AT&T 984QSG Manual de usuario

This Quick Start Guide provides basic instructions. For additional

installation options and complete instructions which allow you to use

all features of this phone, refer to your AT&T Small Business System

Speakerphone with Digital Answering System and Caller ID/Call

Waiting 984 User's Manual, Part 2.

Installation

Installation of a DSL splitter may be required to use the advanced

features of this telephone if you have DSL (digital subscriber line)

service. Please see DSL users starting on page 4 of your User’s

Manual, Part 2 for details.

If you are installing multiple phones in your phone system, you must

install and program one set at a time. Each phone MUST be assigned

a unique extension number.

Battery installation

Install a 9V alkaline battery (purchased separately) in order to use some features

of this telephone in the event of a power failure. If power fails and a working

battery is installed, all four lines of this phone will work only to answer calls

with the handset or headset, and to dial calls using the dial pad keys and the

one touch or redial features. No other features will work until power is

restored.

1. Remove the wedge from the underside of the base unit. Press

on the tabs and pull the wedge away from the phone.

continued on page 2

QUICK START GUIDE

AT&T Small Business System

Speakerphone with Digital Answering

System and Caller ID/Call Waiting 984

984QSG_(Rev6)ml23.05.06 5/23/06 11:27 AM Page 1

Battery installation

continued from page 1

2. Remove the battery compartment screw with a small Phillips

head screwdriver.

3. Pull on the tab to remove the battery compartment cover.

4. Insert a 9V battery (purchased separately) following the

polarity markings in the battery compartment.

5. Replace the battery compartment cover and the screw.

6. Reattach the wedge to the base unit by sliding the tabs into the

holes. Snap the wedge onto the base.

Table/desk installation

For best results, follow the directions in Battery installation beginning on

page 1 of this Quick Start Guide before installing the phone.

Recommended wiring configuration for phone system

NOTE: The total length of telephone wire used in your system should not

be more than 600 feet as it may cause interference with the advanced

features of this telephone.

NOTE: Users should use ONLY the line cords provided. .

1. Connect the telephone line cords to the telephone and wall

jacks as shown in the following illustration on page 3.

984QSG_(Rev6)ml23.05.06 5/23/06 11:27 AM Page 2

•Four one-line jacks (To use this installation option, you’ll need

to purchase two two-line adapters. Adapters are available at retail

stores or by calling 1 (800) 222–3111.)

•Two two-line jacks

2. Connect the handset cord.

Plug one end of the coiled handset cord into the jack on the left

side of the phone. Plug the other end into the handset and hang up.

continued on page 4

Two-line adapters

Telephone

line cords

Modular telephone

jacks lines 3 and 4 Modular

telephone jacks

lines 1 and 2

L1/L2 jack

L3/L4 jack

Modular

telephone jack

lines 3 and 4

Modular telephone

jack lines 1 and 2

Telephone

line cords

L1/L2 jack

L3/L4 jack

984QSG_(Rev6)ml23.05.06 5/23/06 11:27 AM Page 3

Table/desk installation

continued from page 3

3. Connect the power adapter to the telephone.

Use only the power adapter provided with this product.

To obtain a replacement, call 1 (800) 222–3111.

Plug one end of the power adapter into the jack labeled POWER

on the back of the phone. Plug the other end into a standard

electrical outlet not controlled by a wall switch.

4. Initialization.

If no battery is installed when you connect the power cord, the phone

runs a quick self-test and the screen displays Initializing for about

seven seconds.

NOTE: The phone will run through this same initialization any time it is

reconnected to AC power if a working battery is not installed (for example,

after a power failure or when the unit has been unplugged).

5. Check for dial tone.

Lift the handset and listen for a dial tone. If you cannot hear a dial

tone, please see In case of difficulty beginning on page 121 of your

User’s Manual, Part 2 for details.

Standard

electrical

outlet

Power adapter

Power jack

984QSG_(Rev6)ml23.05.06 5/23/06 11:27 AM Page 4

Feature setup

Feature setup, memory programming and some individual

feature operations for the 984 use menus shown in the

screen display. For detailed instructions for using the menus,

see Menu operation beginning on page 22 of your User’s

Manual, Part 2.

Assign an extension number to

your phone

Every individual phone in your telephone system MUST be

assigned a unique extension number for the intercom feature

to work.

1. Press Eto begin feature setup.

2. Press -until the screen display includes

PHONEHSETTINGS.

3. Press E. The screen display includes

EXTENSIONHNO and the current setting.

4. Press <or >to change the extension

number (11h…h26).

5. When the desired extension number is shown,

press -to save your choice. The screen display

includes RINGERHON/OFF.

NOTE: If you duplicate an extension number already in

use, you will hear a repeating short ring (error ring) and

the screen display will include EXThXXhishalready

usedhAssignhnewhEXTh#hif the phone is in idle mode.

If the phone is in the programming mode, you will hear the

repeating short ring only. Repeat steps 1-5 at the ringing

phone to assign a different extension number (from

11-26).

6. Press and hold Eto return to the idle screen.

NOTE: You can exit feature setup and return to the idle

screen any time. Simply press and hold E.

984QSG_(Rev6)ml23.05.06 5/23/06 11:27 AM Page 5

Turn line usage on or off for each

line

If you are not using all four phone lines at this extension,

you need to turn off line usage for the unused lines. If you

expand to a second, third or fourth line, turn line usage back

on. Line 1 must be turned on for the intercom to work.

NOTE: You may use any combination of lines. Lines used

do not need to be in order. For example, line usage can

be turned on for Lines 1 and 3 and turned off for Lines 2

and 4.

You may also restrict the use of certain lines on this phone to

intercom and paging only, by turning off line usage for each

line you want restricted. When line usage is turned off, that

line cannot be used to answer incoming calls or to make

outgoing or transfer calls.

1. Press Eto begin feature setup.

2. Press -until the screen display includes

SPECIALHOPTIONS.

3. Press E. The screen display includes

LINEHUSAGE.

4. Press E. The screen display includes

L1HUSAGE and the current setting for this line.

5. Press <or >to toggle between On and Off for

the line shown.

6. Press -to save the current setting for this line

and move to the next line with its current line

usage setting.

7. Repeat steps 5 and 6to set line usage for other

lines at this extension.

8. When you are finished setting line usage, press -

until the screen display includes DONE.

9. Press E. The screen display includes

LINEHUSAGE.

10. Press and hold Eto return to the idle

screen.

NOTE: You can exit feature setup and return to the idle

screen any time. Simply press and hold E.

984QSG_(Rev6)ml23.05.06 5/23/06 11:27 AM Page 6

Program home and local area codes

You can program this phone to recognize one home and

up to five local area codes. See Home area code and

Local area code on page 6 of your User’s Manual, Part 2

for definitions.

1. Press Eto begin feature setup.

2. Press -until the screen display includes

SPECIAL OPTIONS.

3. Press E. The screen display includes

LINE USAGE.

4. Press -until the screen display includes

AREA CODES.

5. Press E. The screen display includes

HOMEHAC and a prompt to enter a three-digit

home area code.

6. Use the dial pad keys to enter your home area

code, then press -. The screen display includes

LOCALhAC1 and a prompt to enter a three-digit

local area code.

If you need to enter any local area codes, use the

dial pad keys and then press -to scroll to the next

screen (LOCALhAC2,hLOCALhAC3,hLOCALhAC4,

andhLOCALhAC5).

NOTE: If you must dial the area code to place calls

within your own area code, enter 000 for the home area

code and enter your area code as a local area code.

7. When you are finished entering all of the area

codes you need to program, press -until the

screen display includes DONE.

8. Press E. The screen display includes

AREA CODES.

9. Press and hold Eto return to the idle screen.

NOTE: You can exit feature setup and return to the idle

screen any time. Simply press and hold E.

984QSG_(Rev6)ml23.05.06 5/23/06 11:27 AM Page 7

Telephone operation

NOTE: This phone comes programmed to use line 1

(default prime line) for calls if you do not press a LINE

button. (To change the prime line, see Assign the

prime line on page 34 of your User’s Manual, Part 2.)

When you answer a call, the phone automatically selects

the ringing line.

Make or answer a call using the

handset

NOTE: If you dial a phone number longer than 15 digits,

the screen will display only the last 13 digits.

To make a call, lift the handset and dial the call.

To answer a call, lift the handset. Replace the handset to

end the call.

To override automatic line selection, press the LINE

button for the line you wish to select, then lift the handset.

Make or answer conference calls

Please refer to page 65 of your User's Manual, Part 2 for

more details in setting up conference calls.

NOTE: The outside line call must be established first

because an intercom call cannot be placed on hold.

NOTE: If you are experiencing difficulty in using the

conference features on this phone, please consider using

AT&T's complete line of teleconference services to find a

solution that best meets your needs. AT&T

TeleConference Services reduces travel time and expense

while increasing productivity wherever people are located,

allowing you to host truly virtual meetings and share

important information in real time. To sign up for AT&T

TeleConference Services, go to:

www.att.com/orderconference for details.

984QSG_(Rev6)ml23.05.06 5/23/06 11:27 AM Page 8

One touch operation

This telephone has 32 one touch locations where you can store phone numbers

you wish to dial using fewer keys than usual. You can store up to 24 digits in

each location. The steps used to dial numbers stored in one touch locations

vary according to how you programmed the one touch preference. See Set

one touch preference on page 25 and Dial a one touch number on page

74 of your User’s Manual, Part 2 for more details.

The first 16 locations can be accessed using only the EXT buttons. To access

the remaining 16 locations, press Wand then the EXT button for the

desired location.

NOTE: The EXT buttons are also used to place intercom calls. See

Intercom operation beginning on page 83 of your User’s Manual, Part 2

for details.

You may wish to write the names or telephone numbers of one touch entries

on the directory card, using the light gray spaces for the first 16 locations and

the dark gray spaces for the second 16 locations.

locations

(all dark gray spaces)

EXT buttons

LOWER button

16 one touch locations

(all light gray spaces)

16 lower one touch

984QSG_(Rev6)ml23.05.06 5/23/06 11:27 AM Page 9

Store a number in a one touch

location

For information about using the screen menus, see Menu

operation beginning on page 22 of your User’s Manual,

Part 2.

1. Press Eto enter the feature menu.

The screen displays ONEhTOUCH.

2. Press E. The screen display includes

PREFERENCE and the current setting.

3. Press -until the screen display includes

PROGRAM.

4. Press E. The screen display includes

<Enterhnumber>.

5. Enter the phone number using the dial pad keys.

—OR—

Press Rto copy the last number dialed

from this extension to this location.

The screen will show the number as you enter it.

You can press <to backspace.

6. When you are finished entering the number, choose

a one touch location:

Press the EXT button.

—OR—

Press W, then press the EXT button.

The screen displays the number entered and

Stored!.

NOTE: Only the last number dialed from this extension

can be copied to a one touch location. The other

numbers in the redial stack cannot be copied.

NOTE: You can store a pause, flash or touch tone signals

in a one touch entry. Please refer to page 72 of your

User's Manual, Part 2 for more details.

NOTE: You can exit storing a number at any time.

Press -until the screen shows CANCEL, then press

—OR—

Press and hold E.

984QSG_(Rev6)ml23.05.06 5/23/06 11:27 AM Page 10

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Teléfono de AT&T

AT&T

AT&T TL90031 Manual de usuario

AT&T

AT&T 410 820 Manual de usuario

AT&T

AT&T Four-Line Intercom Speakerphone 944 Manual de usuario

AT&T

AT&T MLC-5 Manual

AT&T

AT&T MDC 9000 Manual de usuario

AT&T

AT&T 993 2-Line Manual de usuario

AT&T

AT&T CL4940 Manual de usuario

AT&T

AT&T CL2909 Manual de usuario

AT&T

AT&T CL2939 Manual de usuario

AT&T

AT&T CN5345 Manual de usuario

AT&T

AT&T 929 Manual de usuario

AT&T

AT&T TL86109 Manual de usuario

AT&T

AT&T Definity ISDN 7505 Manual de usuario

AT&T

AT&T 1477/1177 Manual de usuario

AT&T

AT&T CL82115 Manual de usuario

AT&T

AT&T U-verse TV Manual de usuario

AT&T

AT&T E5960C Manual de usuario

AT&T

AT&T CL82143 Manual de usuario

AT&T

AT&T TL80133 Manual de usuario

AT&T

AT&T EL52265 Manual de usuario

AT&T

AT&T 1855 - AT&T Corded Phone Manual de usuario

AT&T

AT&T Legend Setup For Merlin Mail Manual de usuario

AT&T

AT&T 1070 Manual de usuario

AT&T

AT&T 145 Manual de usuario

Manuales populares de Teléfono de otras marcas

GE 2-9480 Manual de usuario

Geemarc

Geemarc PHOTOPHONE 155 Manual de usuario

D-Link

D-Link DWR-720/PW Manual de usuario

Interquartz

Interquartz Gemini IQ333 Manual de usuario

SSS Siedle

SSS Siedle HT 840-0 Manual de usuario

Motorola

Motorola TITANIUM Manual de usuario

Panasonic

Panasonic ICX Manual de usuario

LG H870DS Manual de usuario

Samsung

Samsung GT-I9500 Manual de usuario

Selta

Selta zenyth 600 Manual de usuario

Doro

Doro AFTI 20 Manual de usuario

UNIQCELL

UNIQCELL A1 Manual de usuario

Panasonic

Panasonic KX Series Manual de usuario

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Manual de usuario

BT Decor 425 Manual de usuario

NEC

NEC SV8500 Manual de usuario

Teledex

Teledex PEARL Manual de usuario

Ericsson

Ericsson Dialog 3213 Manual de usuario