ASROCK GE PRO-HT R3.0 Manual de usuario

GE Pro-HT

GE Pro-M2

User Manual

Version 3.0

Published July 2003

No part of this manual may be reproduced, transcribed, transmitted, or translated in

any language, in any form or by any means, except duplication of documentation by

the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this manual may or may not be regis-

tered trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:

Specifications and information contained in this manual are furnished for informa-

tional use only and subject to change without notice, and should not be constructed

as a commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this manual.

With respect to the contents of this manual, ASRock does not provide warranty of

any kind, either expressed or implied, including but not limited to the implied warran-

ties or conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the manual or product.

ASRock Website: http://www.asrock.com

Contents

1 Introduction.................................................... 4

1.1 Package Contents ........................................................... 4

1.2 Specifications ................................................................. 5

1.3 Motherboard Layout (GE Pro-HT) .................................. 7

1.4 Motherboard Layout (GE Pro-M2) .................................. 8

1.5 ASRock I/OTM (GE Pro-HT / GE Pro-M2) .......................... 9

2 Installation ...................................................... 10

2.1 Screw Holes ................................................................... 10

2.2 Pre-installation Precautions ............................................ 10

2.3 CPU Installation ............................................................... 11

2.4 Installation of Heatsink and CPU fan .............................. 11

2.5 Installation of Memory Modules (DIMM) .......................... 12

2.6 Expansion Slots .............................................................. 12

2.7 Jumpers Setup ................................................................ 13

2.8 Connectors ..................................................................... 14

3 BIOS Setup ...................................................... 16

3.1 BIOS Setup Utility ............................................................ 16

3.1.1 BIOS Menu Bar ..................................................... 16

3.1.2 Legend Bar ........................................................... 16

3.2 Main Menu ....................................................................... 17

3.3 Advanced, Security, Power, Boot, and Exit Menus ...... 19

4 Software Support ........................................... 20

4.1 Installing Operating System ............................................ 20

4.2 Support CD Information ................................................... 20

4.2.1 Running Support CD ............................................. 20

4.2.2 Drivers Menu ........................................................ 20

4.2.3 Utilities Menu ......................................................... 20

4.2.4 ASRock “PC-DIY Live Demo” Program ................. 20

4.2.5 Contact Information............................................... 20

Appendix ........................................................... 21

1. Advanced Menu ............................................................. 21

2. Security Menu ................................................................. 25

3. Power Menu ................................................................... 26

4. Boot Menu ....................................................................... 27

5. Exit Menu......................................................................... 28

Chapter 1 Introduction

Thank you for purchasing ASRock GE Pro-HT / GE Pro-M2 motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control. It de-

livers excellent performance with robust design conforming to ASRock’s commit-

ment to quality and endurance.

Chapter 1 and 2 of this manual contain introduction of the motherboard and step-by-

step installation guide for new DIY system builders. Chapter 3 and 4 contain basic

BIOS setup and Support CD information.

For advanced users’ reference, the Appendix appearing on page 21 offers more

advanced BIOS setup information.

Because the motherboard specifications and the BIOS software

might be updated, the content of this manual will be subject to

change without notice. In case any modifications of this manual

occur, the updated version will be available on ASRock website

without further notice. You may find the latest memory and CPU

support lists on ASRock website as well.

ASRock website http://www.asrock.com

1.1 Package Contents

ASRock GE Pro-HT or GE Pro-M2 motherboard

(Micro ATX form factor: 9.6" x 7.5", 24.4 x 19.1 cm)

ASRock GE Pro-HT / GE Pro-M2 Quick Installation Guide

ASRock Intel-SiS Support CD

1 cable for IDE devices (1 x ATA 66 / 100 / 133)

1 cable for floppy drive (1 x ribbon cable)

1 ASRock I/O shield

1 COM port bracket

1 ASRock MR card (Optional)

1.2 Specifications

Platform: Micro ATX form factor (9.6" x 7.5", 24.4 x 19.1 cm)

CPU: Socket 478 for Intel®Pentium®4 / Celeron®processor

Chipsets: North Bridge (GE Pro-HT):

SiS 651 chipset, FSB @ 533/400MHz,

supports Hyper-Threading Technology (see CAUTION 1);

North Bridge (GE Pro-M2):

SiS 533/333 chipset, FSB @ 533/400MHz;

South Bridge: SiS 962L chipset, supports USB 2.0, ATA 133

VGA: SiS Real 256E, 4MB-64MB VRAM (share memory)

Memory: 2DDRDIMM slots:DDRDIMM1 andDDRDIMM2

support PC1600 (DDR200) / PC2100 (DDR266) /

PC2700 (DDR333), Max. 2GB;

IDE: IDE1: ATA 133 / Ultra DMA Mode 6;

IDE2: ATA 133 / Ultra DMA Mode 6;

Can connect up to 4 IDE devices

Floppy Port: Supports 2 floppy disk drives

Audio: 5.1 channels AC’97 Audio

LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN

Hardware Monitor: CPU temperature sensing (ASRock U-COP);

Chassis temperature sensing;

CPU overheat shutdown to protect CPU life (ASRock U-COP)

(see CAUTION 2);

Voltage monitoring: +12V, +5V, +3V, Vcore;

CPU fan tachometer; Chassis fan tachometer

PCI slots: 2 slots with PCI Specification 2.2

AGP slot: 1 universal AGP slot, AGP 2.0 compliant,

supports 3.3V / 1.5V, 4X / 2X / 1X AGP card

AMR slot: 1 slot, supports ASRock MR card (Optional)

USB 2.0: 4 default USB 2.0 ports and 1 extra set of header for 2 additional

USB 2.0 ports upgrade (see CAUTION 3)

ASRock I/OTM:PS/2: 1 keyboard port / 1 mouse port;

1 RJ 45 port; 4 rear default USB 2.0 ports;

1 VGA port; 1 parallel port: ECP/EPP support;

Audio Jack: Line Out/ Line In/ Microphone + Game port

BIOS: AMI legal BIOS; Supports “Plug and Play”;

ACPI 1.1 compliance wake up events;

Supports jumperfree; SMBIOS 2.3.1 support;

CPU frequency stepless control

(only for advanced users’ reference, see CAUTION 4)

OS: Microsoft®Windows®98SE / ME / 2000 / XP compliant

CAUTION!

1. About the setting of “Hyper Threading Technology”, please check page 21.

2. While CPU overheat is detected, the system will automatically shutdown.

Please check if the CPU fan on the motherboard functions properly before

you resume the system. To improve heat dissipation, remember to spray

thermal grease between the CPU and the heatsink when you install the PC

system.

3. Power Management for USB 2.0 works fine under Microsoft®Windows®

XP. It may not work properly under Microsoft®Windows®98/ME/2000.

Please refer to Microsoft®official document at

http://www.microsoft.com/whdc/hwdev/bus/USB/USB2support.mspx

4. Although GE Pro-HT / GE Pro-M2 offers stepless control, it is not

recommended to perform over clocking. When the CPU frequency of

GE Pro-HT / GE Pro-M2 is set to perform over clocking, other clocks, such

as PCI clock, AGP clock and Memory clock will also be overclocked

proportionally. Frequencies other than the recommended CPU bus

frequencies may cause the instability of the system or damage the CPU

and the motherboard.

1.3 Motherboard Layout (GE Pro-HT)

1 PS2_USB_PWR1 Jumper 16 Clear CMOS (CLRCMOS1, solder points)

2 CPU Heatsink Retention Module 17 External Speaker Connector (SPEAKER1)

3 CPU Socket 18 Infrared Module Connector (IR1)

4 CPU Fan Connector (CPU_FAN1) 19 AMR Slot (AMR1)

5 North Bridge Controller 20 Serial Port Connector (COM1)

6 184-pin DDR DIMM Slots (DDR DIMM1- 2) 21 Flash Memory

7 Primary IDE Connector (IDE1, Blue) 22 AUDIO CODEC

8 Secondary IDE Connector (IDE2, Black) 23 Front Panel Audio Connector (AUDIO1)

9 Accelerated Graphics Port (AGP1) 24 JR1 Jumper

10 South Bridge Controller 25 JL1 Jumper

11 PCI Slots (PCI 1- 2) 26 Internal Audio Connector: CD1 (Black)

12 USB 2.0 Header (USB45, Blue) 27 Internal Audio Connector: AUX1 (White)

13 Chassis Fan Connector (CHA_FAN1) 28 LAN PHY

14 System Panel Connector (PANEL1) 29 ATX Power Connector (ATXPWR1)

15 Floppy Connector (FLOPPY1)

GE PRO-HT

DDR DIMM1 (64/72 bit, 184-pin module)

DDR DIMM2 (64/72 bit, 184-pin module)

IDE2

IDE1

FLOPPY1

AMR1

COM1

USB45

IR1

SPEAKER1

CHA_FAN1

SiS

962L

CMOS

Battery

PCI 2

PCI 1

Super

I/O

2MB

BIOS

AUDIO1

JR1

JL1

AUDIO

CODEC

PS2_USB_PWR1

SiS

651

Chipset

mPGA478B

ATXPWR1

Mic

GAME AUDIO1

LAN

(optional)

USB 2.0

Ports

Mic in

Line out

GAME AUDIO1

PARALLEL PORT

PS/2

Mouse

PS/2

Keyboard

VGA

Line

Line in

USB 2.0

Ports

AGP1

CPU_FAN1

19.1cm (7.5 in)

24.4cm (9.6 in)

