ASROCK K7VT6-C Manual de usuario

K7VT6-C

User Manual

Version 1.0

PublishedDecember 2004

No part of this manual may be reproduced, transcribed, transmitted, or translated in

any language, in any form or by any means, except duplication of documentation by

the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this manual may or may not be regis-

tered trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:

Specifications and information contained in this manual are furnished for informa-

tional use only and subject to change without notice, and should not be constructed

as a commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this manual.

With respect to the contents of this manual, ASRock does not provide warranty of

any kind, either expressed or implied, including but not limited to the implied warran-

ties or conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the manual or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Contents

1. Introduction ....................................................... 4

1.1 Package Contents................................................................ 4

1.2 Specifications...................................................................... 5

1.3 Motherboard Layout ............................................................ 7

1.4 ASRock I/O PlusTM ............................................................................................................ 8

2. Installation ......................................................... 9

Pre-installation Precautions ......................................................... 9

2.1 CPU Installation .................................................................... 10

2.2 Installation of CPU Fan and Heatsink .................................. 10

2.3 Installation of Memory Modules (DIMM)............................... 11

2.4 Expansion Slots (PCI and AGP Slots) ................................. 12

2.5 Jumpers Setup .................................................................... 13

2.6 Onboard Headers and Connectors .................................... 15

3. BIOS Setup ......................................................... 17

3.1 BIOS Setup Utility ................................................................. 17

3.1.1 BIOS Menu Bar .......................................................... 17

3.1.2 Legend Bar ................................................................ 17

3.2 Main Menu ............................................................................ 18

3.3 Advanced, Security, Power, Boot, and Exit Menus ........... 20

4. Software Support .............................................. 21

4.1 Install Operating System ...................................................... 21

4.2 Support CD Information ........................................................ 21

4.2.1 Running Support CD .................................................. 21

4.2.2 Drivers Menu ............................................................. 21

4.2.3 Utilities Menu .............................................................. 21

4.2.4 Contact Information .................................................... 21

Appendix ............................................................... 22

1. Advanced BIOS Setup Menu............................................... 22

2. Security Setup Menu ........................................................... 27

3. Power Setup Menu .............................................................. 28

4. Boot Setup Menu ................................................................. 29

5. Exit Menu .............................................................................. 30

1. Introduction

Thank you for purchasing ASRock K7VT6-C motherboard, a reliable motherboard

produced under ASRock’s consistently stringent quality control. It delivers excellent

performance with robust design conforming to ASRock’s commitment to quality and

endurance.

Chapter 1 and 2 of this manual contain introduction of the motherboard and step-by-

step installation guide. Chapter 3 and 4 contain basic BIOS setup and support CD

information. More information of advanced BIOS setup can be found in Appendix on

page 22 for advanced users’ reference.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change

without notice. In case any modifications of this manual occur, the

updated version will be available on ASRock website without further

notice. You may find the latest memory and CPU support lists on

ASRock website as well. ASRock website http://www.asrock.com

1.1 Package Contents

1 x ASRock K7VT6-C Motherboard

(ATX Form Factor: 12.0-in x 7.0-in, 30.5 cm x 17.8 cm)

1 x ASRock K7VT6-C Quick Installation Guide

1 x ASRock K7VT6-C Support CD

1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)

1 x 3.5-in Floppy Drive Ribbon Cable

1 xASRock I/O PlusTM Shield

1.2 Specifications

Platform: ATX Form Factor: 12.0-in x 7.0-in, 30.5 cm x 17.8 cm

CPU: Supports Socket A (462 pins) for

AMDAthlonTM / AthlonTM XP / DuronTM/ SempronTM processor

Chipsets: North Bridge:

VIA KT600, FSB@200 / 266 / 333 / 400 MHz

South Bridge:

VIAVT8235CE, Supports USB 2.0, ATA 133

Memory: 2DDRDIMMSlots:DDR1andDDR2

PC3200 (DDR400) for 1DDRDIMM slot, Max. 1GB

PC2700(DDR333)/PC2100(DDR266)for2DDRDIMMslots,

Max. 2GB

IDE: IDE1:ATA133 / UltraDMAMode 6

IDE2:ATA133 / UltraDMAMode 6

Supports up to 4 IDE Devices

Floppy Port: Supports up to 2 Floppy Disk Drives

Audio: 5.1 Channels AC’97 Audio

LAN: Speed: 802.3u (10/100 Ethernet), Supports Wake-On-LAN

Hardware Monitor: CPU Temperature Sensing

Motherboard Temperature Sensing

CPU Overheat Shutdown to Protect CPU Life

(ASRock U-COP)(see CAUTION 1)

CPU Fan Tachometer

Chassis Fan Tachometer

Voltage Monitoring: +12V, +5V, +3.3V, Vcore

PCI slots: 5 Slots with PCI Specification 2.2

AGP slot: 1AGP Slot, Supports 1.5V, 8X/4X AGP Card (see CAUTION 2)

USB 2.0: 6 USB 2.0 ports:

include 6 ready-to-use USB 2.0 ports on the rear panel,

(see CAUTION 3)

ASRock I/O PlusTM:1 PS/2 Mouse Port, 1 PS/2 Keyboard Port,

1 Serial Port: COM1,

1 Parallel Port (ECP/EPP Support)

6 ready-to-use USB 2.0 Ports,

1 RJ-45 Port,

Audio Jack: Line In / Line Out / Microphone

BIOS: AMI legal BIOS, Supports “Plug and Play”,

ACPI 1.1 Compliance Wake-Up Events,

SMBIOS 2.3.1 Support,

CPU Frequency Stepless Control

(only for advanced users’ reference, see CAUTION 4)

OS: Microsoft® Windows® 98 SE / ME / 2000 / XP Compliant

CAUTION!

1. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

2. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard!

It may cause permanent damage!

3. Power Management for USB 2.0 works fine under Microsoft®Windows®

XP SP1/2000 SP4. It may not work properly under Microsoft®Windows®

98/ME.

4. Although this motherboard offers stepless control, it is not recommended

to perform over clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU. The CPU host frequency of this motherboard is determined by

jumper-setting. You must adjust “FSB Select Jumpers” according to the

FSB of your AMD CPU before you set the “CPU Host Frequency” con-

figuration as “Manual” in BIOS. See page 13 for the details of “FSB Select

Jumpers” adjustment, and page 22 of “User Manual” in the Support CD for

“CPU Host Frequency” configuration.

17.8cm (7.0 in)

DDR 1 (64/72 bit, 184-pin module)

DDR2 (64/72 bit, 184-pin module)

PCI2

PCI3

PCI4

PCI5

PCI1

1.5V_AGP1

SPEAKER1

HDLED RST

PLED PWRBTN

PANEL1

2Mb

BIOS

FLOPPY1

SUPER

I/O

CLRCMOS2

VIA

VT8235CE

CPU_FAN1

CHA_FAN1

CMOS

BATTERY

PS2_USB_PWR1

IDE1 IDE2

USB2.0

5.1CH

ATA133

K7VT6-C

VIA

KT600

CHIPSET

ATXPWR1

AUX1 CD1

PARALLEL PORT

PS/2

MOUSE

PS/2

KEYBOARD

SERIAL

PORT

(COM1)

30.5cm (12.0 in)

LAN

PHY

AUDIO

CODEC

12 36

DDR400

FSB 400

PWR_LED1

1FSB_SEL0

FSB_SEL1

FSB_SEL2

FID3

FID2

FID1

FID0

FID4 1

SOCKET 462

AUDIO1

GAME1

JUSB45

Top:

Line In

Center:

Line Out

Bottom:

Mic In

USB 2.0

T: USB4

B: USB5

JR1 JL1

USB 2.0

T: USB2

B: USB3

USB 2.0

T: USB0

B: USB1

Top:

RJ-45

1718

AGP 8X

1.3 Motherboard Layout

1 PS2_USB_PWR1 Jumper 14 System Panel Connector (PANEL1)

2 CPU Fan Connector (CPU_FAN1) 15 Chassis Speaker Connector (SPEAKER1)

3 CPU Socket 16 Floppy Connector (FLOPPY1)

4 North Bridge Controller 17 Internal Audio Connector: CD1 (Black)

5 184-pin DDR DIMM Slots (DDR1- 2) 18 Internal Audio Connector: AUX1 (White)

6 ATX Power Connector (ATXPWR1) 19 Clear CMOS Jumper (CLRCMOS2)

7 Secondary IDE Connector (IDE2, Black) 20 JR1 / JL1 Jumpers

8 Primary IDE Connector (IDE1, Blue) 21 Front Panel Audio Connector (AUDIO1)

9 AGP Slot (1.5V_AGP1) 22 PCI Slots (PCI1- 5)

10 FSB Select Jumpers 23 Game Port Connector (GAME1)

(FSB_SEL0,FSB_SEL1, FSB_SEL2) 24 Flash Memory

11 South Bridge Controller 25 Shared USB 2.0 Header (JUSB45, Blue)

12 Power LED Connector (PWR_LED1) 26 J1 Jumper (FID0, FID1, FID2, FID3, FID4)

13 Chassis Fan Connector (CHA_FAN1)

1.4 ASRock I/O PlusTM

1 Parallel Port 7 2 x USB 2.0 Port (USB0, USB1)

2 RJ-45 Port 8 2 x USB 2.0 Port (USB2, USB3)

3 Line In (Light Blue) 9 Serial Port: COM1

4 Line Out (Lime) 10 PS/2 Keyboard Port (Purple)

5 Microphone (Pink) 11 PS/2 Mouse Port (Green)

6 2 x Shared USB 2.0 Port (USB4, USB5)

8910

2. Installation

K7VT6-C is an ATX form factor (12.0-in x 7.0-in, 30.5 cm x 17.8 cm) motherboard.

Before you install the motherboard, study the configuration of your chassis to en-

sure that the motherboard fits into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard

components or change any motherboard settings.

Before you install or remove any component, ensure that the

power is switched off or the power cord is detached from the

power supply. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

1. Unplug the power cord from the wall socket before touching any

component.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet or

the like. Also remember to use a grounded wrist strap or touch a

safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded anti-

static pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the motherboard

to the chassis, please do not over-tighten the screws! Doing so may

damage the motherboard.

2.1 CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90oangle.

Step 2. Position the CPU directly above the socket such that its marked corner

matches the base of the socket lever.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the

CPU into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

2.2 Installation of CPU Fan and Heatsink

AMDAthlonTM /AthlonTM XP/DuronTM family CPUs with a speed of 600 MHz and

higher require larger heatsink and cooling fan. Thermal grease between the

CPU and the heatsink is also needed to improve heat transfer. Make sure that

the CPU and the heatsink are securely fastened and in good contact with

each other. Then connect the CPU fan to the CPU FANconnector (CPU_FAN1,

see page 7, No. 2). For proper installation, please kindly refer to the instruc-

tion manuals of the CPU fan and heatsink vendors.

Step 1 Step 2, 3 Step 4

Otros manuales para K7VT6-C

Tabla de contenidos

Otros manuales de Placa madre de ASROCK

ASROCK

ASROCK 760GM-GS3 Manual de usuario

ASROCK

ASROCK G41MH-GE Manual de usuario

ASROCK

ASROCK N68-GS4/USB3 FX R2.0 Manual de usuario

ASROCK

ASROCK 775XFIRE-ESATA2 - 02-2006 Manual de usuario

ASROCK

ASROCK X79 Extreme4-M Manual de usuario

ASROCK

ASROCK Z170M OC Formula Manual de usuario

ASROCK

ASROCK A785GM-LE - V1.0 Manual de usuario

ASROCK

ASROCK J3455B-ITX Manual de usuario

ASROCK

ASROCK B365 Pro4 Manual de usuario

ASROCK

ASROCK H67M-GE/HT Manual de usuario

ASROCK

ASROCK B75M-GL R2.0 Manual de usuario

ASROCK

ASROCK A320M/ac Manual de usuario

ASROCK

ASROCK 785G Pro Manual de usuario

ASROCK

ASROCK IMB-A160-H Manual de usuario

ASROCK

ASROCK H570 Steel Legend Manual de usuario

ASROCK

ASROCK IMB-790 Manual de uso y cuidado

ASROCK

ASROCK P55 DELUXE3 - Manual de usuario

ASROCK

ASROCK H81 Pro BTC Manual de usuario

ASROCK

ASROCK AD2700-ITX Manual de usuario

ASROCK

ASROCK 785GM-GS3 - V1.0 Manual de usuario

ASROCK

ASROCK X570 Steel Legend Manual de usuario

ASROCK

ASROCK FM2A55M-VG3 Manual de usuario

ASROCK

ASROCK N68-GE3 UCC - Manual de usuario

ASROCK

ASROCK A230GC Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario