Atmel AVR128 Instrucciones de instalación y funcionamiento

AVR 8-bit Microcontrollers

AVR128: Setup and Use of the AVR Analog

Comparator

APPLICATION NOTE

Introduction

This application note serves as an example on how to set up and use the

Atmel® AVR® On-chip Analog Comparator. The following program examples

are given in the assembly file “avr200.asm”:

•Detect a positive edge on the comparator output by polling the ACO-

bit in the Analog Comparator Control and Status Register – ACSR.

•Detect a positive edge on the comparator output by polling the Analog

Comparator Interrupt Flag – ACI in ACSR.

•Initialize interrupt on comparator output toggle. An interrupt routine

which increments a 16-bit counter each time it is executed is given as

an example.

Atmel-0934C-Setup-and-Use-of-the-AVR-Analog-Comparator_AVR128_Application Note-07/2016

Table of Contents

Introduction......................................................................................................................1

1. Detecting a Positive Edge By Polling ACO................................................................3

2. Detecting a Positive Edge by Polling ACI.................................................................. 4

3. Using the Analog Comparator Interrupt..................................................................... 6

4. Revision History.........................................................................................................7

Atmel AVR128: Setup and Use of the AVR Analog Comparator [APPLICATION NOTE]

Atmel-0934C-Setup-and-Use-of-the-AVR-Analog-Comparator_AVR128_Application Note-07/2016

1. Detecting a Positive Edge By Polling ACO

This part of the code shows the trivial way of detecting a positive edge on the comparator output. Even

though it uses only four words of code and no initial setup, this approach to the task might cause

problems. If a short pulse on the output occurs while the program is administrating the wait loop, the

pulse could be missed as ACO is directly connected to the comparator output. If the user wants to insert

code within the wait loop, the probability of detecting a short pulse will increase. Such code might be time-

out if no edge occurs within a specific period. The procedure for detection is as follows:

1. If output is high, wait for output to go low.

2. Wait until output goes high.

Figure 1-1. ACO Polling Flow Chart

S TART

DONE

ACO = 0?

ACO = 1?

Table 1-1. ACO Polling Performance Figures

Parameter Value

Code Size (Words) 4

Response Time (Cycles) 3 - 5

Initialization Time (Cycles) 0

High Registers: None

Pointers: None

Interrupts Usage None

Peripherals Usage Analog Comparator

Atmel AVR128: Setup and Use of the AVR Analog Comparator [APPLICATION NOTE]

Atmel-0934C-Setup-and-Use-of-the-AVR-Analog-Comparator_AVR128_Application Note-07/2016

2. Detecting a Positive Edge by Polling ACI

This part of the code shows a far more secure and flexible way of detecting a positive edge on the

comparator output. Even though the Analog Comparator Interrupt is disabled, the interrupt flag will still be

set when events on the comparator output matches the settings of the ACIS1/ACIS0 bits in ACSR. E.g., a

positive edge will always set the ACI bit in ACSR if ACIS1/ACIS0 both are one (refer to the datasheet for

details). The ACI flag will reflect whether the event to look for has occurred since the last ACI Reset. In

this application note, positive edge detection by polling ACI is implemented according to the following

procedure:

Setup

1. Set ACIS0 and ACIS1 = 1.

Polling

1. Clear the ACI bit by writing a logical "1" to it.

2. Wait until ACI goes high.

Figure 2-1. ACI Polling Flow Chart

S ETUP

DONE

ACO = 1?

ACIS 1/ACIS 0 ← 11

CLEAR ACI

Table 2-1. ACI Polling Performance Figures

Parameter Value

Code Size (Words) 5

Initialization Time (Cycles) 2

Response Time (Cycles) 3 - 5

High Registers: None

Pointers: None

Atmel AVR128: Setup and Use of the AVR Analog Comparator [APPLICATION NOTE]

Atmel-0934C-Setup-and-Use-of-the-AVR-Analog-Comparator_AVR128_Application Note-07/2016

Parameter Value

Interrupts Usage None

Peripherals Usage Analog Comparator

Atmel AVR128: Setup and Use of the AVR Analog Comparator [APPLICATION NOTE]

Atmel-0934C-Setup-and-Use-of-the-AVR-Analog-Comparator_AVR128_Application Note-07/2016

3. Using the Analog Comparator Interrupt

The application note program shows an example on how to enable the comparator interrupt. In the

example, interrupt on comparator toggle is shown. The following procedure is followed:

1. Clear interrupt flag and ACIS1/ACIS0. The interrupt flag must be cleared first. If not, and the flag for

some reason already is set, the MCU will start executing the interrupt routine immediately when the

interrupts is enabled. Clearing ACIS1/ACIS0 selects interrupt on toggle.

2. Enable Global Interrupts.

3. Enable the Analog Comparator Interrupt by setting the ACIE bit in ACSR.

Note that since the ACSR Register is one of the lower 32 I/O, registers, the “SBI” instruction can be used

to set, clear and test bits.

Table 3-1. Analog Comparator Interrupt Enable Performance Figures

Parameter Value

Code Size (Words) 4

Execution Time (Cycles) 5

High Registers: 1

Pointers: None

Interrupts Usage None

Peripherals Usage Analog Comparator

Atmel AVR128: Setup and Use of the AVR Analog Comparator [APPLICATION NOTE]

Atmel-0934C-Setup-and-Use-of-the-AVR-Analog-Comparator_AVR128_Application Note-07/2016

4. Revision History

Doc. Rev. Date Comments

0934C 07/2016 New template

0934B 05/2002

0934A Initial document release.

Atmel AVR128: Setup and Use of the AVR Analog Comparator [APPLICATION NOTE]

Atmel-0934C-Setup-and-Use-of-the-AVR-Analog-Comparator_AVR128_Application Note-07/2016

Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com

Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, AVR® and others are registered trademarks or trademarks of Atmel Corporation in

U.S. and other countries. Other terms and product names may be trademarks of others.

DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any

intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND

CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED

OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY,

FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,

CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS

INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this

document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to

update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive

applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any

applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without

an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the

operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments

unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically

designated by Atmel as automotive-grade.

Tabla de contenidos

Otros manuales de Microcontrolador de Atmel

Atmel

Atmel ATmega128A-STK600 Instrucciones de instalación y funcionamiento

Atmel

Atmel AVR ATtiny15L Manual del propietario

Atmel

Atmel AVR1925 XMEGA-C3 Xplained Manual de usuario

Atmel

Atmel AVR1921 Instrucciones de instalación y funcionamiento

Atmel

Atmel AT43DK380 Manual de usuario

Atmel

Atmel AT90PWM2 Manual de usuario

Atmel

Atmel ATmega324PB Manual de usuario

Atmel

Atmel AT89STK-03 Manual de instalación

Atmel

Atmel develer DevelBoard Blue Guía rápida de usuario

Atmel

Atmel AVR ATtiny10 Series Manual de usuario

Atmel

Atmel AVR1909 Manual de instalación

Atmel

Atmel SAM4SD32B Manual de instrucciones

Atmel

Atmel AT91 Series Manual de usuario

Atmel

Atmel AVR1019 Instrucciones de instalación y funcionamiento

Atmel

Atmel AT43DK325 Manual de usuario

Atmel

Atmel UC3-L0 Xplained Instrucciones de instalación y funcionamiento

Atmel

Atmel AT90USB162 Manual de usuario

Atmel

Atmel SAM D09 Instrucciones de instalación y funcionamiento

Atmel

Atmel megaAVR Manual de usuario

Atmel

Atmel AVR32918 Manual de usuario

Atmel

Atmel QTouch Instrucciones de instalación y funcionamiento

Atmel

Atmel ATtiny104 Xplained Nano Manual de usuario

Atmel

Atmel AVR AT90CAN32 Manual de usuario

Atmel

Atmel ATmega48PV Manual de usuario

Manuales populares de Microcontrolador de otras marcas

AMS

AMS AS7261 Demo Kit Manual de usuario

Novatek

Novatek NT6861 Manual de usuario

Espressif Systems

Espressif Systems ESP8266 SDK Guía de configuración

Nuvoton

Nuvoton ISD61S00 ChipCorder Guía

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manual de usuario

Texas Instruments

Texas Instruments Chipcon CC2420DK Manual de usuario

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manual de usuario

NEC

NEC 78GK0S/K 1+ Series Instrucciones de instalación y funcionamiento

Mikroe

Mikroe SEMITECH N-PLC Click Instrucciones de instalación y funcionamiento

Intel

Intel Agilex Manual de usuario

Cypress

Cypress CY4607 HX2VL Manual de usuario

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manual de usuario

Texas Instruments

Texas Instruments TMS320F2837 D Series Manual de usuario

CYPRES

CYPRES CY14NVSRAMKIT-001 Manual de usuario

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manual de usuario

Espressif Systems

Espressif Systems ESP8266EX Instrucciones de funcionamiento

Abov

Abov AC33M8128L Manual de usuario

Laird

Laird BL654PA Manual de usuario