AUX1 CD1

214

5.1CH

PANEL1

HDLED RESET

PLED PWRBTN

LAN

PHY

CLRCMOS1

3 5

151617

1920

1.4 Motherboard Layout (GE Pro-M2)

1 PS2_USB_PWR1 Jumper 16 Clear CMOS (CLRCMOS1, solder points)

2 CPU Heatsink Retention Module 17 External Speaker Connector (SPEAKER1)

3 CPU Socket 18 Infrared Module Connector (IR1)

4 CPU Fan Connector (CPU_FAN1) 19 AMR Slot (AMR1)

5 North Bridge Controller 20 Serial Port Connector (COM1)

6 184-pin DDR DIMM Slots (DDR DIMM1- 2) 21 Flash Memory

7 Primary IDE Connector (IDE1, Blue) 22 AUDIO CODEC

8 Secondary IDE Connector (IDE2, Black) 23 Front Panel Audio Connector (AUDIO1)

9 Accelerated Graphics Port (AGP1) 24 JR1 Jumper

10 South Bridge Controller 25 JL1 Jumper

11 PCI Slots (PCI 1- 2) 26 Internal Audio Connector: CD1 (Black)

12 USB 2.0 Header (USB45, Blue) 27 Internal Audio Connector: AUX1 (White)

13 Chassis Fan Connector (CHA_FAN1) 28 LAN PHY

14 System Panel Connector (PANEL1) 29 ATX Power Connector (ATXPWR1)

15 Floppy Connector (FLOPPY1)

GE PRO-M2

DDR DIMM1 (64/72 bit, 184-pin module)

DDR DIMM2 (64/72 bit, 184-pin module)

IDE1

FLOPPY1

AMR1

COM1

USB45

IR1

SPEAKER1

CHA_FAN1

SiS

962L

CMOS

Battery

PCI 2

PCI 1

Super

I/O

2MB

BIOS

AUDIO1

JR1

JL1

AUDIO

CODEC

PS2_USB_PWR1

SiS

533/333

Chipset

mPGA478B

ATXPWR1

Mic

GAME AUDIO1

LAN

(optional)

USB 2.0

Ports

Mic in

Line out

GAME AUDIO1

PARALLEL PORT

PS/2

Mouse

PS/2

Keyboard

VGA

Line

Line in

USB 2.0

Ports

AGP1

CPU_FAN1

19.1cm (7.5 in)

24.4cm (9.6 in)

AUX1 CD1

214

PANEL1

HDLED RESET

PLED PWRBTN

LAN

PHY

CLRCMOS1

3 5

151617

1920

IDE2

5.1CH

1.5 ASRock I/OTM (GE Pro-HT / GE Pro-M2)

1 Parallel Port 6 Line Out (Lime)

2 RJ-45 Port 7 USB 2.0 Ports

3 Game Port 8 VGA Port

4 Microphone (Pink) 9 PS/2 Keyboard Port (Purple)

5 Line In (Light Blue) 10 PS/2 Mouse Port (Green)

Chapter 2 Installation

GE Pro-HT / GE Pro-M2 is a Micro ATX form factor (9.6" x 7.5", 24.4 x 19.1 cm)

motherboard. Before you install the motherboard, study the configuration of your

chassis to ensure that the motherboard fits into it.

Make sure to unplug the power cord before installing or removing the

motherboard. Failure to do so may cause physical injuries to you and

damages to motherboard components.

2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard to the

chassis.

Do not over-tighten the screws! Doing so may damage the

motherboard.

2.2 Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any component.

2. To avoid damaging the motherboard components due to static electricity, NEVER

place your motherboard directly on the carpet or the like. Also remember to use

a grounded wrist strap or touch a safety grounded object before you handle

components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded antistatic pad or

in the bag that comes with the component.

Before you install or remove any component, ensure that the power is

switched off or the power cord is detached from the power supply.

Failure to do so may cause severe damage to the motherboard,

peripherals, and/or components.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de ASROCK

ASROCK

ASROCK Z97 Extreme9 Manual de usuario

ASROCK

ASROCK 939A790GMH Manual de usuario

ASROCK

ASROCK CONROE945PL-GLAN Manual de usuario

ASROCK

ASROCK IMB-150 Manual de usuario

ASROCK

ASROCK B365 PHANTOM GAMING 4 Manual de usuario

ASROCK

ASROCK Z97 Extreme6 Manual de usuario

ASROCK

ASROCK Fatal1ty B85 Killer Manual de usuario

ASROCK

ASROCK B460 Pro4 Manual de usuario

ASROCK

ASROCK IMB-184-PY Manual de usuario

ASROCK

ASROCK A68M-ITX Manual de usuario

ASROCK

ASROCK 980DE3/U3S3 Manual de usuario

ASROCK

ASROCK Z77 Pro4-M Manual de usuario

ASROCK

ASROCK NF6-GLAN Manual de usuario

ASROCK

ASROCK Fatal1ty Z97M Killer Series Manual de usuario

ASROCK

ASROCK 4Core1600-GLAN Manual de usuario

ASROCK

ASROCK Z590 Phantom Gaming-ITX/TB4 Manual de usuario

ASROCK

ASROCK X299 Steel Legend Manual de usuario

ASROCK

ASROCK H61M - ANNEXE 392 Manual de usuario

ASROCK

ASROCK IMB-1211-D Manual de usuario

ASROCK

ASROCK B550 PG Velocita Manual de usuario

ASROCK

ASROCK K8NF6P-VSTA Manual de usuario

ASROCK

ASROCK Industrial 4x4 R1000 Manual de instrucciones

ASROCK

ASROCK Fatal1ty Z68 Professional Gen3 Manual de usuario

ASROCK

ASROCK AD2700-ITX Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario