ATEN Master View ACS-1602 Manual de usuario

User Manual

ACS-1602

Read this guide thoroughly and follow the installation and operation

procedures carefully in order to prevent any damage to the unit and/or

any devices that connect to it.

This package contains:

M1 ACS-1602 ADC KVM Switch

M2 ADC Cables (1.8m)

M1 User Manual

M1 Quick Start Guide

If anything is damaged or missing, contact your dealer.

Manual Part No. PAPE-1211-1AT

Printed in Taiwan 04/2003

All brand names and trademarks are the registered property of their respective owners.

2003-04-22

Note: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy, and if not installed and

used in accordance with the instruction manual,may cause

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more

of the following measures:

MReorient or relocate the receiving antenna;

MIncrease the separation between the equipment and

receiver;

MConnect the equipment into an outlet on a circuit different

from that which the receiver is connected;

MConsult the dealer or an experienced radio/television

technician for help.

2003-04-22

Overview

The Master View ACS-1602 ADC KVM Switch is a two port

control unit that allows access to two ADC equipped Macintosh

systems from a single ADC console (USB keyboard, USB

mouse, and ADC display).

DVI equipped PCs can also be accessed from the ADC console

with the use of an ADC to DVI adapter.

ADC (Apple Display Connector) is a digital interface

implementation that is proprietary to Apple®Computer. Apple’s

Cinema and Studio flat panel displays utilize the ADC

connector interface with the latest Mac systems. The ACS-1602

supports both of those displays. It also supports analog CRT

ADC monitors.

Setup is fast and easy; plugging the ADC cables into their

appropriate ports is all that is entailed. There is no software to

configure, no installation routines, and no incompatibility

problems.

The digital video, USB, and power signals are transported via

the single ADC cable. This eliminates the desktop clutter

associated with traditional cable hookups, and makes for a neat

and tidy workspace.

Access to the two computers is quick and convenient. Pressing

the push button Port Selection Switch located on the unit’s top

panel toggles the KVM focus between them.

There is no better way to save time and money than with a

Master View ACS-1602 installation. By allowing a single

console to manage both computers, the ACS-1602 eliminates

the expense of purchasing a separate keyboard, video display,

and mouse for each one. Additionally, it saves the extra space

and energy costs that they would require, and eliminates the

inconvenience and wasted effort involved in constantly having

to move from one computer to the other.

- 1 -

2003-04-22

Features

MProvides control of two ADC enabled computers from a

single ADC console (ADC Display, USB keyboard, USB

mouse).

MSupports all 15,17, 22, and 23 inch Apple® ADC Cinema &

Studio Displays.

MSupports 19 inch analog CRT ADC monitors.

MEasy to install - no software required - simply connect the

ADC cables.

MEasy to operate - computer selection via push button switch.

MSupports Mac OS 9.2 and higher

MSupports Windows 98SE and higher.*

MUp to 1920 x 1200 Resolution; DDC, DDC2, DDC2B

MLED display for easy status monitoring.

MSaves time, space, power, and equipment costs.

MNon-powered.

*On DVI equipped PCs using an ADC to DVI adapter

(requires separate purchase).

- 2 -

WARNING!

Components on an ADC connection are NOT hot

pluggable. To add or remove components the

Installation and Powering Off sequences described in

this manual (pages 6 and 10) must be followed.

Failure to do so will result in damage to the

components.

2003-04-22

Hardware Requirements

Console

MAn ADC Cinema or Studio Display; or an analog ADC CRT monitor

MA USB Keyboard

MA USB Mouse

Computer

Either an ADC equipped Mac, or DVI equipped PC with an

ADC to DVI adapter (see the Cables section, below).

Cables

Because the ACS-1602 supports both digital and analog

signals, the integrated (digital and analog) Custom Cable sets

provided with this package must be used to connect the Master

View ACS-1602 to the computers. Standard ADC cables

cannot be used.

The ADC cable carries video signals, USB signals, and power.

It is compatible with DVI graphics cards, but requires the

installation of an ADC to DVI adapter that separates out the

USB and power signals (see the diagram on p. 8).

Note: 1. An ADC to DVI adapter is not part of the ACS-1602

package. It must be purchased separately.

2. If you use an ADC to DVI adapter make sure that the

adapter and the PC’s DVI VGA card are both digital or

both analog devices.

3. Mac Cube, G3 and G4 systems support both analog

and digital signals.

- 3 -

2003-04-22

Components

Front View:

1. Port Selection Switch

Press this switch to toggle the KVM focus between the two

ports.

2. Port LEDs

MThe On Line LED lights ORANGE to indicate that the

computer connected to its corresponding port is up and

running.

MThe Selected LED lights GREEN to indicate that the

computer connected to its corresponding port is the one

that has the KVM focus.

3. ADC Console Port

The cable from your ADC display plugs in here.

- 4 -

2003-04-22

Rear View:

1. ADC Port 2

The cable that connects to the ADC port on the computer

you are designating as Computer 2 plugs in here.

2. ADC Port 1

The cable that connects to the ADC port on the computer

you are designating as Computer 1 plugs in here.

- 5 -

2003-04-22

Installation

To set up your ACS-1602 installation, refer to the diagram

below and the one on p. 8 as you do the following:

1. Plug your USB keyboard and USB mouse into the USB ports

on the back of the ADC display.

- 6 -

1. Before you begin, make sure that power to all the

devices you will be connecting up have been

turned off. You must unplug the power cords of any

computers that have the Keyboard Power On

function. Otherwise, the switch will receive power

from the computer.

2. To prevent damage to your installation due to ground

potential difference, make sure that all devices on the

installation are properly grounded.

3. When starting up your installation, you must follow the

connecting up and powering On sequence described

in these installation instructions. Failure to do so will

result in damage to the equipment.

2003-04-22

2. Plug the cable from the ADC display into the Console port

connector of the Master View ACS-1602.

3. Use the ADC cables provided with this package to connect

the ACS-1602’s ADC ports to the ADC ports of the

computers you are installing.

Note: If your computer uses a DVI type connector, you will

have to use an ADC to DVI adapter (requires

separate purchase). Refer back to the Note in the

Cables Section on p. 3, for details.

4. Turn On the power to the computers.

5. Turn On the ADC Display.

Powering On Considerations:

1. When you Power On, the Display and the computers take a

few moments to establish their communication parameters.

You must wait until the procedure completes (i.e., the

desktop finishes coming up and is ready to accept computer

input) before changing ports. Otherwise, when you switch

back to the original port, the display will either be blank or

distorted.

If this occurs, you must Power Off the system (see p. 10),

and Power it back On (see steps 4 and 5, above).

2. The Power On default is to link to ADC Port 1. If the

computer attached to port 1 is inactive, the display will be

blank so it may appear as if the unit is not functioning. This is

not the case. Simply press the Port Selection switch to

toggle the KVM focus to the active computer on port 2.

- 7 -

2003-04-22

- 8 -

ADC-to-DVI Adapter

AC Power

Mac

DVI

USB

2003-04-22

Tabla de contenidos

Otros manuales de Cambiar de ATEN

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario