Assa Abloy LCU9101 Manual de usuario
LCU9101
One-door control unit
Innehåll
Introduction.............................................................. 3
Compatible accessories............................................. 3
Motor lock..................................................................... 3
Readers........................................................................ 3
LCU9101 ................................................................... 4
LCU9101 with relay board......................................... 5
Description of the board .................................................... 6
Indications....................................................................... 7
Settings with DIP switches ................................................. 8
DIP1 Telnet................................................................... 8
DIP2 Initiate motor lock .................................................. 8
DIP3 Balanced door monitor switch .................................. 8
DIP4 Fixed IP 192.168.1.250 ........................................... 8
DIP6 Master reset and test mode ..................................... 8
Installation ............................................................... 9
Installation Relay board DAC400RC64.................................. 9
Jumper links................................................................ 10
Terminal blocks ........................................................... 11
Initiating motor lock ..................................................... 13
Connection of accessories ................................................ 14
IG559101931C.doc
2 LCU9101
Connection of direct connected motor lock....................... 14
Balanced Door monitor switch........................................ 14
Day/Night function ....................................................... 15
Blocking input ............................................................. 15
Door monitor switch (magnet) serial/parallel.................... 15
PoE (Power over Ethernet) ............................................ 16
Configuration.......................................................... 17
Introduction ................................................................ 17
Automatic configuration................................................... 17
Conditions................................................................... 17
Check list.................................................................... 18
Manual configuration....................................................... 19
Installation of drivers for USB configuration ..................... 19
Terminal software ........................................................ 20
Configuration via the terminal software ........................... 20
Terminal commands ..................................................... 23
Key handling ............................................................... 26
Technical information ............................................. 27
Dimensions.................................................................... 28
Diagram ........................................................................ 28
LCU9101 3
Introduction
LCU9101 is an IP based control unit for one door with full function
for handling of reader, electrical lock and motor lock directly.
LCU9101 is a Hi-O prepared control unit in the ARX family that
communicates with SLL encryption and handles certificates, for
the highest possible security.
LCU9101 contains all that is necessary for the door. All
connections for e.g. motor lock, reader, electric strike, exit
button, door monitor switch, alarm, door automatic etc. are to be
made here.
Compatible accessories
Motor lock
References to motor lock refers to direct control as follows:
Assa Classic 8000S, 8001S
Assa Classic 8087S
Abloy 8164-II, 8165-II, EL650-II
Assa Evolution 810S, 811S
Readers
LCU9101 handles magnetic readers, EM prox readers, Mifare
readers and Wiegand readers via interface 6390IF or via ADD ON
board 400RW22.
4 LCU9101
LCU9101
LCU9101 5
LCU9101 with relay board
6 LCU9101
Description of the board
00068e30075f
00068e30075f
WDG
A
B
C
D
Over load 12V Out
Over load RE1 12V Out
CL reader connected
RE 1
RE 2
LCU9101 7
Indications
There are LED’s on the board giving the following indications:
Power
(OK)
Green indication, indicates that system is powered.
WDG (OK) Blue indication, normal flash approx. 2 Hz
(2 flashes/sec.)
Unlit – LCU9101 is starting.
LED-lit – Error.
A(Yellow) Flashes slowly while the control unit tries to create
a connection with the ARX server. Lit when the
control unit is in contact with the ARX server.
B(Red) Lit when the control unit have messages to send to
the ARX server.
C(Green) Receiving data.
D(Green) Initiated CL motor lock found.
OL
(Overload)
Lit when the over voltage protection to 12V out,
pin +12V/0V (feeding reader etc.) is triggered.
CL (Red) Lit when readers are connected to the CL+/CL-
port.
12v Over
(Red)
Lit when the over voltage protection to 12V, via
RE1 NO/C, is triggered.
LED RE1/RE2 lit when the relay takes hold.
Link Lit at link.
Unlit when there is no link.
100M Lit at 100 Mbit communication.
Unlit when there is no 100 Mbit communication.
ACT Flashes at activity on the Ethernet port.
Unlit when there is no activity on the Ethernet
port.
8 LCU9101
Settings with DIP switches
DIP1 Telnet
If DIP1 is in position ON when LU9101 is started it is possible to
communicate with the control unit via Telnet. Used when the
control unit should be configured via the Ethernet contact.
DIP2 Initiate motor lock
DIP2 in position ON initiate “Current Loop” motor locks to work
together with control unit LCU9101. When the motor lock is
installed DIP2 is set to position ON and the control unit is
restarted. When the control unit has restarted LED “D” will turn
green when the motor lock is found and initiated. Set DIP2 to OFF
and replace a possible "Learn" jumper link on the motor lock.
DIP3 Balanced door monitor switch
DIP3 in position ON and two resistors of 2,2KΩmounted on the
door monitor switch, then restart the control unit.
DIP4 Fixed IP 192.168.1.250
Can be used when you want to set up the control unit with the aid
of a TP cable, used together with DIP1.
DIP6 Master reset and test mode
When DIP6 is set to ON the control unit performs a master reset
on all parameters at upstart and resets LCU9101 to the factory
settings, it also sets LCU9101 in test mode.
Note! When this is done the LCU9101 will lose all settings and
new information must be loaded to the LCU9101. In the test
mode you can check installed readers and lock, but not the motor
lock. Normal position for DIP6 is OFF.
LCU9101 9
Installation
The following section describes the physical installation of the
control unit and connection of accessories.
Installation Relay board DAC400RC64
To get access to all outputs and inputs relay board DAC400RC64
must be connected.
Connection of relay board is made as follows:
1. Turn off the power to LCU9101
2. Dislocate LCU9101 from the box
3. Align the contact pieces toward each other
4. Make sure that the boards are in level with each other
5. Push the boards together
6. Snap the boards to the box
7. Turn the power ON
LCU9101 + RC64 are ready for operation
10 LCU9101
Jumper links
Potential free contact
Val av NO/NC relä 1
(Ellås relä)
00068e30075f
00068e30075f
DIP-omkopplare
DIP1 Telnet ON/OFF
DIP2 I läge ON initiering motorlås
DIP3 Balanserad dörrbladslägeskontakt
DIP4 Fast IP 192.168.1.250
DIP5 Används ej
DIP6 Master reset samt testläge
12V ut (1=+, 2=-)
(12V Ut på relä 1)
12V In (1=+, 2=-)
(In spänning ut på relä 1)
Val av NO/NC relä 2
(LFK)
Hi-O terminering
Tabla de contenidos
Otros manuales de Unidad de control de Assa Abloy
Assa Abloy
Assa Abloy TRAKA UD0011 Manual de usuario
Assa Abloy
Assa Abloy Securitron B100 Manual de usuario
Assa Abloy
Assa Abloy LCU9101IV Manual de usuario
Assa Abloy
Assa Abloy EffEff 1338-14 Manual de usuario
Assa Abloy
Assa Abloy EffEff 1340-20 Manual de usuario
Assa Abloy
Assa Abloy OneSystem Service Module Manual de usuario
Assa Abloy
Assa Abloy effeff 720-40 Guía de inicio rápido
Assa Abloy
Assa Abloy OneSystem N5952 Manual de usuario
Assa Abloy
Assa Abloy HES iCLASS IC0020 Manual del propietario
Assa Abloy
Assa Abloy Norton ADAEZ Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
