Astral Pool CONTROL BASIC PLUS Manual de usuario

Code 0000138008 rev 1.0

CONTROL BASIC PLUS ASTRALPOOL

INSTRUCTIONS MANUAL

HANDBUCH

MANUAL DE INSTALACION

MANUEL D’INSTALLATION

MANUALE D’INSTALLAZIONE

MANUAL DE INSTALAÇÃO

Code 0000138008 rev 1.0

Code 0000138008 rev. 1.0

CONTROL BASIC PLUS ASTRALPOOL

PACK CONTENTS

A) "Basic ASTRALPOOL" pH / REDOX control device

B) PVC Crystal 4x6 with suction device (2 m)

C) Polyethylene delivery hose (3m)

D) Attachment screw (f=6 mm)

E) Foot filter (PVC riser)

F) FPM duckbill valve (3/8” GAS)

G) ModBus connector

Wall Mounting Setup

TECHNICAL SPECIFICATIONS

Dimensions (H – W – L) 234x162x108 mm

Weight 1 kg

Power supply 50 Hz 230 VAC

Consumption 12 W or 18 W

Pump flow rate 1,5 l/h; 5 l/h

Maximum back-pressure 1,5 bar

Pump state Pause - Supply

Measure scale 0 ÷ 14.0 pH; Redox 0÷ +1000 mV

Device precision ± 0,1 pH; ± 10 mV

Device accuracy ± 0,02 pH; ± 2 mV

Electrode regulation Automatic

ATTENZIONE / WARNING / ATTENTION / ACHTUNG

Code 0000138008 rev. 1.0

Instruction Setting

Functions:

• Calibration

o (Press for 3 Seconds):

o Standard Routine calibration for 7 and 4 buffer solution

• Set Point

o Press

§ Keep Press Set Key and adjust value with

§ Sp_7.4ph

• Press for 5 Seconds and run Program Setup:

o Program

§ Press to set the following Item

• PUMP Config.

§ Adjust pH or Redox

• Language

§ (It’s possible to have 5 language EN, IT, SP, DE, FR

§ dosage type

§ Adjust value with and

• It’s possible to adjust value between PROP or ON/OFF

• Flow

§ Adjust value with and

• It’s possible to enable(ON) or disable (OFF) signal input

• rs485 settings

Press to set the following Item

§ rs-485

• Adjust value with and

Code 0000138008 rev. 1.0

• It’s possible to enable(ON) or disable (OFF) the communication.

§ wdg config.

• Adjust value with and

• It’s possible to set as: Hardware Reset, Com. Reset, Stop Dosage and

WDG Alarm (default value).

§ rs485 watchdog

• Adjust value with and

• It’s possible to adjust the time in seconds. If it is set as OFF (default value)

the communication watchdog is disabled.

§ address

• Adjust value with and

• It’s possible to adjust the address of the device from 1 (default value) to 247

§ parity

• Adjust value with and

• The value of the parity bit, it’s possible to set as: Even (default value), Odd

or No.

§ baudrate

• Adjust value with and

• The value of the speed of the transmission, it’s possible to set as: 2400,

4800, 9600 (default value), 19200.

•

o Setpoint 7.4ph

o Adjust value with and

§ It’s possible to adjust from 0 to 14 pH value and 0 to 1000 mV for Redox

o Setpoint Type Acid

§ Adjust value and

§ It’s possible to adjust Acid or Alkaline dosing and High or Low for Redox

o OFA Time off

§ Adjust value and

§ It’s possible to adjust OFA time in minutes

Code 0000138008 rev. 1.0

o Calibration 7/4pH

§ Adjust value and

§ It’s possible to select 2 points 7 and 4 pH, 1 point only 7pH or function disable; for

Redox function disable only.

o Man Temperature 25

§ Adjust value and

§ pH measure only.

• Save and escape Program setup with ESC key

o Exit save

§ Adjust value with up or down key and confirm with

o Priming

• Priming Pump Keep Press for 3 seconds

Wire Connection:

1) Input pH or Redox Probe

2) Input Temperature Probe (PT100)

3) Input Level Probe (Product Tank)

4) Input Flow Rate (High Voltage 230 Vac)

5) Output Relay Alarm remote (Dry contact,

Relay 250 Vac 10 A)

6) Output Relay Drive Solenoid Valve (Dry

contact, Relay 250 Vac 10 A)

7) Power Supply 230 Vac

8) Switch Power Supply

9) Connection to a chlorine generator (example)

10) Port connection for the ModBus communication

ModBus connetion

Pin N°

Description

T+R+ (B)

T-R- (A)

GND

Not used

CHLORINE

GENERATOR

250 V/50 A

REMOTE CONTROL

SWITCH

(NOT INCLUDED)

230 Vac

Code 0000138008 rev. 1.0

pH Probe Calibration

Wash

Keep probe into Buffer solution

Calibration

Press Cal Key 3 Seconds

7pH___Press_CAL

Calibration During 1 minutes

Wait________60s

7pH_Quality_100%

Quality Probe

Wash

Keep probe into Buffer solution

4pH___Press_CAL

Calibration During 1 minutes

Wait________60s

4pH_Quality_100%

Quality Probe

Wash

Press Enter Key to save and exit

Normal Status

Note:

If you have setting Calibrabration = 7 pH the function has 1 point calibrate only 7 pH buffer solution.

Code 0000138008 rev. 1.0

Redox Probe Calibration

Wash

Keep probe into Buffer solution

Calibration

Press Cal Key 3 Seconds

465mv___Press_CAL

Calibration During 1 minutes

Wait________60s

465mv_Quality_100%

Quality Probe

Press Cal Key 3 Secondù

Normal Status

Code 0000138008 rev. 1.0

Alarm

Display

Relay

Actions to do

Level

Level____7,2_ph

Alarm Relay

- Push Enter Key to open

Alarm Relay

- Restore Product tank

OFA First Alarm (time >70%)

OFA_Alarm__7,2_ph

Alarm Relay

open

- Push Enter Key to reset

OFA Second Alarm (time =100%)

OFA_STOP___7,2_ph

Alarm Relay

- Push Enter Key to reset

Flow Rate

Flow_______7,2_ph

Alarm Relay

open

- Restore Flow Rate

System Error

Parameter_Error

Alarm Relay

Open

- Press Enter Key to replace

Default parameter

Communication Watchdog alarm

Wdg_Alarm

Alarm Relay

- Check the communication

network

Calibration Function

Error_7_ph

Error_4_ph

Error_465_mV

Alarm Relay

open

- Restore Probe or Buffer

solution and repeat calibration

function

To restore Default parameters run Following steps:

•Power off Pool Basic unit

•Keeping Press UP and DOWN Key switch on the

Power.

•The unit will flash Init.default__no

•Press up Init.default__Yes

•Enter Key to restore Default parameters.

Default parameters:

•Language = UK

•Set Point value= 7,4 pH; 750mV (Rx)

•Dosing Method = Acid; Low (Rx)

•Time OFA = OFF

•Calibration = 7/4 (2 point); 465mV (Rx)

•Flow Input = OFF

Code 0000138008 rev.1.0

CONTROL BASIC PLUS ASTRALPOOL

Verpackungsinhalt

A) "Basic ASTRALPOOL" pH / REDOX Kontrollsystem

B) PVC-Schlauch Crystal 4x6 (2 m)

C) Polyethylen-Schlauch (3 m)

D) Schrauben mit Dübeln (f = 6 mm)

E) Fußfilter (PVC)

F) Rückschlagventil aus FPM (3/8” GAS)

G) ModBus-Anschluss

Wandmontage

TECHNISCHE DATEN

Abmessungen (H - B - T) 234x162x108 mm

Gewicht 1 kg

Spannungsversorgung 230 Vac

Verbrauch 12 W oder 18 W

Förderleistung der Pumpe 1,5 l/Std.; 5 l/Std.

Max. Gegendruck 1,5 bar

Pumpenstatus Pause - Betrieb

Messskala 0 ÷ 14.0 pH; Redox 0 ÷ +1000mV

Messgenauigkeit ± 0,1 pH; ±10 mV

Genauigkeit Maß ± 0,02 pH; ±2 mV

Kalibrierung der Elektrode automatisch

ATTENZIONE / WARNING / ATTENTION / ACHTUNG

Otros manuales para CONTROL BASIC PLUS

Tabla de contenidos

Idiomas:

Otros manuales de Unidad de control de Astral Pool

Astral Pool

Astral Pool POOL BASIC Manual de usuario

Astral Pool

Astral Pool 28512 Manual de instrucciones

Astral Pool

Astral Pool System VRAC Basic Manual

Astral Pool

Astral Pool HALO DOSER Manual de usuario

Astral Pool

Astral Pool 28512 Manual de usuario

Astral Pool

Astral Pool HALO XPAND Manual de usuario

Astral Pool

Astral Pool VRAC III Basic Series Manual

Astral Pool

Astral Pool CONTROL BASIC Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario