ATUMTEK ATMR088 Manual de usuario
ATUMTEK Single Monitor
Gas Spring Desk Mount Stand
2-9KG
EACH
30
9 8
WARNING STATEMENTS
Warning
Prior to the installation of this product, the installation instruction must be read and
completely understood. Failure to do so may result in personal injury, property damage
or voiding of factory warranty.
Do not install on a structure that is prone to vibration, movement or chance of impact.
Reinforce the structure as required before installation. Don't use the product on particle
board.
Pay attention to the weight capacity of the mount. Exceeding the limitation can result in
function unworkable or even serious personal injury and property damage.
Never operate the mount if parts are missing or damaged. Contact your local service
center for warranty service.
Stand Base
Clamp Connector
C- Clamp
Long Bolt Attachment Plate
1
2
3
4
Long Bolt
Anti-slip Pad
Gas Spring Arm
5
6
7
PARTS INCLUDED
01
M8×16（×1） M6×10（×2） M5×10（×4） M4×10（×4）
（×4） 4MM（×1） 5MM（×1）
1（×1） 2（×1） 3（×1） 4（×1）
5（×1） 7（×1）6（×1）
ABCD
E F G
Step 1 Mount the Base on Desk
02
Desk Side Installation (Desk Thickness ≤ 8 cm.)
First install and fasten the clamp connector (2) under stand base (1) together, then stick anti-slip
pad (6) under them.
Now assembly the clamp connector with C- clamp (3) together. There are 2 positions to choose.
Finally mount the stand base on desk side and fasten it.
2
6
1
A
G
B
F
3
10-50mm
A
A
B
F
30-80mm
3
G
Step 2 Mount the Arm
OR
Desk Grommet/ Hole Installation (Desk Thickness ≤ 6 cm.)
For desk with grommet hole or hole, stick anti-slid pad under stand base, then attach PARTS (4)
and (5) together, finally fasten the bolt to mount the base on desk.
Mount gas spring arm on the base and tighten the screw to fasten monitor arm on stand base firmly.
03
5
The Hole Size: 10-60mm
G
4
6
F
Step 3 Install the Monitor on Gas Spring Arm
04
Install 2 screws (C/D) and washers (E) on the upper VESA mounting holes first.
* only half screw the screws on so that monitor can be hanged on VESA plate safely.
Then hang the monitor on arm and fasten the top 2 screws, finally install the lower 2 screws on firmly.
C/D
E
G
B
C/D E
G
A
NOTE:
1. Please avoid excessive tightening screws and damage the monitor.
2. If monitor mounting head is not in upright direction, install monitor on arm first, then rotate
monitor to upright direction.
3. Choose to use washers or not according to monitor.
E
1 : 2
Step 4 Adjust the Arm
Keep the arm in horizontal position, then use the hex wrench to adjust the height tension of the
gas spring arms, to ensure the arm can support different monitors horizontally at any position.
* Be sure to keep the arm in horizontal position during adjustment. Otherwise, it would be difficult
to adjust the mount.
NOTE:
Increase the tension in “+” direction if the arm automatically sags.
Decrease the tension in “-” direction if the arm automatically rises.
05
fall down
+
G
-
pop up
G
Step 5 Cable Management
Insert cables management covers on arm to hold cables.
Step 6 Adjust Flexibility and Free Rotation
If it’s too tight or too loose to rotate or tilt monitor, adjust the screws on monitor
mounting head to reduce or increase damping to enable free rotation.
06
G
①
②
②
①
360°
360°
180°
360°
+90°
-45°
m.me/atumtekproducts
OR
www.atumtek.com
OR
Contact us via Facebook Messenger (Recommended):
If you need help with this purchase, please do not hesitate to contact us.
If you find our product satisfactory,
please encourage us by sharing your user experience online.
Prolinx GmbH
Brehmstr.56, 40239 Duesseldorf Germany
EC REP
Syncwire UK Ltd
C/O Lai and Co.109 Portland Street, Manchester, M1 6N
UK REP
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
