Asus KN1 Series Manual de usuario

Tabla de contenidos

Otros manuales de Computadora portátil de Asus

Manuales populares de Computadora portátil de otras marcas

HP

HP ze2401xt - Pavilion Notebook PC Manual de usuario

Velocity

Velocity NoteMagix M10 Manual de usuario

Dell

Dell Alienware 17 R2 Manual de usuario

Toshiba

Toshiba A105-S2236 Manual de usuario

HP

HP ENVY 17 Manual

Winbook

Winbook LM Manual de usuario

Dell

Dell Inspiron 1464 Manual de usuario

Dell

Dell Inspiron 15R 5537 Manual de usuario

HP

HP PROBOOK 4520S Manual

Dell

Dell Latitude ATG D620 Manual de usuario

Sony

Sony VAIO PCG-FX270 Manual de usuario

Dell

Dell Latitude 7310 Manual de usuario

Dell

Dell Precision GU806 Manual de usuario

Sony

Sony VAIO PCG-R505JLK Manual de usuario

Lenovo

Lenovo THINKPAD X32 Manual de usuario

HP

HP Compaq tc4200 Guía de inicio rápido

Toshiba

Toshiba mini NB300 Manual de usuario

Lenovo

Lenovo ThinkPad X201 Tablet Manual

DISASSEMBLY PROCEDURE Chapter

2

Disassembly Procedure

Please follow the information provided in this section to perform

the complete disassembly procedure of the notebook. Be sure

to use proper tools described before.

K

N1Series Notebook consists of various modules. This chapter describes

the procedures for the complete notebook disassembly. In addition, in

between procedures, the detailed disassembly procedure of individual

modules will be provided for your service needs.

The disassembly procedure consists of the following steps:

•Battery module

•Keyboard Module

•ODD module

•HDD module

•CPU Module

•VGA Card Module

•Memory Module

•W/L Card Module

•LCD Module

•Top cover Module

•Motherboard Module

2 - 1

DISASSEMBLY PROCEDURE

Battery module

BATTERY

The illustration below shows how to remove the battery module.

1. Turn the notebook over. Unlock one latch (no.1) and remove the battery pack

from bottom side (no.2).

1

2

1

. Keyboard Module

K/B MODULE

The illustration below shows how to remove the K/B cover and keyboard plate

Removing K/B cover

K/B COVER

REMOVAL .1.Release two screws (no. 1, 2;) from K/B cover on left and right side

1 2

2 - 2

DISASSEMBLY PROCEDURE

2 - 3

2. Turn the notebook over, release one screws

K/B COVER

REMOVAL

3. Open K/B cover from rear side, then separate it from left side

K/B COVER

REMOVAL

Removing K/B

1. Release K/B 2pcs screw

K/B REMOVAL

DISASSEMBLY PROCEDURE

2. Disconnect K/B cable

K/B REMOVAL

1. Unlock

3.

Lock

2. Cable out

1. Unlock

3.

Lock

ROM DRIVER

REMOVAL

1 . Removing ROM drive

1. Release 1pcs screw

2 - 4

DISASSEMBLY PROCEDURE

2.Pull out the ODD device from top side

ROM DRIVER

REMOVAL

HDD Module

HDD MODULE

The illustrations below show how to remove the HDD module from the notebook.

Removing HDD Module

HDD MODULE

REMOVAL

1. Release 2 screws from bottom of notebook.

2. Pull out the HDD module from front side of notebook.

1

2

Disassembling HDD Module

HDD MODULE

REMOVAL

1. Release 4pcs screws on both side of the HDD module.

2 - 5

DISASSEMBLY PROCEDURE

Please do not touch inside of the HDD module.

CPU Module

The illustrations below show how to remove the CPU module from the notebook.

The module contains CPU, CPU thermal pad, and CPU thermal module.

Removing CPU

1.Release 6pcs screw on thermal door

2.Remove the thermal door

CPU

CPU REMOVAL

1

1

1

2

CPU REMOVAL

3. Release 4pcs screw and cable conn

4. Then pull out CPU thermal module

2 - 6

DISASSEMBLY PROCEDURE

3

4

CPU REMOVAL

5. Remover CPU

VGA CARD REMOVE

VGACARD

REMOVAL 1. Release 4pcs screw on theVGA thermal, then remove VGA thermal

2. Release1pcs screw on theVGA card , then pull out VGA card

2 - 7

DISASSEMBLY PROCEDURE

1

2

Memory Module

MEMORY

REMOVAL The illustrations below show how to remove the Memory module from the notebook.

The KN1 Series Notebook comes standard without memory onboard. There

are two expansion SODIMM sockets for you to upgrade the total memory up to

2GB with two 1024 MB modules

Removing Memory module

If there is an existing memory, remove it by opening the latches, which will pop

the module up to a 45°angle, and then pulling out the module in that angle

MEMORY

REMOVAL

2 - 8

DISASSEMBLY PROCEDURE

2 - 9

W/L CARD

REMOVAL W/L CARD REMOVE

1. Release 1pcs screw, then remove wireless door

2. Remove antenna , pull out wireless card

W/L CARD

REMOVAL

DISASSEMBLY PROCEDURE

LCD module

LCD

The illustrations below show how to remove and disassemble the LCD module.

The module contains LCD panel, inverter board, LCD hinge bracket, hinge

cover, LCD bezel and LCD cover.

Removing LCD Module

LCD REMOVAL

1.Disassemble the antenna on base side

2. Pull out LCD cable conn

LCD REMOVAL

3. Disassemble antenna and LCD cable conn

3

2

2 - 10