ASROCK ALIVENF4G-DVI Manual de usuario

Guide to SATA Hard Disks

Installation and RAID Configuration

1. Guide to SATA Hard Disks Installation............................. 2

1.1 Serial ATA (SATA) Hard Disks Installation ............... 2

1.2 Making a SATADriver Diskette ................................. 3

2. Guide to RAID Configurations.......................................... 4

2.1 Introduction of RAID ................................................ 4

2.2 RAID Configuration Precautions ............................ 6

2.3 BIOS Configuration Utility ....................................... 7

2.3.1 Enter BIOS Configuration Utility................ 7

2.3.2 Create Disk Array ....................................... 8

1. Guide to SATA Hard Disks Installation

1.1 Serial ATA (SATA) Hard Disks Installation

This motherboard adopts nVidia nForce3 chipset that supports

Serial ATA (SATA) hard disks with RAID functions, including RAID

0, RAID 1, and JBOD. You may install SATA hard disks on this

motherboard for internal storage devices. For SATA installation

guide, please refer to Serial ATA (SATA) Hard Disks Installation of

“User Manual ” in the support CD. This section will guide you how

to create RAID on SATA ports.

1.2 Making a SATA Driver Diskette

If you just want to install Windows 2000, Windows XP or

Windows XP 64-bit on your SATA HDDs without RAID functions,

there is no need to make a SATA driver diskette. However, if you

want to install Windows 2000, Windows XP or Windows XP 64-

bit on your SATA HDDs with RAID functions, you will need to

make an SATA driver diskette before you start the OS installation.

STEP1: Insert the Support CD into your optical drive to boot your

system. (Do NOT insert any floppy diskette into the

floppy drive at this moment!)

STEP2: During POST at the beginning of system boot-up, press

<F11> key, and then a window for boot devices

selection appears. Please select CD-ROM as the boot

device.

STEP3: When you see the message on the screen, “Do you

want to generate Serial ATA driver diskette [YN]?”,

press <Y>.

STEP4: Then you will see these messages,

Please insert a diskette into the floppy drive.

WARNING! Formatting the floppy diskette will

lose ALL data in it!

Start to format and copy files [YN]?

Please insert a floppy diskette into the floppy drive, and

press <Y>.

STEP5: The system will start to format the floppy diskette and

copy SATA drivers into the floppy diskette.

Once you have the SATA driver diskette ready, you may start to

install Windows 2000 / Windows XP / Windows XP 64-bit on your

system directly without setting the RAID configuration on your

system, or you may start to use “RAID BIOS Setting Utility” in the

section 2.3 to set RAID 0 / RAID 1 / JBOD configuration before you

install the OS. You may also set the RAID configuration by using

“RAID Utility for Windows” in Windows environment. Please refer

to the document in the Support CD, “Guide to RAID Utility for

Windows”, which is located in the folder at the following path:

.. \ RAID Utility for Windows

2. Guide to RAID Configurations

2.1 Introduction of RAID

This motherboard adopts nVidia nForce3 chipset that integrates

RAID controller supporting RAID 0 / RAID 1 / JBOD function with

two independent Serial ATA (SATA) channels. This section will

introduce the basic knowledge of RAID, and the guide to

configure RAID 0, RAID 1, and JBOD settings.

RAID

The term “RAID” stands for “Redundant Array of Independent

Disks”, which is a method combining two or more hard disk drives

into one logical unit. For optimal performance, please install

identical drives of the same model and capacity when creating a

RAID set.

RAID 0 (Data Striping)

RAID 0 is called data striping that optimizes two identical hard disk

drives to read and write data in parallel, interleaved stacks. It will

improve data access and storage since it will double the data

transfer rate of a single disk alone while the two hard disks

perform the same work as a single drive but at a sustained data

transfer rate.

WARNING!!

Although RAID 0 function can improve the access performance, it

does not provide any fault tolerance. Hot-Plug any HDDs of the

RAID 0 Disk will cause data damage or data loss.

RAID 1 (Data Mirroring)

RAID 1 is called data mirroring that copies and maintains an

identical image of data from one drive to a second drive. It

provides data protection and increases fault tolerance to the

entire system since the disk array management software will

direct all applications to the surviving drive as it contains a

complete copy of the data in the other drive if one drive fails.

JBOD (Spanning)

A spanning disk array is equal to the sum of all drives. Spanning

stores data onto a drive until it is full then proceeds to store files

onto the next drive in the array. When any member disk fails, it

will affect the entire array. JBOD is not really a RAID, and it does

not support fault tolerance.

2.2 RAID Configurations Precautions

1. Please use two new drives if you are creating a RAID 0

(striping) array for performance. It is recommended to

use two SATA drives of the same size. If you use two

drives of different sizes, the smaller capacity hard disk

will be the base storage size for each drive. For

example, if one hard disk has an 80GB storage capacity

and the other hard disk has 60GB, the maximum storage

capacity for the 80GB-drive becomes 60GB, and the

total storage capacity for this RAID 0 set is 120GB.

2. You may use two new drives, or use an existing drive

and a new drive to create a RAID 1 (mirroring) array for

data protection (the new drive must be of the same size

or larger than the existing drive). If you use two drives

of different sizes, the smaller capacity hard disk will be

the base storage size. For example, if one hard disk has

an 80GB storage capacity and the other hard disk has

60GB, the maximum storage capacity for the RAID 1 set

is 60GB.

3. Please verify the status of your hard disks before you

set up your new RAID array.

WARNING!!

Please backup your data first before you create RAID functions.

In the process you create RAID, the system will ask if you want to “Clear

Disk Data” or not. It is recommended to select “Yes”, and then your future

data building will operate under a clean environment.

BIOS SETUP UTILITY

IDE Configuration

Config SATA operation

mode.

Select Screen

Select Item

+- Change Option

F1 General Help

F10 Save and Exit

ESC Exit

Advanced

Primary IDE Master

Primary IDE Slave

Secondary IDE Master

Secondary IDE Slave

SATA1

SATA2

[Hard Disk]

[Not Detected]

[ATAPI CDROM]

[Not Detected]

OnBoard IDE Controller

OnBoard SATA Controller

[Both]

[Enabled]

SATA Operation Mode [RAID]

2.3 BIOS Setup Utility

2.3.1 Enter BIOS Setup Utility

After the system powers on, press <F2> key to enter BIOS setup

utility. Highlight Advanced and press <Enter>, then the main inter-

face of BIOS setup utility will appear. Please set the option SATA

Operation Mode to [RAID].

NVIDIA RAID IDE ROM BIOS 4.81

Detecting array . . .

Press F10 to enter RAID setup utility . . .

After the below window appears, please press <F10> to enter the

NVIDIARAIDUtility.

2.3.2 Create Disk Array

Create RAID 0

After the system powers on, press <F2> key to enter BIOS setup

utility. Highlight Advanced and press <Enter>, then the main interface

of BIOS setup utility will appear. Please set the option SATA Opera

tion Mode to [RAID].

BIOS SETUP UTILITY

IDE Configuration

Config SATA operation

mode.

Select Screen

Select Item

+- Change Option

F1 General Help

F10 Save and Exit

ESC Exit

Advanced

Primary IDE Master

Primary IDE Slave

Secondary IDE Master

Secondary IDE Slave

SATA1

SATA2

[Hard Disk]

[Not Detected]

[ATAPI CDROM]

[Not Detected]

OnBoard IDE Controller

OnBoard SATA Controller

[Both]

[Enabled]

SATA Operation Mode [RAID]

NVIDIA RAID IDE ROM BIOS 4.81

Detecting array . . .

0 Healthy NVIDIA RAID 0 74.54G

Press F10 to enter RAID setup utility . . .

Then, the below window appears.

After rebooting your computer, wait until you see the RAID software

prompting you to press <F10>. The RAID prompt appears as a part of

the system POST and boot process prior to loading the OS. You have

a few seconds to press <F10> before the window disappears.

NVIDIA RAID Utility Jan 12 2005

- Define a New Array -

Mirroring

Striping

Stripe Mirroring

Spanning

RAID Mode :

Free Disks

Loc Disk

1.0.M Maxt

1.1.M Maxt []Add

[]Del

Stripimg Block :

Array Disks

Loc Disk Model Name

Optimal

[ESC] Quit [F6] Back [F7] Finish [TAB] Navigate [ ] Select [ENTER] Popup

After you press <F10>, the NVIDIA RAID Utility - Define a New Array

window appears. By default, RAID Mode is set to Mirroring, but

please set it to Striping if you want to create RAID 0. And the

Striping Block is set to Optimal as default.

NVIDIA RAID Utility Jan 12 2005

- Define a New Array -

Striping

RAID Mode :

Free Disks

Loc Disk Model Name

1.0.M Maxt 6Y120M0

1.1.M Maxt 6Y120M0 []Add

[]Del

Stripimg Block :

Array Disks

Loc Disk Model

[ESC] Quit [F6] Back [F7] Finish [TAB] Navigate [ ] Select [ENTER] Popup

Optimal

16K

32K

64K

128K

Optim

Striping block size is given in kilobytes, and affect how data is

arranged on the disk. It is recommended to leave this value at the

default Optimal, which is 64KB, but the values can be between 8KB

and 128KB (8, 16, 32, 64, and 128KB). Then, you have to assign the

disks. The disks that you enabled from the RAID Config BIOS setup

page appear in the Free Disks block. These are the drives that are

available for use as RAID array disk,

1. Tab to the Free Disks section.

The first disk in the list is selected.

2. Move it from the Free Disks block to the Array Disks block by

pressing the right-arrow key.

3. Continue pressing the right-arrow key until all the disks that you

want to use as RAID array disks appear in the Array Disks block.

NVIDIA RAID Utility Jan 12 2005

- Define a New Array -

RAID Mode :

Free Disks

Loc Disk Model Name

1.0.M Maxtor 6Y120M0

1.1.M Maxtor 6Y120M0

[]Add

[]Del

Stripimg Block :

Array Disks

Loc Disk Model Name

Optimal

[ESC] Quit [F6] Back [F7] Finish [TAB] Navigate [ ] Select [ENTER] Popup

Striping

After assigning your RAID array disks, press <F7> to save your

changes of RAID array disks.

Otros manuales para ALIVENF4G-DVI

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de ASROCK

ASROCK

ASROCK Q1900B-ITX Manual de usuario

ASROCK

ASROCK X300TM-ITX Manual de usuario

ASROCK

ASROCK H61DE/SI Manual de usuario

ASROCK

ASROCK N68-GS4/USB3 FX R2.0 Manual de usuario

ASROCK

ASROCK H61M-PS Manual de usuario

ASROCK

ASROCK B760M-H/M.2 Manual de usuario

ASROCK

ASROCK DeskMeet B660 Series Manual de usuario

ASROCK

ASROCK H61M-VS - ANNEXE 811 Manual de usuario

ASROCK

ASROCK FM2A78M-HD+ R2.0 Manual de usuario

ASROCK

ASROCK N68C-S Manual de usuario

ASROCK

ASROCK B85 Anniversary Manual de usuario

ASROCK

ASROCK 890FX Deluxe4 Manual de usuario

ASROCK

ASROCK B85M-HDS Manual de usuario

ASROCK

ASROCK K8 COMBO-Z Manual de usuario

ASROCK

ASROCK X58 SUPERCOMPUTER - Manual de usuario

ASROCK

ASROCK Fatal1ty 990FX Professional Manual de usuario

ASROCK

ASROCK ALIVENF5-ESATA2 -2943 - Manual de usuario

ASROCK

ASROCK G41M-VS3 Manual de usuario

ASROCK

ASROCK X79 Extreme9 Manual de usuario

ASROCK

ASROCK H110M-DGS/D3 Manual de usuario

ASROCK

ASROCK CONROE1333-D667 - INSTALLATION 11-2007 Manual de usuario

ASROCK

ASROCK E3C204 Manual de usuario

ASROCK

ASROCK 960GM-GS3 FX Manual de usuario

ASROCK

ASROCK X399M Taichi Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario