Atec PMM PA6001 Manual de usuario

NARDA

Safety

Test

Solutions

S.r.l. Socio Unico

Sales & Support:

Via Leonardo da Vinci, 21/23

20090 Segrate (MI) - ITALY

Tel.: +39 02 2699871

Fax: +39 02 26998700

Manufacturing Plant:

Via Benessea, 29/B

17035 Cisano sul Neva (SV)

Tel.: +39 0182 58641

Fax: +39 0182 586400

http://www.narda-sts.it

SERIAL NUMBER OF THE INSTRUMENT

You can find the Series Number on the rear panel of the instrument.

Series Number is in the form: 0000X00000.

The first four digits and the letter are the Series Number prefix, the last five digits are

the Series Number suffix. The prefix is the same for identical instruments, it changes

only when a configuration change is made to the instrument.

The suffix is different for each instrument.

User’s Manual

PMM PA6001

WIDEBAND RF POWER

AMPLIFIER

100 kHz - 250 MHz / 40 Watts

Provided by: www.atecorp.com

(800) 404-ATEC

Advanced Test

Equipment Rentals

II Note and symbols

NOTE:

Do not use the equipment in a function not specified by the manufacturer.

This instruction manual must be read before attempting to install or operate the amplifier.

Before using the equipment the user must insure that all instructions at switch on as indicated in chapter 2 have

been properly made and checked.

The information contained in this document is subject to change without notice.

SAFETY SYMBOLS:

Warning, danger of electric shock

Read carefully the Operating Manual and its instructions, pay attention to the safety

symbols.

EARTH PROTECTION

Contents III

Contents

General safety considerations and instructions.........

EC Declaration of Conformity …………………………...

1 General information

1.1 General information…...........................….................

1.2 Main specifications.........................…........................

Page

1-1

1-2

2 Installation

2.1 Mains supply cable...............................…..................

2.2 Auxiliary earth conductor connection....….................

2.3 Air intake and escape (in house installation).............

2.4 Weight of the equipment.......................….................

2.5 Moving of the equipment…….....................…............

2.6 RF interconnections…………………………………….

2.7 Switch on (for 1st check step)………………………….

2.8 Switch off (for 1st check step)………………………….

Page

2-1

2-2

3 Instructions for use

3.1 Front panel in standard configuration.........................

3.2 Operation instructions....….........................................

3.2.1 Switch on.................................................................

3.3 Operation....................…............................................

3.3.1 Power measurement ……...............…...................

3.3.2 Excess direct power ……….……………………..…

3.3.3 Mismatch …….……………………………………....

3.3.4 Temperature ….………………...............................

3.3.5 Switch off....................…........................................

Page

3-1

3-2

4 Maintenance

4.1 1st Level maintenance...........................…..................

4.2 Preventive maintenance…………….....…..................

Page

4-1

IV Contents

Figures

Figure

1-1

3-1

4-1

PA6001 ………….………………………………

PA6001 Auxiliary earth conductor connection

PA6001 front panel……………………………..

Page

1-1

3-1

4-1

Tables

Table

1-1

Main Specifications PA6001…………………..

Page

1-2

Safety consideration V

SAFETY RECOMMENDATIONS AND INSTRUCTIONS

To maintain it in safe conditions and ensure correct use, these general instructions must be fully

understood and applied before the product is used.

•CAT 1 Terminals are present on the equipment; do not use for categories of measurement II, III and

IV.

•High leakage current equipment, connect the protective earth terminal before connection to mains.

•Hazardous live voltage are present at the outputs of the amplifier, connect load(s) to the amplifier

outputs before using.

•Install the equipment in a shielding zone to meet the emission specifications of the directive

2004/108/CE. Inside the shielding area, other test equipments could be disturbed.

•For safety reasons, do not leave the equipment under mains voltage when the RF output is not

connected.

•Before using the amplifier, the input level of the signal generator must be checked (0 dBm typical, +

10 dBm max.).

•Special care must be taken with regards to the level of radiation of all equipments connected to the

amplifier.

•For the operator safety, do not connect or disconnect the load when the amplifier delivers the RF

signal.

•When the amplifier is in the “RF ON” mode and during any change of input signal conditions, special

care must be taken against transient and spurious signals generation.

•Connect terminal loads (50 Ω) with adequate power capability (see output power curves in calibration

document) when the amplifier is operating.

VI EC Conformity

Dichiarazione di Conformità

EU Declaration of Conformity

In accordo alla Decisione 768/2008/EC, conforme alle direttive EMC 2014/30/UE, Bassa Tensione 2014/35/UE e

RoHS 2011/65/UE, ed anche alle norme ISO/IEC 17050-1 e 17050-2.

In accordance with the Decision 768/2008/EC, compliant to the Directives EMC 2014/30/EU, Low Voltage 2014/35/EU and

RoHS 2011/65/EU, also compliant to the ISO/IEC standard 17050-1 and 17050-2

Il costruttore

The manufacturer narda Safety Test Solutions S.r.l. Socio Unico

Indirizzo

Address Via Benessea, 29 / B

I-17035 Cisano sul Neva (SV) - Italy

sulla base delle seguenti norme europee armonizzate, applicate con esito positivo:

based on the following harmonized European Standards, successfully applied:

EMC - Emissioni:

EMC - Emission: EN 61326-1 (2013)

EMC - Immunità:

EMC - Immunity: EN 61326-1 (2013)

Sicurezza:

Safety: EN 61010-1 (2010)

dichiara, sotto la propria responsabilità, che il prodotto:

declares, under its sole responsibility, that the product:

Descrizione

Description

AMPLIFICATORE DI POTENZA

POWER AMPLIFIER

Modello

Model PA 6001

è conforme ai requisiti essenziali delle seguenti Direttive:

conforms with the essential requirements of the following Directives:

Bassa Tensione

Low Voltage 2014/35/EU

Compatibiltà Elettromagnetica

EMC 2014/30/EU

RoHS

RoHS 2011/65/EU

Cisano sul Neva, 3 May 2017

Egon Stocca, General Manager

General Information 1-1

1 - General Information

1.1 General Information The PA6001 amplifier is an up-to-date and high-performance equipment

leading to all kinds of applications:

- EMC tests of radiated susceptibility (antennas, striplines, TEM and GTEM

cells, etc),

- EMC tests of conducted susceptibility, according to each type of

couplings

- Direct coupling,

- Capacitor coupling ,

- Inductor coupling,

- Transformer coupling,

- All types of modulation: AM, FM, pulse modulation,

- IEMN pulse tests (Damp Sine, Single-pole bi-exponential, etc).

The PA6001 amplifier is manufactured to operate in a CW mode (CW) with

a single instantaneous range from 100 kHz to 250 MHz.

The typical output power is about 40 watts minimum on a 50 ohms load.

The equipment operates under any VSWR conditions. It can deliver a high

RF current under short circuit conditions and a high voltage under open

circuit conditions. This key feature makes the amplifier PA6001 a high

performance tool with a high degree of safety.

The bandwidth is instantaneous. This allows to use a sweep frequency

generator or to amplify large frequency spectrum signals. Consequently,

no adjustment of the amplifier is necessary.

Fig. 1-1 PA6001

Document PA6001EN-70601 - NARDA 2017

1-2 General Information

1.2 Main specifications

TABLE 1-1 Technical specifications

Frequency bandwidth

Typical output power

Power at 3 dB compression

Power at 1 dB compression

Harmonics distortion

Class type

Gain

Linear power gain flatness

Mismatch tolerance

Input impedance

Output impedance

Input power

RF input connector

RF output connector

Ambient operating temperature

Room temperature storage

Cooling

Power voltage

Rated current

Dimensions

Weight

100 kHz – 250 MHz

40 W

40 W min. up to 100 MHz / 35 W min. from 100 MHz to 250 MHz

35 W min. up to 100 MHz / 30 W min. from 100 MHz to 250 MHz

H2, H3 < -20 dBc for the output power at 1 dB compression limit

Class A

43 dB

± 3 dB max

Infinite without damage

50 Ω/ VSWR: 2:1max

+ 10 dBm max.

Type N fem. (front or rear panel) – other connector type on request

0 °C / + 35 °C

-20 °C / + 70 °C

Forced air: 20 l/sec max. (self contained fans)

90 – 250 Vac, 47 – 63 Hz, single phase

2 A @ 230 Vac

438 x 410 x 125 mm (3U) / 17.2 x 16.1 x 4.9 in (3U)

12 kg / 26.4 lb

Installation 2-1

2 - Installation

2.1 Mains supply cable The mains cable is connected to a single phase network (16A min +

neutral + ground). The typical current measured when the amplifier is in RF

ON mode (amplification is active) is :

110 Vac : = 3.7 Amps AC / / 230 Vac : = 1.8 Amps AC

Use a plug with minimum rating of 16 A min.

Installation requirements on which the equipment is connected: low

voltage installation to IEC 60364 (NFC15-100).

High current leakage equipment.

Connect the auxiliary earth conductor to the protective ground before

switching on the equipment.

2.2 Auxiliary earth

conductor connection

See below how to connect the auxiliary earth conductors

Fig. 2-1 PA6001 Auxiliary earth conductor connection

2.3 Air intake and escape

(in house installation)

The air intake is allowed via the front panel and the sides of the equipment.

The air exhaust is provided on the rear panel (horizontal air flow). It is

imperative to avoid any air flow obstruction and to allow air exhaust toward

the front panel and the sides of the equipment.

The rear panel of the amplifier must be located at 1 meter minimum

from any wall, except in case of air forced extract

2.4 Weight of the

equipment

Heavy equipment

This equipment weighs 10 kg, the tables or cabinet where it will be

installed must be capable of supporting this weight.

Document PA6001EN-70601 - NARDA 2017

2-2 Installation

2.5 Moving of the

equipment

In the event of displacement, first of all switch off the amplifier, disconnect

the equipment of the electrical supply network, then all the external cables

(including the connections of ground) must be removed

2.6 RF interconnections

The cables used must be of a sufficient quality to allow operation up to

1000 MHz and to withstand the power delivered by the amplifier. The

connectors recommended are N male for output power connections and N

male for input power. The characteristic impedance of the cable must be

50 Ωin order to allow maximum power operation. As this equipment will be

used in an EMC test environment, we recommend using cable as short as

possible and with a length less than 3 meters

2.7 Switch on

(for 1st check step)

For this simple check step, connect a 50 Ωload to the RF input and output

connectors.

Execute the following operations to switch on the amplifier :

- Install the mains supply cable,

- Push the button "POWER",

- Verify the fans switch on on the rear panel.

For safety reason, do not switch on the equipment if its input and

output are not connected to an adequate 50 Ωload.

2.8 Switch off

(for 1st check step)

Press the "POWER" button to completely stop the amplifier.

Please refer to Chapter 3 for the user operation instructions.

Otros manuales de Amplificador de Atec

Atec

Atec 5104 Manual de usuario

Atec

Atec CMX25 Manual

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario