Atmel ATSAMB11 BluSDK SMART Manual de usuario

ATSAMB11 BluSDK SMART

Find Me Profile - Getting Started Guide

USER GUIDE

Introduction

The Find Me Profile (FMP) defines the behavior when a button is pressed on one device to cause an

alerting signal on a peer device.

Features

Device Discovery and Disconnection

Pairing/Bonding

Find Me Alerts

Console Display

Atmel-42612A-ATSAMB11-BluSDK-SMART-Find-Me-Profile-Getting-Started-Guide_UserGuide_112015

ATSAMB11 BluSDK SMART –Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42612A-ATSAMB11-BluSDK-SMART-Find-Me-Profile-Getting-Started-Guide_UserGuide_112015

Table of Contents

1Purpose .....................................................................................................................3

2Demo Setup..................................................................................................................3

3Hardware Setup ...........................................................................................................3

4Find Me Target.............................................................................................................4

5Software Setup.............................................................................................................5

5.1 Installation Steps...................................................................................................................................5

5.2 Build Procedure.....................................................................................................................................5

6Console Logging .........................................................................................................7

7Running the Demo.......................................................................................................8

8BluSDK SMART Software Architecture....................................................................11

9ATMEL EVALUATION BOARD/KIT IMPORTANT NOTICE AND DISCLAIMER........12

10 Revision History ........................................................................................................13

ATSAMB11 BluSDK SMART –Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42612A-ATSAMB11-BluSDK-SMART-Find-Me-Profile-Getting-Started-Guide_UserGuide_112015

1 Purpose

This getting started guide describes the setup of an Atmel®ATSAMB11 Xplained board and bringing up

an example profile supplied as part of the BluSDK SMART release. The Bluetooth®Find Me Profile is an

example application that is embedded as part of the software release package.

2 Demo Setup

3 Hardware Setup

Connect the ATSAMB11 board to the host PC using a Micro-USB cable.

Figure 3-1. EDBG USB Port

BLE Link

iPhone/Android

Atmel SmartConnect App

(Find Me Locator)

ATSAMB11

(Find Me Target)

ATSAMB11 BluSDK SMART –Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42612A-ATSAMB11-BluSDK-SMART-Find-Me-Profile-Getting-Started-Guide_UserGuide_112015

4 Find Me Target

The Find Me profile defines the behavior when a button is pressed on a device to cause an immediate

alert on a peer device. This can be used to allow users to find devices that have been misplaced.

Find Me Target Application which is the GATT server will hold the characteristics and wait for the Find Me

locaters alerts and based on the alerts level it will do the appropriate task.

Alert Level Characteristic

When the Find Me Locator device wishes to cause an alert on the Find Me Target device, it shall write the

specific Alert Level in the Alert Level characteristic.

ATSAMB11 BluSDK SMART –Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42612A-ATSAMB11-BluSDK-SMART-Find-Me-Profile-Getting-Started-Guide_UserGuide_112015

5 Software Setup

5.1 Installation Steps

1. Install the latest Atmel Studio [Atmel Studio 7.0 (build 629 or later) web installer

(recommended)]

http://www.atmel.com/tools/ATMELSTUDIO.aspx.

2. Install the latest Atmel Software Framework.

This package will install the following examples within the Atmel Studio environment:

Find Me application for ATSAMB11

5.2 Build Procedure

The following procedure is explained for ATSAMB11 application example.

1. Select New Example Project.

Figure 5-1. Creating a New Example Project

2. Select “SAMB11” in device family, enter “Find Me” in search window, and expand Atmel Corp

Projects. The location and the name of the project can be selected in the respective fields. Click

OK.

Figure 5-2. Selecting Find Me Application from Example Projects

3. Accept the license Agreement. The Atmel studio will generate the Find Me Target project for

ATSAMB11.

4. Build the solution.

ATSAMB11 BluSDK SMART –Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42612A-ATSAMB11-BluSDK-SMART-Find-Me-Profile-Getting-Started-Guide_UserGuide_112015

Figure 5-3. Building the Find Me Application

5. Download the application via the USB to the ATSAMB11 board by using the Device Programing

option available in Tools as shown below.

Figure 5-4. Programming the Find Me Application

6. Inside the device programming the user has to select the correct configuration for the device and

finally program the device by using the program button.

Figure 5-5. Flash the Find Me Application

7. Once the application is flashed, the Phone Alert Status Client Application is ready for usage.

ATSAMB11 BluSDK SMART –Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42612A-ATSAMB11-BluSDK-SMART-Find-Me-Profile-Getting-Started-Guide_UserGuide_112015

6 Console Logging

For the purpose of debugging, a logging interface had been implemented in the Find Me Application.

The logging interface utilizes the same EDBG port that connects to ATSAMB11. A serial port monitor

application (for example TeraTerm) shall be opened and attached to the corresponding COM port

enumerated on the PC by the device. The baud rate should be set to 115200.

ATSAMB11 BluSDK SMART –Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42612A-ATSAMB11-BluSDK-SMART-Find-Me-Profile-Getting-Started-Guide_UserGuide_112015

7 Running the Demo

1. Power on the ATSAMB11 by connecting the USB cable.

2. Open a console window using TeraTerm or any equivalent serial port monitor application and

connect to the corresponding COM port enumerated on the PC. Configure the COM Port with the

following settings: Baudrate 115200, Parity None, one Stop bit, one Start bit, no Hardware

Handshake.

3. Press the Reset button on the ATSAMB11 board.

4. The device is now in advertising mode.

Figure 7-1. Console Display for Device in Advertising Mode

Initializing Find Me Application

Initializing SAMB11

BD Address:0xF8F005F23FFF, Address Type:0

The Supported Services in Find Me Profile are:

-> Immediate Alert Service

Bluetooth device is in Advertising Mode

5. On the iPhone®, enable Bluetooth in the Settings page. Start the Atmel SmartConnect App and

scan for devices. ATMEL-FMP will be appear amongst the devices scanned. Click on ATMEL-FMP

to connect to the ATSAMB11 device.

Figure 7-2. ATMEL-FMP in Device Discovery Atmel SMART App

6. Once connected, the client side will request for the pairing procedure with the iPhone. The console

log provides a guidance for the user to enter the pass-key on iPhone.

ATSAMB11 BluSDK SMART –Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42612A-ATSAMB11-BluSDK-SMART-Find-Me-Profile-Getting-Started-Guide_UserGuide_112015

Figure 7-3. Console Display for Find Me Application Pairing

Initializing Find Me Application

Initializing SAMB11

BD Address:0xF8F005F23FFF, Address Type:0

The Supported Services in Find Me Profile are:

-> Immediate Alert Service

Bluetooth device is in Advertising Mode

Connected to peer device with address 0xccfa00710852

Connection Handle 0

Peer device request pairing

Sending pairing response

Please Enter the following Pass-code(on other Device):123456

Pairing procedure completed successfully

Find Me : Mild Alert

Find Me : High Alert

Find Me : No Alert

7. Once the device is connected, the following services shall be displayed on the App.

Figure 7-4. Services Discovered in ATMEL-FMP Device

8. Since the service level connection is now established, the user will see the notifications based on

the alert level settings as depicted in the following diagrams.

ATSAMB11 BluSDK SMART –Find Me Profile –Getting Started Guide [USER GUIDE]

Atmel-42612A-ATSAMB11-BluSDK-SMART-Find-Me-Profile-Getting-Started-Guide_UserGuide_112015

Figure 7-5. Sending Alerts to Find Me Target ATMEL-FMP

Note: A BLE compatible Android phone with the Atmel SmartConnect App can also be used to run the

demo as described above. The Android version of the SmartConnect app provides the same look

and feel as the iOS mobile app described above. Hence the same steps shall be used to run the

demo on a BLE compatible Android phone.

Otros manuales para ATSAMB11 BluSDK SMART

Tabla de contenidos

Otros manuales de Placa madre de Atmel

Atmel

Atmel AVR ATasicICE POD Manual de usuario

Atmel

Atmel QT5 Xplained Pro Manual de usuario

Atmel

Atmel SAM C21 Xplained Pro Manual de usuario

Atmel

Atmel ATA6661-EK Instrucciones de instalación y funcionamiento

Atmel

Atmel AT91EB42 Manual de usuario

Atmel

Atmel ATMEGA256RFR2-ZUR Manual de usuario

Atmel

Atmel AVR32 EVK1100 Manual de usuario

Atmel

Atmel AT90USB162 Manual de usuario

Atmel

Atmel Xmega A1U Xplained Pro Guía de inicio rápido

Atmel

Atmel AT89STK-11 Manual de instalación

Atmel

Atmel PROTO1 Xplained Pro Manual de usuario

Atmel

Atmel SAM L21 Xplained Pro Manual de usuario

Atmel

Atmel SAM4E-EK Manual de usuario

Atmel

Atmel AT90USB162 Manual de usuario

Atmel

Atmel AT91EB55 Manual de usuario

Atmel

Atmel ATA8520-EK3-E Manual de usuario

Atmel

Atmel OLED1 Xplained Pro Manual de usuario

Atmel

Atmel ATA6612-EK Instrucciones de instalación y funcionamiento

Atmel

Atmel AT91SAM9263-EK Manual de usuario

Atmel

Atmel REB231ED Manual de usuario

Atmel

Atmel AT91SAM7A2-EK Manual de usuario

Atmel

Atmel AT91RM3400 Manual de usuario

Atmel

Atmel AT88CK9000 Manual de usuario

Atmel

Atmel SAM9N12/CN11-EK Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario