Asus M2400NE Manual de usuario

DISASSEMBLY PROCEDURE

2 - 1

Chapter

Disassembly Procedure

Please follow the information provided in this section to perform the

complete disassembly procedure of the notebook. Be sure to use

proper tools described before.

SUS M2400Ne (ID1) Series Notebook consists of various modules. This

chapter describes the procedures for the complete notebook disassembly. In

addition, in between procedures, the detailed disassembly procedure of

individual modules will be provided for your service needs.

The disassembly procedure consists of the following steps:

•Battery module

•Optical drive Module

•HDD Module

•Memory Module

•CPU Module

•Keyboard Module

•Mini-PCI Module

•LCD Module

•Top Case Module

•Motherboard Module

•Modem Module

•Bottom Case Module

DISASSEMBLY PROCEDURE

2 - 2

Battery module

The illustration below shows how to remove the battery module.

1. Slide the battery latch and lift the battery away from the system.

Optical Drive Module

1. Push the latch and pull the DVD-ROM module out.

HDD Module

The illustrations below show how to remove the HDD module from the notebook.

Removing HDD Module

(1) Remove the 2 screws (M2*5) from Hard-Disk cover.

(2) Take the cover away.

BATTERY

HDD MODULE

REMOVAL

HDD MODULE

OPTICAL

DRIVE

REMOVAL

DISASSEMBLY PROCEDURE

2 - 3

(3) Remove the 2 screws (M2*5).

(4) Pull the Hard Disk out of the system.

Please do not touch inside of the HDD module.

Memory Module

The illustrations below show how to remove the Memory module from the notebook.

The M2400 NE (ID1) Series Notebook comes standard with 256MB of RAM onboard.

There is one expansion SODIMM socket for you to upgrade the total memory up to

768MB with a 512 MB module

Removing Memory module

(1) Remove the 3 screws (M2*5) from DIMM cover.

(2) Take the cover away.

(3) Remove SO-DIMM by opening the two latches to pop up it.

(4) Pull the SO-DIMM out.

MEMORY

REMOVAL

MEMORY

MODULE

DISASSEMBLY PROCEDURE

2 - 4

CPU Module

The illustrations below show how to remove the CPU module from the notebook.

(1) Remove the 2 screws (M2*5) from FAN and gently lift the CPU fan.

(2) Disconnect the CPU FAN cable and remove the 4 screws (M2*5) from

Heat-Sink.

CPU MODULE

REMOVAL

DISASSEMBLY PROCEDURE

2 - 5

(3) Then lift the CPU heat-sink module and carefully remove the CPU

thermal pad.

(3) Turn the non-removable screw here 180 degrees counter-clockwise to

loose the CPU and squeeze the vacuum handling pump and use it to lift

the CPU away.

Keyboard Module

The illustration below shows how to remove the K/B plate.

K/B MODULE

DISASSEMBLY PROCEDURE

2 - 6

Removing K/B

(1) Press the delete key and lift the right side of keyboard cover.

(2) Slide the cover along right side.

(3) Disconnect the cable, and take the keyboard cover away.

(4) Disconnect the cable from keyboard cover.

(5) Remove 2 screws (M2*5).

(6) Slide forward the keyboard and pull the keyboard up.

K/B

REMOVAL

DISASSEMBLY PROCEDURE

2 - 7

Removing Keyboard Cable

1. Use a flexible connector tool to unlock the cable connector on both ends (no. 1).

2. Carefully pull out the keyboard cable (no. 2) with a pair or tweezers.

3. Lock the connector (no. 3) again to avoid possible breakage.

4. Finally the keyboard plate can be removed from the notebook.

Mini - PCI Module

The illustrations below show how to remove and disassemble the Mini-PCI module.

Removing Mini - PCI Module

(1) Remove it by opening the latches, which will pop the module up to a 45°

angles, and then pulling out the module in that angle

(2) Remove the Antenna cable from Mini-PCI module.

CABLE

REMOVAL

1. Unlock

2. Cable out

1. Unlock

MINI-PCI

REMOVAL

DISASSEMBLY PROCEDURE

2 - 8

LCD Module

The illustrations below show how to remove and disassemble the LCD module. The

module contains LCD panel, inverter board, LCD hinge bracket, hinge cover, antenna,

LCD front cover and LCD bottom case.

Disassembling LCD Module

(1) Remove the 2 screws (M2.5*6) of hinge from the bottom side.

(2) Remove the LCD hinge covers.

(3) Remove the LCD harness cover, be careful the Antenna.

(4) Remove the 2 screws (M2.5*6) from the hinge feet on both sides.

LCD

DISASSEMBLY

DISASSEMBLY PROCEDURE

2 - 9

(5) Disconnect the LCD coaxial cable and Inverter Board cable

(6) Disconnect the Microphone cable and lift straight up the LCD panel from

the system.

(7) Remove 5 rubber pads and 5 screws (M2.5*6)*3 and (M2*5)*2.

DISASSEMBLY PROCEDURE

2 - 10

(8) Carefully pry the inside edges of LCD front cover and take it away.

(9) Remove LCD cable from inverter board.

(10) Remove 2 screws (M2*3) from both sides.

(11) Take the LCD panel away.

(12) Disconnect the LCD coaxial cable.

(13) Remove the microphone line.

(14) take the inverter board module away.

Tabla de contenidos

Manuales populares de Computadora portátil de otras marcas

HP ze2401xt - Pavilion Notebook PC Manual de usuario

Velocity

Velocity NoteMagix M10 Manual de usuario

Dell

Dell Alienware 17 R2 Manual de usuario

Toshiba

Toshiba A105-S2236 Manual de usuario

HP ENVY 17 Manual

Winbook

Winbook LM Manual de usuario

Dell

Dell Inspiron 1464 Manual de usuario

Dell

Dell Inspiron 15R 5537 Manual de usuario

HP PROBOOK 4520S Manual

Dell

Dell Latitude ATG D620 Manual de usuario

Sony

Sony VAIO PCG-FX270 Manual de usuario

Dell

Dell Latitude 7310 Manual de usuario

Dell

Dell Precision GU806 Manual de usuario

Sony

Sony VAIO PCG-R505JLK Manual de usuario

Lenovo

Lenovo THINKPAD X32 Manual de usuario

HP Compaq tc4200 Guía de inicio rápido

Toshiba

Toshiba mini NB300 Manual de usuario

Lenovo

Lenovo ThinkPad X201 Tablet Manual