Atlona AT-UHD-CAT-4 Manual de usuario

atlona.com Toll free: 1-877-536-3976

Local: 1-408-962-0515

CAT-4 Package Contents CAT-8 Package Contents

AT-UHD-CAT-4 / AT-UHD-CAT-8 Installation Guide

Please check http://www.atlona.com/product/AT-UHD-CAT-4

and http://www.atlona.com/product/AT-UHD-CAT-8 for the

most recent firmware update or manual.

4K/UHD 4/8-Output HDMI to HDBaseT

Distribution Amplifiers

The Atlona AT-UHD-CAT-4 is a 4K/UHD HDMI to HDBaseT™ distribution amplifier featuring pass-

through HDMI input connections, four HDBaseT outputs and display control capability. The Atlona

AT-UHD-CAT-8 has the same capabilities, but adds an additional four HDBaseT outputs and RS-

232/IR connectors. Each output transmits AV and control signals up to 230 ft. (70 m) @ 1080p

and 130 ft. (40 m) @ 4K/UHD. Features include 4K/UHD @ 60 Hz with 4:2:0 chroma subsampling,

HDCP 2.2 compliance, EDID management, and PoE for remote receiver powering. A wide variety of

consumer and commercial displays may be controlled by the AT-UHD-CAT-4 / AT-UHD-CAT-8 using

CEC. Designed for commercial or residential distribution applications, both the AT-UHD-CAT-4 /

AT-UHD-CAT-8 are control system-friendly and integrate with any TCP/IP, RS-232, or IR control

system. Both units feature a 1U, full-rack width enclosure with external, international power

supply.

• 1 x AT-UHD-CAT-4

• 5 x Female captive screw connectors

5 pin: RS-232 and IR

• 1 x Short rack ear

• 1 x Long rack ear

• 2 x Mounting plates

• 1 x Rubber feet

• 1 x 48V/3.125A DC power supply adaptor

• 1 x Installation Guide

• 1 x AT-UHD-CAT-8

• 9 x Female captive screw connectors

5 pin: RS-232 and IR

• 1 x Pair rack ears

• 1 x Rubber feet

• 1 x 48V/3.125A DC power supply adaptor

• 1 x Installation Guide

atlona.com Toll free: 1-877-536-3976

Local: 1-408-962-0515

DC 48V

HDMI

MASTER

LAN

41 2 3

EDID

LEARN

INT

POWER

AT-UHD-CAT-4

HDMI

OUT

HDBaseT LOCK

RS-232 RS-232 RS-232 RS-232IR

123 4

1OUTIN 23 4

RX RXTX RX TX RX TX RX TXTX

HDBaseT OUT

RXTX

RS-232 IR

RX RXTX TX

DC 48V

HDMI

MASTER

LAN

41 2 3

EDID

LEARN

INT

POWER

AT-UHD-CAT-4

HDMI

OUT

HDBaseT LOCK

RS-232 RS-232 RS-232 RS-232IR

123 4

1OUTIN 23 4

RX RXTX RX TX RX TX RX TXTX

HDBaseT OUT

RXTX

RS-232 IR

RX RXTX TX

CAT-4 Panel Description

Front Panel

1. HDMI LED - Illuminates when receiving/transmitting signals

2. HDBaseT LEDs - Illuminates when connected to a compatible PoE receiver

3. LOCK LED - Illuminates when buttons are locked

4. Power button - Switch the unit or a display on/off.

Note: Function is dependent upon what is selected via RS-232 or webGUI. Default is unit on/off.

5. EDID

LEDs - Lights up to indicate what EDID mode the unit is in

Button - Switches between internal and learned EDID modes

Back Panel

1. LAN port - Connect to network router for control

2. Master control - Connect to PC or control system for unit control

3. RS-232 / IR control ports - Connect to PC or control system for zone control

4. FW port - Connect to a PC for firmware updating

5. HDMI ports - Connect HDMI source and display to these ports

6. HDBaseT OUT ports - Connect HDBaseT PoE receivers to this port (e.g. AT-UHD-EX-70C-RX, etc)

Note: Compatible PoE receivers do not need power

7. DC 48V port - Connect included 48V power supply to this port

5 6 7

atlona.com Toll free: 1-877-536-3976

Local: 1-408-962-0515

MASTER

RS-232 IR

RX RXTX TX

RS-232 IR

RX RX

TX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RX

TX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RXTX TX

DC 48V IN

IN OUT

HDMILAN

HDBaseT OUT

2 3 5 86 7

41 2 3IN OUT

EDID

LEARNINT

POWER

AT-UHD-CAT-8

HDMI OUTPUT

85 6 7

LOCK

MASTER

RS-232 IR

RX RXTX TX

RS-232 IR

RX RX

TX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RX

TX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RXTX TX

DC 48V IN

IN OUT

HDMILAN

HDBaseT OUT

2 3 586 7

41 2 3IN OUT

EDID

LEARNINT

POWER

AT-UHD-CAT-8

HDMI OUTPUT

85 6 7

LOCK

CAT-8 Panel Description

Front Panel

1. HDMI LED - Illuminates when receiving/transmitting signals

2. HDBaseT LEDs - Illuminates when connected to a compatible PoE receiver

3. LOCK LED - Illuminates when buttons are locked

4. Power button - Switch the unit or a display on/off.

Note: Function is dependent upon what is selected via RS-232 or webGUI. Default is unit on/off.

5. EDID

LEDs - Lights up to indicate what EDID mode the unit is in

Button - Switches between internal and learned EDID modes

Back Panel

1. Master control - Connect to PC or control system for unit control

2. RS-232 / IR control ports - Connect to PC or control system for zone control

3. FW port - Connect to a PC for firmware updating

4. LAN port - Connect to network router for control

5. HDMI ports - Connect HDMI source and display to these ports

6. HDBaseT OUT ports - Connect HDBaseT PoE receivers to this port (e.g. AT-UHD-EX-70C-RX, etc)

Note: Compatible PoE receivers do not need power

7. DC 48V port - Connect included 48V power supply to this port

5 6 7

atlona.com Toll free: 1-877-536-3976

Local: 1-408-962-0515

Mounting (CAT-4 only)

Mounting (CAT-8 only)

Rack Ear x 1

Mounting Plate x 2

The UHD-CAT-4 can be mounted in three ways: as a single unit in a rack, with a second unit in a

rack, or against a wall/table using the mounting plates.

Single unit mounting will use the long rack ear and short rack ear to affix the unit to the rack.

Two unit mounting will use two short rack ears (the second will be in the box with the second unit) and two

mountings plates to affix the two units together inside the rack.

Wall/table mounting will use both mounting plates to affix the unit to a table or wall.

Oval holes on

the rack ears will

always be attached

to the rack.

Circular holes

will always be

attached to

the unit.

Larger oval

hole will be

attached to

the wall/table.

RS-232

Connection

RS-232 is often connected through a DB 9-pin to captive screw

connector. The pins will have functions associated with them,

some will be unassigned.

Note: Typical DB9 connectors use pin 2 for TX, pin 3 for RX, and pin

5 for ground. On some devices functions of pins 2 and 3 are

reversed.

54 3 2

9 8 7 6

RS-232 pin out will be determined by the RS-

232 cable and will connect as Rx (receiver), Tx

(transmitter), and (ground). (See picture 1)

Wire color will

differ by cable

manufacturer.

RS-232

RX TX

Rack Ear x 2

Circular holes

will always be

attached to

the unit.

atlona.com Toll free: 1-877-536-3976

Local: 1-408-962-0515

Set Up

To set up the RS-232 hyperterminal (if not using 3rd party software) use the following steps:

1. Connect the UHD-CAT-4 / UHD-CAT-8 to a PC using a 3 pin to USB cable

2. Go to the Device Manager folder (see picture A)

3. Find the UHD-CAT-4 / UHD-CAT-8 COM port and right click with a mouse and select properties

(see picture B)

Note: If unsure which COM port is used by the UHD-CAT-4 / UHD-CAT-8, unplug the cable and plug it back

in. It will disappear and reappear on the COM port list.

