AudioCodes MediaPack 1 Series Manual de usuario

1 |Page

MediaPack™ 1xx Analog VoIP Gateway

Quick Setup Guide

Welcome

Congratulations on purchasing your AudioCodes MediaPack 1xx (MP-1xx) Analog Voice-over-IP (VoIP) Media

Gateway (hereafter, referred to as device)!

This document is only intended to provide basic setup instructions for initial access to the device and

connecting it to your network. For advanced configuration and cabling, refer to the User's Manual and

Hardware Manual respectively, which can be downloaded from AudioCodes Website at

https://www.audiocodes.com/library/technical-documents.

Before you begin, please read the Safety Precautions on page 9.

Package Contents

Make sure that the following items (in addition to any separate-orderable items that you may have purchased)

are included with your shipped device:

4 x anti-slide bumpers for desktop mounting

1 x AC power cable

Regulatory Information document

This document

2 |Page

Physical Description

[The presence and number of FXS and FXO port interfaces depends on ordered MP-1xx model.]

100-240V

AC power plug entry.

Power LED (located on front panel):

Green On

Power received by device

Off

No power

Ready LED (located on front panel):

Green On

Device is powered up

Off

Installing software (.cmp file) or device failure

Fail LED (located on front panel):

Red On

Device failure or initializing

Off

Normal operation

Ethernet

10/100Base-T Ethernet port (RJ-45) for connecting to the IP network.

Uplink LED (located on front panel):

Green On

Ethernet link established

Green Flashing

Data is being received or transmitted

Off

No Ethernet link

RS-232

RS-232 serial interface port (6-pin mini-DIN female - PS/2).

Note: MP-112 does not provide a serial port.

FXS and/or

FXO

Foreign eXchange Subscriber (FXS) ports (RJ-11) and/or Foreign eXchange Office

(FXO) ports (RJ-11). The number and type of ports depends on ordered MP-11x

model.

Channels Status LED (located on front panel):

Green On

Phone is in off-hook position

Green Slow-Flashing

Phone is ringing

Green Fast-Flashing

Malfunction

Off

Phone is in on-hook position

Reset

Reset pinhole button for resetting the device or restoring it to factory defaults. To

restore the device to factory defaults: Disconnect the Ethernet cable and then

with a paper clip or any other similar pointed object, press and hold down the

button for about six seconds.

3 |Page

Mounting the Device

You can mount the device on a desktop using the four anti-slide bumpers (supplied), which you need to stick in

the grooves (shown below) located on the underside of the device.

You can also mount the device on a wall or in a standard 19-inch rack. For instructions on wall mounting and

19-inch rack mounting, refer to the Hardware Manual

4 |Page

Power Cabling the Device

The device is powered from a standard alternating current (AC) electrical wall outlet, using the supplied power

cord.

1. Insert the female connector located on the end of the power cord (supplied) into the device's power

socket located on the rear panel.

2. Insert the male plug located on the other end of the power cord into a standard electrical wall outlet.

The Power LED (located on the front panel) is lit green, indicating that the device is receiving power.

5 |Page

Assigning an IP Address to the Device

The default IP address depends on your MP-1xx model:

FXS-only models and FXS-with-FXO models: 10.1.10.10

FXO-only models: 10.1.10.11

For all MP-1xx models, the default subnet mask is 255.255.0.0 and the Default Gateway IP address is 0.0.0.0.

You can change the IP address using any of the following methods:

Accessing the device's Web-based management interface from a computer using the default IP address

Accessing the device's interactive voice response (IVR) menu, using touch-tone dialing (DTMF tones) on

a standard telephone connected to one of the device's FXS ports

ASSIGNING AN IP ADDRESS THROUGH THE WEB-BASED MANAGEMENT INTERFACE

Use the device's factory default IP address to initially access the device's Web-based management interface

and then change it to suit your network addressing scheme for subsequent connectivity.

1. Using a crossover RJ-45 Ethernet cable, connect the device's Ethernet port located on the rear panel

and labeled Ethernet, to the LAN port of your computer.

2. Change the IP address of your computer to correspond with the device's default IP address and subnet

mask.

6 |Page

3. On your computer, open a standard Web browser (for example, Google Chrome), and then in the URL

field, enter the device's default IP address; the Web Login screen appears:

4. Type in the default username (Admin) and password (Admin), and then click Login.

5. Open the IP Settings table (Configuration tab > VoIP menu > Network > IP Interfaces Table).

6. Modify the IP address to suit your network addressing scheme:

In the 'IP Address' field, enter the new IPv4 IP address in dotted-decimal notation.

In the 'Subnet Mask' field, enter the new subnet mask in dotted-decimal notation.

In the 'Default Gateway Address' field, enter the new IP address of the Default Gateway in dotted-

decimal notation.

7. Click Submit to apply your settings.

7 |Page

8. Open the Maintenance Actions page (Maintenance tab > Maintenance menu > Maintenance Actions),

and then click BURN to save your settings to the device's flash memory. This process also causes the

device to reset.

As you have changed the device's IP address, your connection to the device's management interface

through your browser is no longer available.

9. Disconnect the device's Ethernet cable from your computer and then connect it to your network.

10. Access the device's management interface using the device's new IP address.

8 |Page

ASSIGNING AN IP ADDRESS THROUGH THE VOICE MENU

You can change the IP address through the device's interactive voice response (IVR) menu, using touch-tone

dialing (DTMF tones) on a standard telephone that is connected to one of the device's FXS ports:

1. Connect a telephone to one of the device's FXS ports.

2. Lift the handset off the hook, and then dial ***12345 (three stars followed by the digits 1, 2, 3, 4, and

5). Note that you may hear a fast-busy dial tone when pressing the * key.

3. When you hear the configuration menu voice prompt, continue with the next step.

4. To change the IP address:

a. Press 1followed by the number key (#); the current IP address of the device is played.

b. Press the #key.

c. Dial the new IP address, using the *key to denote the dots between digits (e.g., 192*168*0*4),

and then press #to finish.

d. Press 1to save.

5. To change the subnet mask:

a. Press 2followed by the #key; the current subnet mask of the device is played.

b. Press the #key.

c. Dial the new subnet mask (e.g., 255*255*0*0), and then press #to finish.

d. Press 1to save.

6. To change the Default Gateway IP address:

a. Press 3followed by the #key; the current Default Gateway address is played.

b. Press the #key.

c. Dial the new Default Gateway address (e.g., 192*168*0*1), and then press # to finish.

d. Press 1to save.

7. Hang up (on-hook) the telephone's handset.

9 |Page

Safety Precautions

This device is an indoor unit and therefore, must not be installed outdoors.

Ethernet cabling must be routed only indoors and must not exit the building.

The device must be installed and serviced only by qualified service personnel.

Do not open or dismantle the device.

Do not expose the device to water or moisture.

Make sure the device is installed in a well-ventilated location to avoid over heating of internal

components and subsequent damage.

Do not place any object on top of the device and make sure that sufficient clearance from the top and

sides are maintained to ensure proper airflow to avoid over heating of internal components.

Operate the device in an ambient temperature (Tma) that does not exceed 40°C (104°F).

The device must be installed only in restricted access locations.

Use only the supplied AC power cord for connection to the power source.

Installation of the device must be in accordance with national electrical codes and conform to local

regulations.

Ensure that you connect the device to an electrical socket outlet that provides protective earthing

(grounding).

The device is immune against power surge levels of up to 1 Kilovolts (KV) as required by the following

standards: IEC 61000-4-5, EN 55024, and EN 300386. Power surges above protection levels as required

by EN 55024 and EN 300386 may cause damage to the device.

For FXS ports, the device provides only Secondary Protection against power surges. In deployments

where the telephone lines are installed outside, you must install AudioCodes’ approved surge protector

(Circa model 4B3S-75) as the primary protection against lightning and other over-voltages phenomena

which might couple the 2-wire.

For FXO ports, use minimum 26-AWG wiring.

For FXX ports, use minimum 26-AWG wiring if it exits the building.

10 |Page

About AudioCodes

AudioCodes Ltd. (NasdaqGS: AUDC) is a leading vendor of advanced voice networking and media processing

solutions for the digital workplace. With a commitment to the human voice deeply embedded in its DNA,

AudioCodes enables enterprises and service providers to build and operate all-IP voice networks for unified

communications, contact centers and hosted business services. AudioCodes’ wide range of innovative products,

solutions and services are used by large multinational enterprises and leading tier one operators worldwide.

International Headquarters

1 Hayarden Street,

Airport City

Lod 7019900, Israel

Tel: +972-3-976-4000

Fax: +972-3-976-4040

AudioCodes Inc.

27 World’s Fair Drive,

Somerset, NJ 08873

Tel: +1-732-469-0880

Fax: +1-732-469-2298

Website: https://www.audiocodes.com/

What’s Inside Matters, OSN, SmartTAP, User Management Pack, VMAS, VoIPerfect, VoIPerfectHD, Your Gateway To VoIP,

3GX, VocaNom, AudioCodes One Voice and CloudBond are trademarks or registered trademarks of AudioCodes Limited. All

other products or trademarks are property of their respective owners. Product specifications are subject to change without

notice.

Date Published: 26 April 2018

Document #: LTRT-52913

Otros manuales para MediaPack 1 Series

Tabla de contenidos

Otros manuales de Puerta de AudioCodes

AudioCodes

AudioCodes mediapack MP-500 Manual de usuario

AudioCodes

AudioCodes MP-11x Fast Track Manual de usuario

AudioCodes

AudioCodes MediaPack MP-124 Manual de usuario

AudioCodes

AudioCodes Mediant 1000 Manual de usuario

AudioCodes

AudioCodes Mediant 2000 Manual de usuario

AudioCodes

AudioCodes Mediant 800 MSBG Manual de instrucciones

AudioCodes

AudioCodes Mediant 800B Instrucciones de montaje

AudioCodes

AudioCodes MP-252 Manual de usuario

AudioCodes

AudioCodes Mediant 4000 SBC Manual de usuario

AudioCodes

AudioCodes Mediant 1000 Manual de usuario

AudioCodes

AudioCodes MediaPack Manual de usuario

AudioCodes

AudioCodes MediaPack 124 Manual de usuario

AudioCodes

AudioCodes MP-204 Manual de usuario

AudioCodes

AudioCodes Mediant 500 Manual de usuario

AudioCodes

AudioCodes MediaPack MP-124 Manual de usuario

AudioCodes

AudioCodes Mediant 500L MSBR Instrucciones de montaje

AudioCodes

AudioCodes MEDIAPACK VERSION 6.2 Cómo utilizar

AudioCodes

AudioCodes Mediant 3000 Manual de usuario

AudioCodes

AudioCodes Media Pack MP-11x Instrucciones de montaje

AudioCodes

AudioCodes MediaPack MP-262-DB Manual de usuario

AudioCodes

AudioCodes Mediant 3000 Instrucciones de montaje

AudioCodes

AudioCodes Mediant 800 MSBG Manual de usuario

AudioCodes

AudioCodes Mediant 2000 Manual de usuario

AudioCodes

AudioCodes Mediant 500 Manual de usuario

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario