Assicontrol EASY-CHECK FE-S Manual de usuario

CONTENTS

INTRODUCTION Page 2

SHORT INSTRUCTIONS Page 3

FUNCTION MODES Page 4

OPERATION OF THE FUNCTIONS MODES Page 4

CALIBRATION Page 7

EXCHANGE OF THE BATTERY Page 7

CHARGE THE RECHARGEABLE BATTERY

WITH THE LINE-CHARGING UNIT Page 8

GENERAL REMARKS Page 8

TECHNICAL DATA Page 9

OPTIONAL ACCESSORIES Page 10

DATA PRINTER MEGA-PRINT Page 11

STRUMENTI &SERVIZI

per il sistema qualità

ia S. Silvestro, 92 21100 Varese

Tel + 39 0332 - 213045

212639- 220185

Fax +39 0332 - 822553

www.assicontrol.com

e-mail: [email protected]

C.F. e P.I. 02436670125

INTRODUCTION

Congratulation ! You really made a good choice to decide for

EASY-CHECK FE-S,

because this device is not only designed and manufactured according to

the latest level of technology, but also is extremely comfortable and easy

to operate.

We tried our best to write this manual as clear and short as possible. For

any further information you may need, please contact our Service De-

partment. Our technicians are always ready to help you.

What can you measure with EASY-CHECK FE-S ?

On iron and steel (FE) all non-magnetic coatings, such as varnish,

paint, plastics, enamel, rubber, ceramics and galvanization (except

niquel) up to 5 mm.

In addition EASY-CHECK FE-S includes the following features

•Store up to 1000 readings in the data memory

•Display statistics

•Transfer all readings and statistics to a printer or computer by means

of the interface, or just

•Transfer the data by RADIO.

All these functions can be performed with the red key.

And this is really unique:

•EASY-CHECK FE-S can measure up to 80 hours with only

one 1.5V Mignon battery.

•Worldwide the only device with a swinging measuring

probe allowing to measure inside pipes and in other in-

accessible places.

SHORT INSTRUCTIONS

To make it as easy as possible for you and to be able to

start taking measurements immediately, we have al-

ready calibrated the device.

You receive the instrument ready for operation and do

not need to perform any adjustments.

You just switch on the device with the red key. In the

display flashes shortly the number of the software ver-

sion and then appears <on>.

That´s all and now you can start taking measurements.

FUNCTION MODES

Switch on the device by pressing the key until <on> is displayed. Re-

lease the key.

When you now press the key once again for a longer time the

following modes will appear one after another:

Sto = Store readings in the Data Memory

StA = Display Statistics

Prn = Print or activate the Serial Interface

IcL = Clear the last reading

cLr = Clear the whole Data Memory

un = Change the unit of measurement (µm / mils)

rES = Switch over the resolution: 0.1 or 1.0 µm

By pressing the key the mode selected is confirmed.

OPERATION OF THE FUNCTION MODES

<Sto> Store readings in the Data Memory

To store readings in the memory for further evaluation press the key until

<Sto> is displayed.

Now release the key and press it again for confirmation and wait until

<on> is displayed.

The data memory is activated and all subsequent measurements will be

stored. The symbol <STORE> is displayed to make evident that the

memory is switched on.

Capacity of the data memory : 1000 readings

When the memory has reached its capacity limit the symbol <FUL> is

displayed.

As soon as the device is switched off the memory mode is deactivated.

<StA> Display Statistics

The readings stored in the data memory are evaluated as follows:

No. - Number of readings stored

MIN - Lowest reading stored

MAX - Highest reading stored

MEAN - Mean value

STD.DEV. - Standard deviation

Press the key until the symbol <StA> appears. Now release the key and

press it again to confirm. The statistics values are displayed one after

another.

<Prn> Print or Activate the RADIO CONTROL function

When EASY-CHECK FE-S is connected to the printer MEGA-PRINT or

operated with the RADIO CONTROL module, press the key until <prn>

is displayed. Then release the key and press it again to start the data

transfer.

This is not necessary when working with the interface cable and the

software selected. As soon as the interface cable is connected, the data

transfer starts by itself without pressing the key.

<IcL> Clear the last reading

Press the key until the symbol <IcL> is displayed. Release the key

shortly and press it again to confirm.

Now the last reading is cleared.

<cLr> Clear the whole Data Memory

Press the key until the symbol <cLr> is displayed. Release the key

shortly and press it again to confirm.

Now the whole Data Memory is cleared.

<Un> Change unit of measurement (µm / mils)

In its basic setting the instrument measures in µm.

To measure in “mils” (American unit of measurement) press the key until

the symbol <un>is displayed. Release the key and press it again to con-

firm.

When you switch on the instrument again it will measures in “mils”.

To change over to “µm” proceed in the same way.

<rES> Resolution

From factory the device is adjusted to the resolution 1.0 µm.

To switch over to the resolution 0.1 µm press the key until <rES> is

displayed. Release the key shortly and press it again to confirm the set-

ting.

CALIBRATION

You receive the device already calibrated. Nevertheless from time to

time it is necessary to check or correct the calibration. This is especially

recommended when you measure on small or curved objects or when

the surface of the test object is rough.

To calibrate the device you should always use the shim with the

higher value (approx. 300 µm). The shim with the lower value

(approx. 100 µm) is only supplied to verify the accuracy after

calibration.

•Switch on the device.

•Set the device with the probe on the base plate FE (blue) and press

the key for about 2 sec until <0.0> is displayed stable. Then release

the key and zero setting is performed and confirmed by a beep sig-

nal

•Take off the device, <cAl> is flashing.

•Press the key and the actual calibration value is displayed. This

value should be identical with your shim value (approx. 300 µm). If it

is not, you now can enter the correct value. Pressing the key shortly

the value goes down by 1, pressing it continuously the value scrolls

up.

•Once the correct calibration value is set, place the shim (approx.

300 µm) on the base plate FE (blue) and set the device on the shim

and wait until the beep sounds.

The device is calibrated.

To perform just a one-point calibration and after having set the zero

point, you can go on taking measurements while <cAl> is flashing. The

flashing <cAl> disappears on the display as soon as a new measure-

ment is taken.

When measuring on small or curved objects it is advisable to perform

calibration on a bare test object with the same geometry of the

object to be measured and not on the base plate supplied with the de-

vice.

EXCHANGE OF THE BATTERY

As soon as the symbol <BAT> is flashing the battery must be exchanged

by a new one.

When the voltage of the battery is less than 0.8 V the device switches off

by itself.

CHARGE THE 1.2V RECHARGEABLE BATTERY WITH THE

LINE-CHARGING UNIT

As soon as the symbol <BAT> is flashing the rechargeable 1.2V Mignon

battery must be charged.

Important: Before inserting the charging connector into the interface

plug of EASY-CHECK FE-S the device must be switched off.

The charger must not be connected when the 1.5V battery is inside

the device. The battery may run out and destroy the device !

With the device switched off the charging connector is inserted into the

interface plug of EASY-CHECK FE-S. The device switches on by itself

and a bar diagram with the battery symbol is displayed. With the charger

connected you can go on taking measurements.

After approx. 20 sec the state of charge is displayed again provided no

measurement is taken. When the charger is connected the automatic

switch off is deactivated.

The rechargeable battery needs approx. 8 hours to be charged com-

pletely. A constant bar diagram is flashing together with the battery sym-

bol and the charger can be removed.

GENERAL REMARKS

Thickness of the base material: at least 300 µm

Automatic switch-off

The device switches off automatically one minute after the last measu-

rement. The instrument can also be switched off with the red key.

IMPORTANT

The probe should not be drawn across the testing surface but reset at

different spots, i.e. after each measurement hold the instrument in the air

for about 1 sec. In doing so the stored calibration is automatically che-

cked and corrected if necessary.

Make sure that the probe surface and the base plate are kept clean

and polished at all times.

TECHNICAL DATA

Measuring Technique: Magnetic induction on iron and steel

(ISO 2178)

Measuring Range: 0 – 5000 µm

Indication: LCD 3½ digits with floating decimal point

and guides for operation

Resolution: selectable 1.0 µm or 0.1 µm

Accuracy: below 100 µm: ±1 µm

100 - 1000 µm: ±1 %

1000 - 2000 µm: ±3 %

> 2000 µm: ±5 %

Memory: max. 1000 readings

Statistics Indication of No.-MIN-MAX-MEAN-STD.DEV.

Power Supply: 1,5V Mignon battery

(1.2V rechargeable battery with charger

available)

Recording Data: one long beep

Measuring Probe: swinging by 90°

Dimensions: 108 x 48 x 38 mm

Weight:approx. 100 g

Interface: serial RS 232 C (5 V TTL level)

Baudrate: Printer + PC: 1200 baud

Data/Stop bits: Printer + PC: 7/2

Warranty: Indication unit: 12 months

Measuring probe: 3 months

OPTIONAL ACCESSORIES

SOFTWARE incl. Operation Instructions

•Software TRANSFER

Sends the data and statistics to the computer.

•Software TRANSFER-EXCEL

Transfers the data directly in an existing Excel file.

•Graphic Statistics Software STAT-6

Sends the data and statistics to the computer.

Limit values can be set which are evaluated as line and

bar diagrams.

RADIO- CONTROL

With the Transmitter / Receiver and the Software STAT-6 the

data and statistics can be sent to the computer by RADIO

without any cable connection.

Data Printer MEGA-PRINT

Print out all the data and statistics.

Line-Charger with 1.2V rechargeable Mignon battery

Tabla de contenidos

Otros manuales de Instrumento de medición de Assicontrol

Assicontrol

Assicontrol MACH-I Manual de usuario

Assicontrol

Assicontrol MP-2000 Manual de usuario

Assicontrol

Assicontrol TH-300 Manual de usuario

Assicontrol

Assicontrol TP-40 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario