AT&T PagePac Plus Guía de inicio rápido
463-248-201
Issue 1
3/1/93
PagePacPlus Controller
Installation and Use
Copyright 1993 AT&T
All Rights Reserved
Written/Printed in U.S.A.
AT&T 463-248-201
011722051-000
Issue 1, March 1993
Notice
Every effort was made to ensure that the information in this guide was complete and accurate at the time of printing.
However, information is subject to change.
Federal Communications Commission (FCC) and Canadian Dept. of Communications Interference Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC rules and D.O.C. regulations. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction guide, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to clause
harmful interference, in which case the user will have to correct the interference at his or her own expense. For
additional FCC interference, registration, and repair information, see the
Installation Guide.
Trademarks
PAGEPAC, PAGEPAC PLUS, and AMPLICENTER are a trademark of Harris Corporation.
Warranty
AT&T provides a limited warranty for this product. Refer to “AT&T Limited Warranty and Limitation of
Liability” in Appendix A.
Ordering Information
The order number for this book is 463-248-201. To order copies of this book, call 1-800-432-6600 in the U.S. and
1-800255-1242 in Canada. For more information on how to order this and other system reference materials, see
“Reference Materials,
‘‘ in “About This Guide.”
For information on ordering replacement parts, accessories, and
other compatible equipment, refer to “Product Ordering Information,” in Section 1.
Support Telephone Numbers
AT&T provides a toll-free customer helpline 24 hours a day.
In the U.S., call the AT&T Helpline at 1-800-628-2888 if you need assistance when installing, programming, or
using your system. For service or technical assistance in Canada, call one of the following Technical Assistance
Centers:
Eastern Canada and Ottawa
1800363-1882
Ontario:
1-800-3874268
Central and Western Canada:
1-800-663-9817
VG—3/93—2.4M
Contents
1.
Overview
1-1
■
■
■
■
■
■
About This Guide
How to Use This Guide
Installation Steps
Connectivity Chart
Product Safety Labels
Terminology
Reference Materials
How to Comment on This Guide
Shipping Container Contents
Ordering Information
Features and Capabilities
Specifications
■
■
■
■
■
■
1-3
1-3
1-4
1-6
1-8
1-8
1-8
1-8
1-9
1-9
1-10
1-12
2.
Hardware Configuration
■ Power
■ Tone Generator
■ Circuit Protection
■ Mounting
■ Universal Approvals
■ Controls, Indicators,
■ Auxiliary Equipment
2-1
2-2
2-2
2-2
2-2
2-2
Switches and Connectors
2-3
2-6
iii
3.
Installing the Hardware
3-1
■
■
■
■
■
■
■
Important Safety Information
Example System Setup
Mounting PagePac Plus Components
Zone Configurations
Speaker Connections
Paging Zone Connections
Contact Closure Zone Connections
Switch Settings
Interconnection Considerations
Communication System Interface
Music Source Interface
Programming Overview
Testing System
3-3
3-4
3-8
3-11
3-11
3-11
3-15
3-15
3-16
3-18
3-20
3-20
3-20
■
■
■
■
■
■
4.
Maintenance and Customer Support
■ In Case of Difficulty
■ Power Failure Operation
■ Common Problems
■ Troubleshooting
4-1
4-2
4-2
4-3
4-3
A.
FCC Statement/Registration and Warranty Information
A-1
B.
Feedback Form
B-1
IN
Index
IN-1
iv
Figures
1.
Overview
1-1
1-1.
Hardware Installation Steps
1-5
1-2. PagePac Plus System Components
1-11
2.
Hardware Configuration
2-1. Controller, Amplicenter, and Zone Expansion Unit
Back Panels
2-1
2-5
3.Installing the Hardware
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
70 Volt Constant Voltage Distribution
Controller System Setup
Hybrid System Setup
Wall Mounted Hardware
Rack Mounted Hardware
Speaker Zone Wiring to Controller
System
Contact Closure Zone Wiring to Controller
Setup
3-1
3-5
3-6
3-7
3-9
3-10
3-12
3-14
vi
Overview
1
Overview 1-1
“This page intentionally left blank”
The following subsections give a summary of the PagePac Plus controller
features, system components, and auxiliary equipment.
About This Guide
How to Use This Guide
The PagePac Plus Paging Controller Installation and Use Guide explains
the features of the PagePac Plus Controller, how to install and configure
the controller, installation of the PagePac Plus amplicenter, and interface
to communication system and other auxiliary equipment. For programming
instructions, refer to the PagePac Plus Programming and Operation Guide.
It is intended that PagePac Plus be installed by a trained telephone, audio,
or electrical installer with basic electronic knowledge. PagePac Plus
conforms to common installation practices and preferences found within
the Telcom Electrical and Commercial Sound installers manual.
■
■
■
■
Overview. Before beginning hardware installation, review and
understand the Zone Map filled out in the PagePac Plus Programming
and Operation Guide. It determines how the hardware is to be
installed and set.
If you are installing the system for the first time, you should read the
entire guide before getting started to familiarize yourself with the
features.
Hardware Configuration. This section describes and illustrates the
various PagePac Plus components (controller, zone expansion units,
and Amplicenter amplifiers, D20, D100, and D300).
System Installation. This section provides instructions for mounting
the PagePac Plus hardware on a wall or in a standard 19“ equipment
rack. Complete, detailed instructions for connection and operation with
telephone systems, music source, speakers, and any control device
inputs or outputs is provided. Hardware switch settings are given for
various zone applications. A programming overview is presented.
Maintenance and Customer Support. This section gives some basic
troubleshooting tips if a zone does not operate properly after
installation and programming. Should a problem arise which requires
technical assistance beyond the information provided in this guide, call:
AT&T Technical Support, 1-800-552-3293
AT&T National Technical Marketing, 1-800-222-1313
AT&T National Service Assistance Center, 1-800-628-8888.
Overview 1-3
Installation Steps
1.
2.
3.
4.
NOTE: The numbers in these
5.
steps match the numbers in
figure 1-1.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Determine PagePac Plus features to be used in the facility. Refer to
the Zone Map and Zone Configuration Tables filled out in the
Programmer’s Guide.
Verify Zone Map information matches facility wiring diagram.
Pull cables.
Mount the PagePac Plus components [Amplicenter, Controller and
Zone Expansion Unit(s)], to either the wall, cabinet or a rack.
Make the connection between the Controller and Amplicenter, and
Controller and Zone Expansion Unit (if any).
Set the DIP switches on the Zone Expansion Unit(s) [if needed].
Using the Zone Configuration Table, set the Zone Option Switches
on the Controller and the Zone Expansion Unit(s) to the correct
settings.
Set the Controllers Telephone Mode Selection Switch to the correct
position for the host telephone system.
If the system is used in the Constant Voltage Distribution Mode (i.e.
70 volt speakers), make connection and set the Amplicenter
Telephone Mode Selection Switch to the Dry Loop 600 Ohm position.
Connect all necessary feature inputs (microphone, night bell, etc.,).
Using the Zone Map Table, connect speakers, remote amps and
inputs to the proper zones.
Power up the system.
Check LED’s on PagePac Plus system for proper operation.
Make the telephone connection.
Perform Programming.
Test system:
A – Audio paging Zones
B – Contact Closure Output Zones
C – Contact Closure Input Zones.
1-4 Overview
Otros manuales para PagePac Plus
1
Tabla de contenidos
Otros manuales de Controladores de AT&T