4. Under the properties menu select the port settings tab and update the menu to the default

settings of: Bits Per Second: 115200, Data Bits: 8, Parity: None, Stop Bits: 1 and Flow

Control: None. (see picture C)

Set up is done and any hyperterminal program may be used to control the UHD-CAT-4 or UHD-CAT-8.

ABC

System IR is typically used to connect to control system processors. This input is used to control the

UHD-CAT-4 and UHD-CAT-8.

Note: The IR receiver is optional for the UHD-CAT-4 / UHD-CAT-8. The compatible IR receiver (AT-IR-CS-RX) can be

purchased through atlona.com.

The wires of the emitter (TX) and receiver (RX) have been marked to differentiate the pin outs.

The included IR emitter has two wires: TX and ground. Signal (TX) will have a solid line and ground

will be blank.

Signal (TX)

Ground ( )

atlona.com Toll free: 1-877-536-3976

Local: 1-408-962-0515

A login screen will appear (this is the same log in for admin and general users). For the first log in (and future

admin changes) the username is “root” and password is “Atlona”.

Note: Only the admin password can be changed. The username will always remain “root”.

TCP/IP

TCP/IP webGUI

Atlona has created an easy to use webGUI for initial setup and later changes to the configuration

of the UHD-CAT-4 / UHD-CAT-8.

To begin, connect the LAN port of the UHD-CAT-4 / UHD-CAT-8 to your network. Type the IP

address of the UHD-CAT-4 / UHD-CAT-8 into the web browser of a PC connected to the same

network (as seen below).

To find the switcher IP: Use the RS-232 command “IPCFG”.

Important: If any stability issues are experienced, disable any anti-virus or firewall that may interfere with

network communication to the switcher. Once set up is done and the switcher GUI is no

longer being used, the firewall and anti-virus can be re-enabled.

For convenience, the UHD-CAT-4 / UHD-CAT-8 comes with DHCP on. This enables the UHD-CAT to

be connected to a network without the concern of conflicting IP addresses. If your network does

not support DHCP, this feature may be turned off and the IP address set using

RS-232 commands or the webGUI.

Note: Press and hold the Power button on the front panel to switch between static and DHCP IP address. Two button

flashes means the unit is in static mode and four button flashes means the unit is DHCP. Static IP configuration

will be: 192.168.1.254 - 255.255.255.0.

Note: If your system is controlled using IP, it is strongly recommended that you disable DHCP and select an unused IP

address so that your system controller doesn’t lose contact with the switcher.

atlona.com Toll free: 1-877-536-3976

Local: 1-408-962-0515

MASTER

RS-232 IR

RX RXTX TX

RS-232 IR

RX RX

TX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RX

TX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RXTX TX

RS-232 IR

RX RXTX TX

DC 48V IN

IN OUT

HDMILAN

HDBaseT OUT

2 3 586 7

41 2 3IN OUT

EDID

LEARNINT

POWER

AT-UHD-CAT-8

HDMI OUTPUT

85 6 7

LOCK

Control Drivers

CAT-4 / CAT-8 Updating

Visit the Control Drivers tab at http://www.atlona.com/product/AT-UHD-CAT-4/ or http://www.

atlona.com/product/AT-UHD-CAT-8 to download the control drivers.

Visit the Firmware Update tab at http://www.atlona.com/product/AT-UHD-CAT-4/ or http://www.

atlona.com/product/AT-UHD-CAT-8 to download the current updates and instructions.

Note: Atlona is constantly improving and updating features and stability. It is recommended that you check to make

sure you are on the most current firmware before installation, especially when using a control system.

Connection Diagram (UHD-CAT-8)

FW LINK

POWER

AT-UHD-EX-100CE-RX

RS-232

RXTX

IR IN

IR OUT

HDBaseT IN

ETHERNET

HDMI OUT

FW LINK

POWER

AT-UHD-EX-100CE-RX

RS-232

RXTX

IR IN

IR OUT

HDBaseT IN

ETHERNET

HDMI OUT

FW LINK

POWER

AT-UHD-EX-100CE-RX

RS-232

RXTX

IR IN

IR OUT

HDBaseT IN

ETHERNET

HDMI OUT

FW LINK

POWER

AT-UHD-EX-100CE-RX

RS-232

RXTX

IR IN

IR OUT

HDBaseT IN

ETHERNET

HDMI OUT

COM

GND

SIG

+12V

GND

SIG

+12V

GND

SIG

+12V

GND

SIG

+12V

1 2 3 4

RELAYS

WIFI 2

ZIGBEE 12V DC

IR OUT

IDFACTORY

RESTORE

SERIAL1

SERIAL2

HDMI COMPONENT

VIDEO OUT ETHERNET CONTACTS

AUDIO OUT

AUDIO IN

WIFI 1 eSATADIGITAL

COAX OUT

AT-UHD-CAT-8

Control System

Blu-ray Player

Display 1

Display 2

Display 3

Display 4

AT-UHD-EX-100CE-RX

AT-UHD-EX-100CE-RX Video

Control

Video

Control

Video

Control

HDBaseT

Video

Control

Video

HDBaseT

Control

atlona.com Toll free: 1-877-536-3976

Local: 1-408-962-0515

Troubleshooting

1. What is the default static IP address of this unit?

192.168.1.254. By default, this unit comes with DHCP enabled. To use the default static IP

address, press the Power button for 15 seconds. The default subnet mask is 255.255.255.0

and the default gateway address is 192.168.1.1.

2. How do I determine the current IP address of the unit?

Connect to the RS-232 port and send the IPCFG command.

3. What does the EDID button, on the front panel, do?

You can use the EDID button to switch between internal and learned EDID modes.

Refer to the User Manual for more information.

4. How do I check the firmware version of this unit?

You can check the firmware through AMS or the webGUI, or by sending the following

command via TCP/IP or RS-232: Version mcu.

5. How do I update the firmware?

Firmware and instructions can be found and downloaded from the firmware tab at

http://www.atlona.com/product/AT-UHD-CAT-4ED/

6. The buttons on the front panel aren’t working. What’s wrong?

Make sure that the Lock feature is disabled. This can be done within AMS or the webGUI,

or by sending the Unlock command, using TCP/IP or RS-232.

Otros manuales para AT-UHD-CAT-4

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Amplificador de Atlona

Atlona

Atlona AT-HD-V14 Manual de usuario

Atlona

Atlona AT-SAV18 Manual de usuario

Atlona

Atlona AT-3GSDI-14 Manual de usuario

Atlona

Atlona AT-HD19SS Manual de usuario

Atlona

Atlona AT-VGA11S Manual de usuario

Atlona

Atlona AT-GAIN-60 Manual de usuario

Atlona

Atlona AT-VGA14A Manual de usuario

Atlona

Atlona AT-VID18-BNC Manual de usuario

Atlona

Atlona AT-VID18-BNC Manual de usuario

Atlona

Atlona AT-PA100 Manual de usuario

Atlona

Atlona AT-SDI-14 Manual de usuario

Atlona

Atlona Gain 120 Manual de usuario

Atlona

Atlona AT-VID18 Manual de usuario

Atlona

Atlona AT-AV14 Manual de usuario

Atlona

Atlona AT-AV14 Manual de usuario

Atlona

Atlona AT-PA100-G2 Manual de usuario

Atlona

Atlona AT-VID18-BNC Manual de usuario

Atlona

Atlona AT-HD-V116 Manual de usuario

Atlona

Atlona AT-VGA12A Manual de usuario

Atlona

Atlona AT-VGA18 Manual de usuario

Atlona

Atlona AT-HD-V116 Manual de usuario

Atlona

Atlona AT-HDDA-2 Manual de usuario

Atlona

Atlona AT-HD-V112 Manual de usuario

Atlona

Atlona AT-SAV14 Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario