwhen

theignition keyis in the accessory and run positions. 0VDC should

bepresent,whentheignitionkeyis in the OFF position). Generally,

thesewirescanbefoundattheignitionswitchor fuse box.

8) LocateaConstantPowerSource(YellowWire)(+12VDCpresentat

all times).

NOTE: Ensure that the accessory power is fused at the source.

Failure to do so may result in vehicle wiring damage.) Ground the

blackwire toa chassis ground close to the mounting location of AV

sources.

9) Connectallthecomponentstogether(electrically)andverifythatthe

proper operation of all the system functions. NOTE: This is best

doneBEFOREthecomponentsarepermanentlymounted.

10) Afterverifyingtheproperoperationofthesystem,proceedtomount

eachcomponent.

11) The mounting method, and the location will vary from vehicle to

vehicle, so this manual will only focus for the installation of the

12) The best location for the system components is:

a)Monitor:Headrestorbracket(optional)mountedontoaflat

surface.

b) System Interconnection Box (AVX-6869): In line with all

the system cabling and in an area were it can be easily ac-

cessed.

c)SystemMain Cable: Undereitherseat where monitors

arelocated.

Tools and Materials Required:

Utility knife or box cutter with sharp blade.

PermanentMarker.

TieWraps.

INSTALLATION

OptionalBracket Mounting:

This procedure describes mounting the system monitor using an op-

tionalSurface MountBracket (sold separately,#FB1)

1) Start by firmly attaching the Surface Mount Bracket onto a flat

surface

IMPORTANTNOTICE

It is unlawful in most jurisdictions to drive a motor vehicle which is

equipped with a television viewer or screen that is located at the point

forward of the back of the driver’s seat, or that is visible directly or indi-

rectly, to the driver while operating the vehicle.

3) Adjust viewing angle of monitor by tightening the fastener at the

side.

4) When the system components are mounted, test the system to

verifythatit isfunctioningcorrectly. Makesurethatnowiringwas

pinched,orconnectedimproperly duringthefinalinstallation.

Surface Mount

MountingBracket

FastenerWheel

Monitor

2) Slide monitor onto Surface Mount Bracket and then tighten the

fasten wheel.

SurfaceMountFastener

1) Removetheheadrestfromthe

vehicleforeasiestinstallation.

2) Layheadrestonaflatsurface.

3) Center trim collar on headrest

asshown.

NOTE: Depending on the angle of

the headrest the Trim Ring and

housing may be mounted upside

down.

4) Using a Permanent Marker,

mark headrest material along

theinteriorofthe TrimRing.

5) Remove the Trim Ring and

markan“X”fromcornertocor-

nerasshown.

Headrest Mounting:

Monitor Mounting

Tray Trim

Ring Headrest

9) Usingyourfingers,tearthefoam

out of the headrest leaving a re-

cess where the shell will be in-

serted.

NOTE: At this point you will need to

installtheharnessupthroughthearea

into the recess. It may be helpful to

followoneofthepostsandtiewrapit

to the post for restraint.

6) Using the utility knife, cut the

headrest material along the “X”

lines. Do not cut the material

alongthe other lines at this time.

7) Thiswillleaveyouwithan“X”cut

asshown.

8) Pulltheflapsupandcutthefoam

beneaththematerialtotheproper

depth. Cut all four sides of the

foam.

11) Guidethecablethroughtheside

openingoftheMountingTrayand

plug it into the Monitor. Make

sure the connector locks into

place. InserttheMonitorintothe

Mounting Tray and secure the

cable using tie wraps or screws

12) Turn the Monitor around and in-

sert it into the Mounting Tray

housing. Snap into place.

10) Lay the flaps of headrest mate-

rialdownintotherecess and in-

sert the Mounting Tray into the

recess. Check for fit. If it does

notfitproperly,you mayneedto

removesomemorefoam.

NOTE:TheMountingTraywill need

tobesecuredtothe headrest,either

by using tie straps, screws, ect..

13) ConnecttheMonitorpowerinput

plugtoaDCpowersource(Red

plug+12 VDC, Yellowplug +12

VDCConstantandBlackplug(-)

toground).

14) Connect the external video

sourceoutputsignal(fromVCP/

DVD, TV Etc.) to the VIDEO IN

jack. Test the system to verify

properinstallation.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Monitor de Audiovox

Audiovox

Audiovox LCM50 Manual de usuario

Audiovox

Audiovox AVX10USB Manual de usuario

Audiovox

Audiovox VOH1012 S Manual de usuario

Audiovox

Audiovox LCM-4000 Manual de usuario

Audiovox

Audiovox LCM1700TV Manual de usuario

Audiovox

Audiovox LCM-0565 Manual de usuario

Audiovox

Audiovox MZ7TFT Manual de usuario

Audiovox

Audiovox LCM-5600NP Manual de usuario

Audiovox

Audiovox MZ7TFT Manual de usuario

Audiovox

Audiovox D1909 - DVD Player - 9 Manual de usuario

Audiovox

Audiovox LCM45NB Manual de usuario

Audiovox

Audiovox VBPEX5 Manual de usuario

Audiovox

Audiovox LCM-5600 Manual de usuario

Audiovox

Audiovox GMRS1100 Manual de usuario

Audiovox

Audiovox AVM6781 Manual de usuario

Audiovox

Audiovox LCM5869NP Instrucciones de instalación

Audiovox

Audiovox AVXMTG10U Manual de usuario

Audiovox

Audiovox AOM561 Manual de usuario

Audiovox

Audiovox EX50 Manual de usuario

Audiovox

Audiovox Movies2Go AVXMTGHR1D Manual de usuario

Audiovox

Audiovox ACAM250 Manual de instrucciones

Audiovox

Audiovox LCM45NB - LCM 45NB - LCD Monitor Manual de usuario

Audiovox

Audiovox AOM562A Manual de instrucciones

Audiovox

Audiovox Eddie Bauer PE703 Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación