AUDAC POW2 Manual de usuario

POW2

Installation Manual

www.audac.eu

Introduction

Matrix Power Amplifier Kit

The POW2 is a sixteen channel power amplifier kit which is an optional device to be

installed inside the R2 Multi-Zone Digital Audio Matrix and M2 Multi-Media Digital

Audio Mixer devices.

In their standard configuration, these matrix systems are equipped with 8 line level output

channels whereto the appropriate amplifiers for your application can be connected.

In combination with the POW2 Power amplifier kit, they can be turned into a powered

matrix system, delivering an amplified output signal in the same single housing. This

can be very useful for applications where no large power capacities are required and

the available rackspace is limited.

The POW2 consists of a 16 Channel (8 Stereo Channel) Class-D amplifier, delivering

a power of 60 Watt to every channel. In bridge mode an output power of 8 x 120 Watt

can be obtained.

The input signal is internal linked from the DSP output and the output connections are

provided on the rear panel of the matrix system and are performed by using 4-pin

Terminal block connectors allowing connections for separate or bridged output channels.

It features an advanced protection circuit which protects against DC malfunctioning, short

circuit, overheating and overload while a large heatsink and speed controlled ventilation

fan ensure a proper operation temperature is continuously maintained.

The POW2 Power amplifier kit includes the power amplifier module, a switching power

supply and all necessary connection and installation accessories to properly install the

kit inside the Matrix’s housing.

Installation precautions !

The installation of the Power Amplifier Kit unit may only be

performed by qualified technicians.

Incorrect installation can lead to permanent damage or incorrect

functioning of the equipment.

Package contents

- Power amplifier module

- Power supply unit with PFC

- Loudspeaker output cables 200 mm (8 pcs)

- Stereo shielded signal cable 420 mm (2 pcs)

- Stereo shielded signal cable 460 mm (2 pcs)

- Stereo shielded signal cable 500 mm (2 pcs)

- Stereo shielded signal cable 540 mm (2 pcs)

- Mute cable 400 mm

- Power cable set Red / Black / Yellow

- 2 x T4AL/250V Slow blow fuse

- 2 Large Ferrite core for SD/MMC connection flatcable

(one might be mounted on the Power supply already)

- 8 x 4-Pin Terminal block output connectors (5.08 mm)

- POW 2 Option Sticker

Installing

Mounting and connecting

Please note this manual is for both M2 and R2 Assembly.

Picture used in this documentation are for M2 and may differ from R2.

Step 1:

Make sure the Matrix system is powered off and the power inlet is

disconnected from the mains power.

Step 2:

Open the device housing by carefully removing the screws from the top panel of the

device.

Step 3:

For M2: Place one of the supplied ferrite cores around the flatcables coming from the

USB and SD/MMC board on the front panel of the device.

Step 4:

Amplifier channel layout

OUT

7 8654321

1 2 3 4 5 6 7 8

Attach the 8 loudspeaker output cables to the I/O board(s) of the system.

Depending of the kind of system (R2 or M2) the output board will be different. The

loudspeaker output cables should be connected to the large 4-pin connectors on the

bottom side of the I/O board(s).

Step 5:

Attach the 8 stereo shielded signal cables to the amplifier module. Mark the cables

to keep a clear overview of which cable is connected to which channel. The

corresponding cable length for each channel is described in the table below:

Cable lengths: 420 mm: Channels 4 & 5 500 mm: Channels 2 & 7

460 mm: Channels 3 & 6 540 mm: Channels 1 & 8

R2 IO board signal connections

1 3

Step 6:

Then place the amplifier inside the matrix housing and fix it by inserting and

tightening four screws from the housings bottom side.

Connect the loudspeaker cables coming from the I/O board to the provided connectors

on the amplifier module. Make sure each connector on the I/O board is connected in

sequential order to the corresponding connector on the amplifier module.

Connect the stereo shielded signal cables coming from the I/O board to the

corresponding connectors on the amplifier module.

Align the cables to facilitate the placing

of the amplifier module.

Use cable ties to hold the signal cables

together.

Signal cables will go under the

amplifier module whereas the output

cables remain at the back of the unit.

Make sure the right amplifier channel is connected to the corresponding connector on

the I/O board. The connectors on the I/O board of the R2 are marked with the number

of the corresponding channel.

Note: Remember for R2 the I/O board is different, so please make sure you connect

the right channels to each other:

1 3

Step 8:

Connect the mute (Anti plop) cable to the provided connector on the amplifier module

and the small power supply (PowerDSP).

Step 9:

Power Supply unit

Please check if the suppression coil is attached to the power cable.

If it isn’t, please attache the supplied suppression coil first.

Place the power supply unit with PFC inside the matrix housing and fix it by inserting

and tightening four screws from the housings bottom side.

Step 10:

Connect the mains (110V AC ~ 240 V AC) cable from the big power supply (Power

supply unit with PFC) to the provided connector on the small power supply

(PowerDSP). Make sure the included ferrite core is placed around these cables.

Step 11:

Connect the 28 Volts output (+28V, GND, -28V) of the big power supply to the

amplifier module.

Align the connected cables nicely and fasten them with Cable ties. Ensure the airflow

of the fan is not blocked by cables.

Tabla de contenidos

Otros manuales de Amplificador de AUDAC

AUDAC

AUDAC SMA Instrucciones de instalación

AUDAC

AUDAC Dante AMP203LO Manual de usuario

AUDAC

AUDAC SCP2 Series Manual de usuario

AUDAC

AUDAC CAP412 Instrucciones de instalación y funcionamiento

AUDAC

AUDAC R1 Instrucciones de instalación y funcionamiento

AUDAC

AUDAC PRE220 Manual de usuario

AUDAC

AUDAC AMP20 MK2 Manual de usuario

AUDAC

AUDAC D2 Manual de usuario

AUDAC

AUDAC DPA74 Instrucciones de instalación y funcionamiento

AUDAC

AUDAC CEP Series Manual de usuario

AUDAC

AUDAC CAP224 Manual de usuario

AUDAC

AUDAC CPA12 Instrucciones de instalación y funcionamiento

AUDAC

AUDAC PRE116 Manual de usuario

AUDAC

AUDAC DPA73 Instrucciones de instalación y funcionamiento

AUDAC

AUDAC PRE16 Instrucciones de instalación y funcionamiento

AUDAC

AUDAC COM12 Instrucciones de instalación y funcionamiento

AUDAC

AUDAC COM108 Manual de usuario

AUDAC

AUDAC CPA24 Instrucciones de instalación y funcionamiento

AUDAC

AUDAC AMP22 Manual de usuario

AUDAC

AUDAC vc2200 Manual de usuario

AUDAC

AUDAC SMA Series Manual de usuario

AUDAC

AUDAC EPA252 Manual de usuario

AUDAC

AUDAC D2 Instrucciones de instalación y funcionamiento

AUDAC

AUDAC PX110 Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario