Atlas Copco RRC13 Series Hoja de instrucciones
RRC13
Printed Matter No. 9836 9785 00 Chipping Hammer
2010-08-01 Product Instructions
RRC13 8425 0101 30
RRC13B 8425 0101 33
RRC13N 8425 0101 36
WARNING
Read all safety warnings and instructions
Failure to follow the safety warnings and in-
structions may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future
reference
2© Atlas Copco Industrial Technique AB - 9836978500
Table of Contents
EN Product Instructions.......................................................................... 3
FR Instructions sur le produit .............................................................. 14
DE Produktanweisungen...................................................................... 26
ES Instrucciones del producto ............................................................ 38
PT Instruções do produto .................................................................... 50
IT Istruzioni sul prodotto..................................................................... 62
NL Productinstructies ........................................................................... 74
DA Produktanvisninger......................................................................... 86
NO Produktanvisninger......................................................................... 97
FI Tuoteohjeet.................................................................................... 108
SV Produktanvisningar....................................................................... 119
RU Инструкции по изделию ............................................................ 130
PL Instrukcje produktu ....................................................................... 142
HU Termékutasítások ......................................................................... 154
RRC13 EN Safety and operating instructions
© Atlas Copco Industrial Technique AB - 9836 978500 00 3
Safety and operating instructions
Safety instructions
Important information for safer use of percussive tools
This manual follows the EC Machines Directive (2006/42/EC) regarding opera-
tor's instructions and relevant parts of standards from CEN TC 255 "Hand-held
power driven non-electric tools - Safety" These instructions concern operation,
handling of machine, inserted tool and equipments as well as maintenance.
Neglect to follow these long established recommendations may cause serious
hazards.
Make sure that the operator has fully understood the following recommenda-
tions and has full access to them.
pay strict attention to following measures the operator has to take in order to
avoid risks of misuse or accident
Installation
Follow the instructions for air preparation given in the written instructions sup-
plied with the machine.
When lubrication is recommended - use recommended lubricants only.
Check hose size and air pressure.
Avoid the risk of whipping hose - regularly check hose, hose fittings and condi-
tion of clamps.
Check that the exhaust air is directed to avoid blowing dust or air from the work
piece onto the operator or other persons. Arrange for barriers if possible.
When necessary, use exhaust hose and arrange for dust collection.
Avoid accidents when using the machine
1 The chisel, die or punch may fall out or may be shot out of the
tool accidentally causing serious injury
To prevent injury from a flying chisel:
• always use a retainer
• inspect the retainer for wear or damage regularly
Safety and operating instructions EN RRC13
4© Atlas Copco Industrial Technique AB - 9836 978500 00
and:
• be aware that the chisel may break during operation due to fatigue
• never trigger the machine unless held against a work piece
• remove chisel, die or punch from machine when work is over
• before changing accessories, chisel or die - disconnect the machine from the
air supply
• release the start and stop device in case of interruption of energy supply
• when finishing a job, disconnect the machine from its air supply
2 Chips and sparks shall be prevented from striking an eye or
another worker
To prevent vision loss:
• always wear eye protection
• isolate work of this kind by using barriers between work stations
• do not use the machine for other purposes than it is intended for
3 Prevent body injury by using:
• gloves
• protective shoes
• helmet
• always wear eye protection
4 Explosive atmosphere must not be ignited
To prevent injury and property loss from fires:
• use other technique
• use accessories of non sparking material (e.g. needle attachment of Beryl-
lium copper for a needle scaler)
5 Electric chock may be fatal
• avoid chiselling into electric wiring hidden inside walls etc.
RRC13 EN Safety and operating instructions
© Atlas Copco Industrial Technique AB - 9836 978500 00 5
Long term risks when using the machine
6 Always use ear protection
To prevent gradual loss of hearing due to exposure to high noise levels:
• wear ear protection
7 Vibration may be harmful to hands and arms
• use vibration dampened tools if available
• reduce the total time of exposure to vibrations, particularly if the operator
has to guide the chisel by hand
8 Dust generated during operation may be harmful
• use spot suction or a breathing apparatus
Proper use and maintenance
9 Do not perform idle blows with a hammer
• they will cause high internal stresses and shorten the life of the tool
• note the risk of shooting out the chisel, die or punch if the retainer is not in
order
10 Quick coupling
• if a quick coupling is used on a percussive tool, it shall be separated from
the tool by a whip hose (length 0.5 m)
11 Maintenance
Good service life and safe function is offered if the instructions for lubrication,
maintenance and overhaul supplied with the machine are followed.
Use genuine Atlas Copco replacement kits and parts only.
Safety and operating instructions EN RRC13
6© Atlas Copco Industrial Technique AB - 9836 978500 00
Warning
Make sure you are familiar with the operating instructions before you use this
machine.
This machine, its attachments and accessories must only be used for the pur-
pose for which they were designed:
• General chipping and scaling work, fettling of castings in foundries, hole
making and light demolition in construction and building industry (not for
nailing without proper attachments).
RRC 13N – for removing welding slag, rust and paint from steel structures.
For product liability and safety reasons any modification to the machine, its at-
tachments or accessories must be agreed in advance with an authorized techni-
cal representative of the manufacturer.
RRC 13B
• When operating the tool to blow the workpiece clean – direct tool exhaust
from operator and co-workers.
General information
EC DECLARATION OF CONFORMITY
We, Atlas Copco Industrial Technique AB, S-105 23 STOCKHOLM, SWE-
DEN declare that the product (with name, type and serial number, see front
page) is in conformity with the following Directive(s):
2006/42/EC
Harmonised standards applied:
ISO 11148-4
Technical file available from:
Quality Manager, Atlas Copco Industrial Technique, Stockholm, Sweden
Stockholm, 1 July 2013
Tobias Hahn, Managing Director
Signature of issuer
Installation
Installation
RRC 13
• Install chisel (h), see figure.
RRC13 EN Safety and operating instructions
© Atlas Copco Industrial Technique AB - 9836 978500 00 7
RRC 13B
• Install chisel (h), see figure.
RRC 13N
• Install needle set (j; 68), see figure.
Always use complete sets of needles of the same length to ensure the full
working capacity of the machine is reached.
Air quality
• For optimum performance and maximum machine life we recommend the
use of compressed air with a maximum dew point of +10°C. We also rec-
ommend the installation of an Atlas Copco refrigeration-type air dryer.
• Use a separate air filter of type Atlas Copco FIL. This filter removes solid
particles larger than 15 microns and also removes more than 90 % of liquid
water. The filter must be installed as close as possible to the machine/equip-
ment and prior to any other air preparation unit such as REG or DIM (please
see Air Line Accessories in our main catalogue). Blow out the hose before
connecting.
Models which need air lubrication:
• The compressed air must contain a small quantity of oil.
We strongly recommend that you install an Atlas Copco oil-fog lubricator
(DIM). This should be set according to air consumption by the air line tool
according to the following formula:
Safety and operating instructions EN RRC13
8© Atlas Copco Industrial Technique AB - 9836 978500 00
L = Air consumption (litre/s).
(May be found in our sales literature).
D = Number of drops per min (1 drop = 15 mm3)
L* 0.2 = D
this applies to the use of long work cycle air line tools. A single point lubri-
cator type Atlas Copco Dosol can also be used for tools with short running
cycles.
Information about Dosol settings may be found under Air Line Accessories
in our main catalogue.
Lubrication-free models:
• In the case of lubrication-free tools it is up to the customer to decide on the
peripheral equipment to be used. However, it is no disadvantage if the com-
pressed air contains a small quantity of oil e.g. supplied from a fog lubrica-
tor (DIM) or Dosol system. This does not apply to turbine tools, which
should be kept oil free.
Compressed air connection
• The machine is designed for a working pressure of 6–7 bar = 600–700 kPa =
87–102 psi.
• Blow out the hose before connecting.
Installation proposal
Choosing the correct couplings, hose and clamps can be a troublesome digging
into details. To save your time and to ensure correct capacity of the airline in-
stallation, from the tapping point to the tool, we offer you an installation pro-
posal.
For more information please read, Atlas Copco Industrial Power Tools cata-
logue Ordering No. 9837 3000 01.
RRC13 EN Safety and operating instructions
© Atlas Copco Industrial Technique AB - 9836 978500 00 9
Maintenance
Lubrication
The tool should be lubricated with about 10 drops of oil once per shift. The oil
can be dropped either into the air hose or straight through the adapter (16).
When the tool is in continuous service, installation of an Atlas Copco oil-fog lu-
bricator in the compressed air line is recommended.
Use lubricants of good quality. The oils listed in the lubrication table are exam-
ples of lubricants that can be recommended.
Grease guide
Brand Grease Air lubrication
BP Energrease LS-EP2 Energol E46
Esso Beacon EP2 Arox EP46
Q8 Rembrandt EP2 Chopin 46
Mobil Mobilegrease XHP 222 Almo Oil 525
Shell Alvania EP2 Torcula 32
Texaco Multifak EP2 Aries 32
Molycote BR2 Plus
Overhaul
If the tool is used every day, it should be overhauled and cleaned once every six
months.
The filter in the adapter (16) should be cleaned frequently to prevent choking
with resultant decrease in capacity.
Useful information
Log in to Atlas Copco www.atlascopco.com
You can find information concerning our products, accessories, spare parts and
published matters on our website.
Ergonomic guidelines
Consider your workstation as you read through this list of general ergonomic
guidelines and see if you can identify areas for improvement in posture, compo-
nent placement, or work environment.
• Take frequent breaks and change work positions frequently.
• Adapt the workstation area to your needs and the work task.
• Adjust for convenient reach range by determining where parts or tools
should be located to avoid static load.
• Use workstation equipment such as tables and chairs appropriate for the
work task.
• Avoid work positions above shoulder level or with static holding during as-
sembly operations.
Safety and operating instructions EN RRC13
10 © Atlas Copco Industrial Technique AB - 9836 978500 00
• When working above shoulder level, reduce the load on the static mus-
cles by reducing the weight of the tool, using for example torque arms,
hose reels or weight balancers. You can also reduce the load on the static
muscles by holding the tool close to the body.
• Make sure to take frequent breaks.
• Avoid extreme arm or wrist postures, particularly for operations requir-
ing a degree of force.
• Adjust for convenient field of vision by minimizing movement of the eyes
and head during the work task.
• Use the appropriate lighting for the work task.
• Select the appropriate tool for the work task.
• Use ear protection equipment in noisy environments.
• Use high-quality inserted tools or consumables to minimize exposure to ex-
cessive levels of vibration.
• Minimize exposure to reaction forces.
• When cutting:
A cut-off wheel can get stuck if the wheel is either bent or if it is not
guided properly. Make sure to use the correct flanges for cut-off wheels
and avoid bending the wheel during cut-off operation.
• When drilling:
The drill might stall when the drill bit breaks through. Makes sure you
use support handles if the stall torque is too high. The safety standard
ISO11148 part 3 recommends using something to absorb the reaction
torque above 10 Nm for pistol grip tools and 4 Nm for straight tools.
• When using direct-driven screw or nutrunners:
Reaction forces depend on tool setting and joint characteristics. The abil-
ity to bear reaction forces depends on the operator’s strength and pos-
ture. Adapt the torque setting to the operator's strength and posture and
use a torque arm or reaction bar if the torque is too high.
• Use dust extraction system or mouth protection mask in dusty environments.
Country of origin
Please refer to the information on the product label.
Spare parts
Parts without ordering number are not delivered separately for technical rea-
sons.
The use of other than genuine Atlas Copco replacement parts may result in de-
creased tool performance and increased maintenance and may, at the company
option, invalidate all warranties.
Warranty
Contact the Atlas Copco sales representative within your area to claim a prod-
uct. Warranty will only be approved if the product has been installed, operated
and overhauled according to the Operating Instructions.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Idiomas:
Otros manuales de Herramientas de Atlas Copco
Atlas Copco
Atlas Copco PRO P2536-R Hoja de instrucciones
Atlas Copco
Atlas Copco P2535-H Manual de usuario
Atlas Copco
Atlas Copco RRF 21-01 Hoja de instrucciones
Atlas Copco
Atlas Copco LPD Series Guía de mantenimiento y servicio
Atlas Copco
Atlas Copco ETVSL21-12-i06 Manual de usuario
Atlas Copco
Atlas Copco ETDES21-04-I06-PS Manual de usuario
Atlas Copco
Atlas Copco 8425 0206 15 Manual de usuario
Atlas Copco
Atlas Copco QST34-8CT-T50-L150-H6 Hoja de instrucciones
Atlas Copco
Atlas Copco P2539-H Instrucciones originales
Atlas Copco
Atlas Copco P2531-H Hoja de instrucciones
Atlas Copco
Atlas Copco SMC-TT-10-850 Manual de usuario
Atlas Copco
Atlas Copco TAM 14 Guía de mantenimiento y servicio
Atlas Copco
Atlas Copco EP5PTX15SR10-AT Instrucciones originales
Atlas Copco
Atlas Copco 4220 4522 82 Hoja de instrucciones
Atlas Copco
Atlas Copco BV30 Guía de mantenimiento y servicio
Atlas Copco
Atlas Copco RRD37 Hoja de instrucciones
Atlas Copco
Atlas Copco RRD 37-11 Manual de usuario
Atlas Copco
Atlas Copco RRF 31 Manual de usuario
Atlas Copco
Atlas Copco PRO P2536-H Manual de usuario
Atlas Copco
Atlas Copco ETP TBP131-150-13 Manual de usuario
