Assa Abloy Yale Delayed Egress Manual de usuario

Exit Device

Delayed Egress

Attention Installer

Any retroﬁt or other ﬁeld modiﬁcation to a ﬁre rated opening

can potentially impact the ﬁre rating of the opening, and

Yale Locks & Hardware makes no representations or

warranties concerning what such impact may be in any

speciﬁc situation. When retroﬁtting any portion of an

existing ﬁre rated opening, or specifying and installing a new

ﬁre-rated opening, please consult with a code specialist or

local code ofﬁcial (Authority Having Jurisdiction) to ensure

compliance with all applicable codes and ratings.

Installation Instructions

For technical support contact Yale®at 800.438.1951 or support@yalelocks.com

80-9470-0162-000 10/18

An ASSA ABLOY Group brand

Available on the following devices:

Rim

Mortise

SquareBolt®

Concealed Vertical Rod

*Surface Vertical Rod

*Rod Guards Required (made by other manufacturers)

permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

For technical support contact Yale®at 800.438.1951 or support@yalelocks.com

An ASSA ABLOY Group brand 2

80-9470-0162-000 10/18

Delayed Egress

Installation Instructions

Exit Device

permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

TOC Table of Contents

Panic and Fire Rated Devices ...................................3

End Cover and P.C. Board Assembly...............................4

Installation of End Cover Assembly to Device ........................5

ElectroLynx Connector System for All Electrical Installation ..............6

Device Mounting ............................................7

Wiring Layout and Jumper Settings ...............................8

Non-ElectroLynx Door Prep.....................................9

Wiring Diagram - Single Door Exit Only ...........................10

Wiring Options ............................................11

Operating Instructions .......................................12

Additional Options..........................................13

Troubleshooting ...........................................14

For technical support contact Yale®at 800.438.1951 or support@yalelocks.com

An ASSA ABLOY Group brand 3

80-9470-0162-000 10/18

Delayed Egress

Exit Device

Installation Instructions

permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

1 Panic and Fire Rated Devices

1. Check device for shipping damage prior to installation and make sure all parts are on hand.

2. Identify options provided with device.

3. Identify model, type and hand of trim if applicable (see exit device and trim instructions for reversing

hands).

4. Contact your hardware supplier if your device is damaged or missing any parts.

A. Checklist

B. Required Components (Numbered list correlates with numbers in Figure 1)

C. Optional Components (Numbered list correlates with numbers in Figure 1)

1. Delayed Egress Exit Device

2. 24VDC UL Listed Regulated and ﬁltered Power Supply with Fire Alarm Interface. (Recommend

Securitron BPS 24-1 or 24-2 (UL294 Listed), depending on your requirements). Power supply is

NOT to be used in UL603 Burglar Alarm System.

3. Power transfer UL or Ulc listed (2-10 wire depending on system)-Securitron (EPT) or equivalent.

4. Sign (MUST BE INSTALLED ON DOOR ABOVE DEVICE).

NOTE: The delayed egress system is to be installed in accordance with NFPA 101.

5. Remote Annunciator

6. Door Position Switch (DPS)

7. Standard Trim

8. Electriﬁed Trim

9. Device and Trim Cylinder

D. Electrical Speciﬁcations*

Input Voltage 24VDC (+/-10%)

Wire Size:

18 AWG Min (up to 100')

Signal or Control 22AWG Min

Power Consumption:

Standard Device - 500mA

Device with Security Package - 750 mA

Device with Electric Trim - 1.25 amps

*Follow Local Electrical Codes for Wiring.

NOTE: Components shown do not reﬂect all possible applications. Consult manufacturer for

special applications.

PUSH UNTIL ALARM

SOUNDS. DOOR CAN BE

OPENED IN 15 SECONDS.

115 VAC

800 mA

60 Hz

Fire

Alarm

Circuit

Req’d

Figure 1

For technical support contact Yale®at 800.438.1951 or support@yalelocks.com

An ASSA ABLOY Group brand 4

80-9470-0162-000 10/18

Delayed Egress

Installation Instructions

Exit Device

permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

2 End Cover and P.C. Board Assembly

1. Trim device to proper length as required.

36" Exit Device - 1" maximum can be

trimmed

48" Exit Device - 6" maximum can be

trimmed

2. Carefully slide circuit board assembly into end

Cover to ensure indicator light (LED) is not

bent.

3. Insert mortise cylinder into end cover with

keyway horizontal, as shown.

4. Slide arming switch activator over mortise

cylinder so activator legs are on each side of

switch.

Figure 2

5. Insert ﬂange of cylinder nut into arming

switch activator to allow rotation of

activator.

6. Tighten cylinder nut on mortise cylinder and

to secure circuit board assembly.

7. Verify assembly by rotating key counter

clockwise and clockwise. Key should move

freely and arming switch should trip for

both rotation directions. If key does not

rotate freely, verify cylinder nut was placed

in correct orientation. If arming switch does

not trip, activator legs on arming switch

activator can be bent to reduce or increase

rotational travel.

Rear Cover End Cap

1-1/8" (29)

Mortise Cylinder

with Ya le 2160 Ca

(Order Separately)

1765 Series

Cylinder Collar

(Order separately

when required)

End Cover

Circuit Board Assembly

Indicator Light ()LED

Lens Cover

Arming Switch Activator

Tabs

NOTE:Factory keyed orders will

be shipped assembled.

Cylinder Nut

Activator Legs

1765 Series

Cylinder Collar

1-1/8"

(29)

1-1/2"

(38)

2160 Cam

Dia

.742"

(18.9

mm)

Order Separately

NOTE: • Use Ya le®2153 x 2160 cam,

1-1/8" mortise cylinder

• For cylinders over 1-1/8",

use Yale® 1765 Series cylinder ring.

Typical Mortise Cylinder

For technical support contact Yale®at 800.438.1951 or support@yalelocks.com

An ASSA ABLOY Group brand 5

80-9470-0162-000 10/18

Delayed Egress

Exit Device

Installation Instructions

permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

3 Installation of End Cover Assembly to Device

1. (J5) Nuisance Delay (Figure 3)

Jumper on - 3 seconds (Default)

Jumper off - immediate alarm

2. (J8) Reset Delay (Figure 3)

Jumper on - 10 seconds (Default)

Jumper off - 20 seconds

3. Slide end cover assembly into exit device.

(Figure 3) Do NOT pinch or crimp wires!

Figure 3

4. Connect device lock assembly to Connector

J1. (Figure 4)

5. Place wire connectors and excess wire

between end cover and circuit board.

(Figure 4) Check all connections before

proceeding.

J5 J8 Connector J2

To Power Transfer Hinge

Connector J1

Plugs into Device Lock Assembly

End Cover Assembly

Optional Wires

To Power Transfer

Lock Assembly Harness

Exit Device

Connector J2

To PowerTransfer Hinge

Optional "O", "S" or

Saf

e/Secure wire

(Ref

er to wiring diagram

for wiring)

Place Connector

and ExcessWire

in this Area

J1 Connector

Plugs into Device Lock Assembly

Figure 4

For technical support contact Yale®at 800.438.1951 or support@yalelocks.com

An ASSA ABLOY Group brand 6

80-9470-0162-000 10/18

Delayed Egress

Installation Instructions

Exit Device

permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

4 ElectroLynx Connector System for All Electrical Installation

1. Mount exit device per instruction sheet provided.

2. Plug exit device connector into raceway connector in door and feed through 1" (25mm) hole in door.

Install rail mounting end clamp bracket with two (2) screws supplied. Install end cap.

3. Plug raceway connector from edge of door into electric hinge connector and feed feed wires back

through door prep. Mount electric hinge to door.

A. If wiring now, wire frame side wires to wires on pigtail harness on hinge as required by using

connectors allowed by local code. Plug pigtail harness connector into electric hinge connector.

Feed harness through frame prep and mount electric hinge.

B. If wiring later, plug pigtail harness connector into electric hinge connector. Feed harness through

frame prep and mount electric hinge.

NOTE:

1. Wiring to pigtail harness is per facility wiring requirement.

2. For an ElectroLynx system, go to “function” or “monitor” page(s) with your device.

3. Combinations of certain monitors can be used in each device. These instructions detail installation

of each monitor separately.

ElectroLynx Connector System Notes:

System is designed to be installation friendly, with plug connectors from electric hinge through door

to device. The only wiring required is loose wires on pigtail harness assembly on frame side of electric

hinge (included with QC Hinge). Combinations of certain switches and monitors can be used.

The plug and receptacle connectors are designed to mate and lock together. Plug connectors into each

other with locking mechanism aligned. Do NOT force connectors together any other way.

For technical support contact Yale®at 800.438.1951 or support@yalelocks.com

An ASSA ABLOY Group brand 7

80-9470-0162-000 10/18

Delayed Egress

Exit Device

Installation Instructions

permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

5 Device Mounting

Figure 5

1. For ElectroLynx Hinge Connector System:

Follow Section 4 wiring instructions.

2. For non-ElectroLynx door: Remove connector

at end of exit device and connect to incoming

wires from power source using wire nuts, butt

splices, etc.

NOTE:

• Switch contact rating: 5A @28VDC.

• Wire must be protected from abrasion.

• For use with Class II circuits only.

LHR Installation with O Monitor Shown

End Clamp

PowerTransfer

Hinge

Wire Access

3/4" Dia. hole on sam

centerline as device.

Inside face only.

End Cover

Installed

4()TA NNC

3()PNK NO

2(C)GRY

OMonitor

Connections

Pigtail harness

with 4-pin connector

Pigtail harness

with 8-pin connector

2(+)RED

8(Remote )YEL BYP

6(Secure )BLU NO

7(Remote)BRN RES

3(Alarm)WHT NC

5(Secure )ORG NC

1 (-)BLK

4(Alarm)GRN NO

Function

Connections

Figure 6

Security Package H Strike Magnet Installation

1. Mount strike to frame.

2. Line up magnet to strike.

3. Mark screw hole.

4. For security package, prep hole for one (1)

10-24 machine screw.

NOTE: LHR device magnet position shown. RHR

device will be located on bottom of strike.

Door Position

Switch

Device

Magnet

Strike

For technical support contact Yale®at 800.438.1951 or support@yalelocks.com

An ASSA ABLOY Group brand 8

80-9470-0162-000 10/18

Delayed Egress

Installation Instructions

Exit Device

permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

6 Wiring Layout and Jumper Settings

Pin Number Input/Output Wire Color Description Pin Number

1 Input Black 24VDC Power Supply (-Circuit Ground) 1

2 Input Red 24VDC Power Supply (+Positive) 2

3 Input Brown

Remote Reset Input - Momentary input from

key switch, pushbutton, etc. Will release device

for 20 seconds for egress or ingress and also

reset device when in bypass or alarmed state.

4 Input Yellow

Remote Bypass Input - Momentary input from

key switch, pushbutton, etc. Will maintain device

in an unlocked state for normal device operation.

Device must be rearmed by resetting from

remote reset on device.

5Output Orange

Secure Relay Output - Normally closed (NC)

contact that changes to normally open (NO)

when device has released.

6 Output Blue

Secure Relay Output - Normally open (NO)

contact that changes to normally closed (NC)

when device has released.

7Output Green

Alarm Relay Output - Normally open (NO)

contact that changes to normally closed (NC)

when device alarm cycle has been activated.

8Output White

Alarm Relay Output - Normally closed (NC)

contact that changes to normally open (NO)

when device alarm cycle has been activated.

Connector

ElectroLynx

Connector

NOTE: • Pins 5-8 are negative (-) outputs. Use with LEDs and audibles (horns, sirens, etc.).

See wiring diagrams for details.

• Cap all unused wires with enclosed wire nuts.

Figure 7

1. (J5) Nuisance Delay (Figure 7)

Jumper on - 3 seconds (Default)

Jumper off - immediate alarm

2. (J8) Reset Delay (Figure 7)

Jumper on - 10 seconds (Default)

Jumper off - 20 seconds

Activating Legs

Arming Switch

Circuit Board

End Cover

J2: To PowerTransfer

J1: To Device Connections

J5 J8

For technical support contact Yale®at 800.438.1951 or support@yalelocks.com

An ASSA ABLOY Group brand 9

80-9470-0162-000 10/18

Delayed Egress

Exit Device

Installation Instructions

permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

7 Non-ElectroLynx Door Prep

Figure 8

NOTE:

1. Do not scale drawing.

2. Dimensions are in inches (mm).

3. LHR H.M. opening shown. Details are

typical for all opening materials (both

hands).

4. This preparation is an addition to

preparation shown on device template.

5. See device template to locate

centerline of device template.

6. Shields for wring access

recommended for insulated and

composite doors.

7. Locate and prepare wiring access

holes when installing device.

Exit Device

7100 Series

7200 Series

Dim. A

2-5/16 (59)

1-11/16 (43)

For technical support contact Yale®at 800.438.1951 or support@yalelocks.com

An ASSA ABLOY Group brand 10

80-9470-0162-000 10/18

Delayed Egress

Installation Instructions

Exit Device

permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

8 Wiring Diagram - Single Door Exit Only

Operation Monitoring

Red LED indicates device is armed and secure.

Activating device will sound horn. Green LED will

illuminate after 15 seconds. Device will release for

exit (unsecure).

Figure 9

CNC

FIRE ALARM

Delayed

Egress

Device

GND (-)

24V(+)

ALRN/C WHT

ALRN/O GRN

SECN/O BLU

SECN/C ORN

BYPASS YEL

RESETBRN

24V(+) RED

GND (-)BLK

Connector2

GND (-)BLK

DPS BLU

POWER(+) RED

NC NC

LOCK WHT RED/

LOCK WHT

TRIGGER SW YELWHT/

TRIGGER SW YEL

Connector1 ConnectorJ1

Wire Transfer

Hinge

SECURITRONBPS

POWERSUPPLY

24V(+)

GND(-)

NEUTRAL

EARTH

ALARM

120 VAC

Tabla de contenidos

Otros manuales de Cerradura de puerta de Assa Abloy

Assa Abloy

Assa Abloy ES8100 Instrucciones de montaje

Assa Abloy

Assa Abloy ZI IKON eCLIQ N109 Manual de usuario

Assa Abloy

Assa Abloy Yale Assure Lock YRC226 Especificaciones técnicas

Assa Abloy

Assa Abloy PE920 Manual de usuario

Assa Abloy

Assa Abloy EL580 Manual de usuario

Assa Abloy

Assa Abloy Pyramid Manual de usuario

Assa Abloy

Assa Abloy effeff 843ZY-1 Q41 Series Manual de usuario

Assa Abloy

Assa Abloy Yale Essential Series Manual de usuario

Assa Abloy

Assa Abloy Lockwood Onyx 9A1A2/5PBLK Manual de usuario

Assa Abloy

Assa Abloy Yale nexTouch Especificaciones técnicas

Assa Abloy

Assa Abloy IKON VERSO CLIQ Manual de usuario

Assa Abloy

Assa Abloy Yale Pro SL Especificaciones técnicas

Assa Abloy

Assa Abloy ABLOY EL587 Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin ED5200N Series Manual de usuario

Assa Abloy

Assa Abloy Yale Assure Lock YRC256-ZW3 Especificaciones técnicas

Assa Abloy

Assa Abloy Corbin Russwin HP3000 Series Manual de usuario

Assa Abloy

Assa Abloy 8800 Series Manual de usuario

Assa Abloy

Assa Abloy effeff ANYKEY Manual de usuario

Assa Abloy

Assa Abloy HES 9400 Instrucciones de funcionamiento

Assa Abloy

Assa Abloy 179B S4 Guía del usuario

Assa Abloy

Assa Abloy Corbin Russwin Access 800 TCAC2 Series Manual de instalación

Assa Abloy

Assa Abloy Yale YMI70A Manual de usuario

Assa Abloy

Assa Abloy 179C Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin CLX3300 Series Manual de usuario

Manuales populares de Cerradura de puerta de otras marcas

We.lock

We.lock SECBNEBL51 Manual de usuario

Iseo

Iseo MA1A Manual de usuario

ID Lock

ID Lock 150 Manual de usuario

Lockly

Lockly ACCESS TOUCH PRO Manual de usuario

iLoq

iLoq G50S Manual de usuario

SDC

SDC Z7835 Manual de usuario

ilco

ilco 452 Manual de usuario

Samsung

Samsung shs-h705 Manual de usuario

TRU-BOLT

TRU-BOLT 08102017 Manual de usuario

CDVI

CDVI 500-LADJ Manual de usuario

Igloohome

Igloohome Deadbolt 2S Metal Grey Instrucciones de instalación y mantenimiento

eSSL

eSSL FL-300 Manual de usuario

JAKO

JAKO JKBTNX4 Manual de usuario

Dorma

Dorma MUNDUS PREMIUM GK 50 Guía del usuario

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manual de usuario

Yale

Yale MORTISE 8800 SERIES Manual de usuario

Siegenia

Siegenia KFV AS3500 Manual de usuario

Saflok

Saflok Quantum ädesē RFID Manual de usuario