Assa Abloy ADAMS RITE 4300 Series Manual de usuario

1 80-0180-418, Rev D

4600 Heavy Duty Designer Deadlatch Handles With

4300, 4500, and 4900 Series Deadlatches

Installation Instructions

TABLE OF CONTENTS

Tools and Equipment Needed ........................................................................................................ 2

Preparing the Stile........................................................................................................................... 2

Offsetting the Escutcheon for 31/32” [24.61 mm] and 1-1/8” [28.58 mm] Backset........................ 4

Optional Monitoring Switch ............................................................................................................. 4

Installing Trim to Stile...................................................................................................................... 5

Installing the Handle........................................................................................................................ 6

Determining and Changing the Handing Configuration.................................................................. 7

Changing the Handing of the 4581 Cam Disc................................................................................. 7

Phoenix, AZ

Tel: 1-800-872-3267

Mon-Fri: 6:00am - 4:00pm PDT

Fax: 1-800-232-7329

www.adamsrite.com

2 80-0180-418, Rev D

IMPORTANT: This product must be installed according to all applicable building and

life safety codes!

Tools and Equipment Needed

The following common hand tools are needed for installation:

• 7/32” [5.56 mm], 1/4” [6.35 mm], and 3/8” [9.53 mm] drill bits

• 3/32” [2.38 mm] Allen Wrench

• Center punch

• Drill

• Flat tip screwdriver

• Phillips screwdriver

• Pencil

Preparing the Stile

NOTE: Figure 1, “Rivnut Installation for 31/32” [24.61 mm] and 1-1/8” [28.58 mm] Backset,

Single Lever,” and Figure 2, “Rivnut Installation for 1-1/2” [38.1 mm] Backset, Single

Lever,” provide illustration for the following steps.

1. IF using a 1-1/8” [28.58 mm] backset,

THEN MARK a vertical reference line 5/32” [3.97 mm] behind the backset centerline.

2. APPLY the stick-on template over the cylinder backset centerline reference 5/32” [3.97 mm]

offset to clear the stop on the frame for a 1-1/8” [28.58 mm] backset.

3. CENTERPUNCH all holes.

4. DRILL holes at center punch locations.

5. REMOVE the template.

3 80-0180-418, Rev D

Figure 1. Rivnut Installation for 31/32” [24.61 mm] and 1-1/8” [28.58 mm] Backset, Single Lever

Figure 2. Rivnut Installation for 1-1/2” [38.1 mm] Backset, Single Lever

Inches [Millimeters]

4 80-0180-418, Rev D

Offsetting the Escutcheon for 31/32” [24.61 mm] and

1-1/8” [28.58 mm] Backset

1. LOOSEN the two #4-40 x 1/4” flat head screws securing the adjustable cover on the back of

the trim cartridge until the cover can be slid (see Figure 3, “Adjustable Cover and Trim

Cartridge”).

2. PUSH the adjustable cover toward the nose edge of the door until it stops (see Figure 3).

3. TIGHTEN the two #4-40 flat head screws to secure the adjustable cover in place.

Figure 3. Adjustable Cover and Trim Cartridge

Optional Monitoring Switch

NOTE 1:Monitored trim contains an internally mounted switch (see Figure 4, “Optional Monitor

Switch”), secured with two M1.6 x .35 mm Phillips pan head screws. The switch is

activated when the handle is rotated to the UNLOCK position.

NOTE 2: All unused leads from the monitor switch must be terminated.

Figure 4. Optional Monitor Switch

5 80-0180-418, Rev D

1. WIRE the optional monitor switch in accordance with Table 1, “Wire Colors and Maximum

Switching Current,” and Figure 5, “Example Wiring Diagram with N.O. Monitoring.”

Table 1. Wire Colors and Maximum Switching Current

Wire Color Label

Black Common Contact

White Normally Open Contact (N.O.)

Red Normally Closed Contact (N.C.)

Maximum Switching Current

(choose N.O. or N.C. for monitoring) 0.1A at 125 VAC/30 VDC

Figure 5. Example Wiring Diagram with N.O. Monitoring

Installing Trim to Stile

1. INSTALL rivnuts.

2. INSTALL the 4581 Cam Plug into the 4300, 4500, or 4900 deadlatch, and SECURE with the

set screw on the latch.

3. INSERT the drive spindle into the trim body prior to mounting.

4. MOUNT the cover plate (not required for 1-1/2” backset) and the trim body to the stile using

two #10-32 x 7/8” flat head screws.

5. SLIDE the cover onto the trim body from the top.

NOTE: The groove on the shaft faces opposite to the latch bolt.

6. INSERT the shaft through the hole on the cover and the output on the trim body.

7. TIGHTEN the set screw with a 3/32” Allen wrench to secure the shaft (see Figure 6,

“Installing Trim to Stile”).

8. INSTALL the top cap using two #4-40 x 1/4” flat head screws (see Figure 6).

9. PUSH the cover up flush with the top cap, and INSTALL the bottom cap using a #6-32 x 1/4”

flat head screw (see Figure 6).

6 80-0180-418, Rev D

Figure 6. Installing Trim to Stile

Installing the Handle

1. INSERT washer and then INSERT hub

over the shaft, as required (see Figure 7,

“Installing the Handle”).

Figure 7. Installing the Handle

2. INSTALL the handle over the hub with the

hole aligned with the hole on the hub (see

Figure 7).

NOTE: The shaft detent should be aligned

with the locking screw.

3. SLIDE the handle in until it rests against

the trim cover.

Using a 1/8” Allen wrench, TIGHTEN the

lock screw to secure the handle to the

shaft (see Figure 7).

7 80-0180-418, Rev D

Determining and Changing the Handing Configuration

1. DETERMINE the current handing configuration(see Figure 8, “Handing Configuration”).

Figure 8. Handing Configuration

NOTE: During the next step, it is necessary to hold the monitor slide down to keep it from

popping out of place by the slide return spring.

1. IF a change of handing is required,

THEN PERFORM the following.

a. REMOVE both #4-40 x 1/4” screws and REMOVE the cover (see Figure 8).

b. REMOVE and FLIP the direction rack, ensuring the drive gear stays in position (see

Figure 8).

c. INSTALL cover.

d. SECURE cover using the two #4-40 x 1/4” screws

Changing the Handing of the 4581 Cam Disc

NOTE: Figure 9, “Changing the Handing of the 4581 Cam Disc,” provides an overall view for

the steps in this section.

Figure 9. Changing the Handing of the 4581 Cam Disc

8 80-0180-418, Rev D

1. DEPRESS the rear push cap.

2. While holding the rear push cap, SLIDE

the eagle beak cam down and out of

the front push cap and the dowel pin.

3. FLIP the eagle beak cam to the other

side, and SLIDE it in the dowel pin and

up to the front push cap.

4. Release the rear push cap to complete

the changing hand operation.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cerradura de puerta de Assa Abloy

Assa Abloy

Assa Abloy EMTEK LISCIO Guía de solución de problemas

Assa Abloy

Assa Abloy Corbin Russwin MP6600 Series Manual de usuario

Assa Abloy

Assa Abloy KESO Genie Manual de usuario

Assa Abloy

Assa Abloy 118 Series Manual de usuario

Assa Abloy

Assa Abloy Yale 6100 Manual de usuario

Assa Abloy

Assa Abloy Lockwood CAVITY LOCK Manual de usuario

Assa Abloy

Assa Abloy Sargent PE80 Series Manual de usuario

Assa Abloy

Assa Abloy KESO Manual de usuario

Assa Abloy

Assa Abloy Securitron DSB Series Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin Access 600 CL33600 TCRNE1... Manual de usuario

Assa Abloy

Assa Abloy 179C Manual de usuario

Assa Abloy

Assa Abloy Corbin Russwin EcoFlex NAC Series Instrucciones de montaje

Assa Abloy

Assa Abloy Corbin Russwin MP9800 Series Manual de usuario

Assa Abloy

Assa Abloy SARGENT 10X Series Manual de usuario

Assa Abloy

Assa Abloy Lockwood Cavity Lock Manual de usuario

Assa Abloy

Assa Abloy shine Manual de usuario

Assa Abloy

Assa Abloy RIXSON W0700 Series Manual de usuario

Assa Abloy

Assa Abloy EL460 Manual de usuario

Assa Abloy

Assa Abloy MSL mFlipLock basis Manual de usuario

Assa Abloy

Assa Abloy 179E Guía del usuario

Assa Abloy

Assa Abloy ES8100 Instrucciones de montaje

Assa Abloy

Assa Abloy SARGENT KP8977 Guía

Assa Abloy

Assa Abloy effeff Mini Magnet Manual de usuario

Assa Abloy

Assa Abloy Sargent 10G13 Manual de usuario

Manuales populares de Cerradura de puerta de otras marcas

We.lock

We.lock SECBNEBL51 Manual de usuario

Iseo

Iseo MA1A Manual de usuario

ID Lock

ID Lock 150 Manual de usuario

Lockly

Lockly ACCESS TOUCH PRO Manual de usuario

iLoq

iLoq G50S Manual de usuario

SDC

SDC Z7835 Manual de usuario

ilco

ilco 452 Manual de usuario

Samsung

Samsung shs-h705 Manual de usuario

TRU-BOLT

TRU-BOLT 08102017 Manual de usuario

CDVI

CDVI 500-LADJ Manual de usuario

Igloohome

Igloohome Deadbolt 2S Metal Grey Instrucciones de instalación y mantenimiento

eSSL

eSSL FL-300 Manual de usuario

JAKO

JAKO JKBTNX4 Manual de usuario

Dorma

Dorma MUNDUS PREMIUM GK 50 Guía del usuario

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manual de usuario

Yale

Yale MORTISE 8800 SERIES Manual de usuario

Siegenia

Siegenia KFV AS3500 Manual de usuario

Saflok

Saflok Quantum ädesē RFID Manual de usuario