AsReader ASX-520R Manual de usuario

AsReader（ASX-520R & ASR-020D）

Barcode Parameter Manual

Asterisk, Inc.

Version 1.1

※The data will be changed without a notice.

This document describes the programmable parameters, provides bar codes for programming, AsReader is

shipped with the factory default settings. These factory default values are stored in non-volatile memory

and are preserved even when the scan engine is powered down. Changes to the factory default values are

also stored in non-volatile memory and are preserved even when the scan engine is powered down. Scan the

appropriate bar codes included in this document. The new values replace the existing memory values. The

factory default parameter values can be recalled by scanning Set Factory Defaults.

Revision History

Version

Date

Item

1.0

16 March 2015

First Rivision

1.1

16 June 2016

A-1 Fix tipographical error at Parameter Defaults

B-13 Delete Decode LED Behavior

B-16 Delete “Host”from Trigger Mode

B-11 Add Decode Aiming Pattern

B-13 Add Decoding Illumination

To set the parameter

Charge the battery of AsReader, before setting the parameters.

Changing Default Values

The decoder ships with the settings shown in the Table on page

A-1

. If the default

values suit requirements, programming is not necessary.

Scan the appropriate barcodes in this guide to change a parameter value.

These new values replace the standard default values in memory.

To return all features to default values, scan Restore Defaults on page

B-1

. Throughout

the programming barcode menus, asterisks (*) indicate default values.

A-1

Parameter Default setting (factory default)

Parameter

Value

Page

User Preferences

Default parameter

Restore Defaults

B-1

Parameter Scanning

Enable

B-2

Lock Parameter Scanning

Disable

B-3

Unlock Parameter Scanning

Disable

B-3

User Parameter Pass Through

Disable

B-4

Beep After good Decode

Enable

B-5

Beeper Tone

Medium

B-6

Beeper Volume

High

B-7

Beeper Duration

Medium

B-8

Suppress Power-up Beeps

Do not suppress

B-9

Aim Brightness (Aiming LED)

High

B-10

Decode Aiming Pattern

Enable

B-11

Illumination Brightness (Illumination LED)

B-12

Decoding Illumination

Enable

B-13

Decode Blinks

Disable

B-14

Decode Blink Duration

Timeout Between

Decodes, Different

Symbols value

B-15

Trigger Modes

Level

B-16

Power Mode

Low Power

B-18

Time Delay to Low Power Mode

1.0 Sec

B-19

Picklist Mode

Disabled Always

B-20

Decode Session Timeout

9.9 Sec

B-21

Timeout Between Decodes, Same Symbol

0.6 Sec

B-22

Timeout Between Decodes Different Symbol

0.2 Sec

B-23

Continuous Barcode Read

Disable

B-24

Unique Barcode Reporting

Disable

B-25

Low Light motion Detection Assist

Disable

B-26

Presentation Mode Field of View

Medium Field of View

B-27

Fuzzy 1D Processing

Enable

B-28

Mirrored Image

Disable

B-29

Mobile Phone/Display Mode

Disable

B-30

A-2

Validate Concatenated Parameter Bar Codes

Disable

B-31

PDF Prioritization

Disable

B-32

PDF Prioritization Timeout

200 ms

B-33

Miscellaneous Scanning Parameters

Transmit Code ID Character

None

B-34

Prefix Values

<CR>

B-35

Suffix Value 1

Suffix Value 2

<CR>

B-35

Scan Data Transmission Format

Data as is

B-36

Transmit “No Read” Message

Disable

B-38

Report Version

B-39

Report Decoder Manufacturing Information

B-39

Report Scan Engine Manufacturing Information

B-39

A-3

Barcode Parameter Default

Parameter

Value

Page

Disable All Code Types

N/A

C-1

JAN (UPC/EAN)

UPC-A

Enable

C-2

UPC-E

Enable

C-2

UPC-E1

Disable

C-3

EAN-8/JAN8

Enable

C-3

EAN-13/JAN13

Enable

C-4

Bookland EAN

Disable

C-4

Bookland ISBN Format

ISBN-10

C-5

Decode UPC/EAN/JAN Supplementals

Ignore

C-6

User-Programmable Supplementals

Supplemental 1

Supplemental 2

N/A

F1h 43h

F1h 44h

C-10

UPC/EAN Supplemental Redundancy

C-11

UPC/EAN/JAN Supplemental AIM ID Format

Combined

C-12

Transmit UPC-A Check Digit

Enable

C-13

Transmit UPC-E Check Digit

Enable

C-13

Transmit UPC-E1 Check Digit

Enable

C-14

UPC-A Preamble

System Character

C-15

UPC-E Preamble

System Character

C-16

UPC-E1 Preamble

System Character

C-17

Convert UPC-E to UPC-A

Disable

C-18

Convert UPC-E1 to UPC-A

Disable

C-18

EAN-8/JAN-8 Extend

Disable

C-19

UCC Coupon Extend Code

Disable

C-19

Coupon Report

New Coupon Symbols

C-20

ISSN EAN

Disable

C-21

Code 128

Enable

C-22

Set Length(s) for Code128

Any Length

C-22

Enable/Disable GS1-128 (Formerly

UCC/EAN-128)

Enable

C-24

Enable/Disable ISBT128

Enable

C-25

A-4

ISBT Concatenation

Disable

C-26

Check ISBT Table

Enable

C-27

ISBT Concatenation Redundancy

C-27

Code 39

Enable/Disable Code39

Enable

C-28

Enable/Disable Trioptic Code39

Disable

C-28

Convert Code39 to Code32

Disable

C-29

Code32 Prefix

Disable

C-29

Set Length(s) for Code39

Length Within

Range: 2 to 55

C-30

Code39 Check Digit Verification

Disable

C-32

Transmit Code39 Check Digit

Disable

C-32

Code39 Full ASCII Conversion

Disable

C-33

Code 93

Enable/Disable Code 93

Disable

C-34

Set Length(s) for Code93

Length Within

Range: 4 to 55

C-35

Code 11

Enable/Disable Code11

Disable

C-37

Set Length(s) for Code11

Length Within

Range: 4 to 55

C-38

Code11 Check Digit Verification

Disable

C-40

Transmit Code11 Check Digit(s)

Disable

C-41

Interleaved 2 of 5 (ITF)

Enable/Disable Interleaved 2 of 5 (ITF)

Disable

C-42

Set Lengths for Interleaved 2 of 5

1 Length;

Length = 14

C-43

I 2 of 5 Check Digit Verification

Disable

C-45

Transmit I 2 of 5 Check Digit

Disable

C-46

Convert I 2 of 5 to EAN-13

Disable

C-47

I 2 of 5 Security Level

C-48

Discrete 2 of 5 (DTF)

Enable/Disable Discrete 2 of 5

Disable

C-50

Set Lengths for Discrete 2 of 5

1 Length;

Length = 12;

C-51

A-5

Codabar (NW-7)

Enable/Disable Codabar

Disable

C-53

Set Lengths for Codabar

Length Within

Range: 5 to 55

C-54

CLSI Editing

Disable

C-56

NOTIS Editing

Disable

C-56

Codabar Upper or Lower Case Start/Stop

Characters Detection

Upper Case

C-57

MSI

Enable/Disable MSI

Disable

C-58

Set Lengths for MSI

6-55

C-59

MSI Check Digit

One

C-61

Transmit MSI Check Digit(s)

Disable

C-61

MSI Check Digit Algorithm

Mod 10/Mod 10

C-62

Chinese 2 of 5

Enable/Disable Chinese 2 of 5

Disable

C-63

Matrix 2 of 5

Enable/Disable Matrix 2 of 5

Disable

C-64

Set Lengths for Matrix 2 of 5

Length;

Length = 14

C-65

Matrix 2 of 5 Check Digit

Disable

C-67

Transmit Matrix 2 of 5 Check Digit

Disable

C-67

Korean 3 of 5

Enable/Disable Korean 3 of 5

Disable

C-68

Inverse 1D

Regular

C-69

Postal Code

US Postnet

Disable

C-70

US Planet

Disable

C-70

Transmit US Postal Check Digit

Enable

C-71

UK Postal

Disable

C-72

Transmit UK Postal Check Digit

Enable

C-72

Japan Postal

Disable

C-73

Australia Post

Disable

C-73

Australia Post Format

Autodiscriminate

C-74

A-6

Netherlands KIX Code

Disable

C-75

USPS 4CB/One Code/Intelligent Mail

Disable

C-75

UPU FICS Postal

Disable

C-76

GS1 DataBar

GS1Databar

(Omnidirectional/Truncated/Stacked

/Stacked Omnidirectional)

Enable

C-77

GS1 Databar Limited

Disable

C-78

GS1 Databar Limited Security Level

C-79

GS1 Databar Expanded

(Expanded/Expanded Stacked)

Enable

C-80

Convert GS1 Databar to JAN (UPC/EAN)

Disable

C-80

Composite

Composite CC-C

Disable

C-81

Composite CC-A/B

Disable

C-81

Composite TLC-39

Disable

C-82

UPC Composite Mode

UPC Always Linked

C-83

Composite Beep Mode

Beep As Each Code

Type is Decoded

C-84

GS1-128 Emulation Mode for UCC/EAN

Composite Codes

Disable

C-84

2D Symbologies

Enable/Disable PDF417

Enable

C-85

Enable/Disable MicroPDF417

Disable

C-85

Code 128 Emulation

Disable

C-86

Data Matrix

Enable

C-87

Data Matrix Inverse

Regular

C-87

Decode Mirror Images (Data Matrix Only)

Auto

C-88

Maxicode

Disable

C-89

QR Code

Enable

C-89

QR Inverse

Regular

C-90

MicroQR

Enable

C-90

Aztec

Enable

C-91

Aztec Inverse

Inverse Autodetect

C-91

Han Xin

Disable

C-92

A-7

Han Xin Inverse

Regular

C-92

Redundancy Level

C-93

Security Level (UPC/EAN and Code 39)

C-95

Intercharacter Gap Size

Normal

C-97

Macro PDF

Macro PDF Transmit/Decode Mode Symbols

Passthrough Mode

C-98

Transmit Macro PDF Control Header

Enable

C-98

Escape Characters

None

C-99

Flush Macro PDF Buffer

C-99

Abort Macro Macro PDF Entry

C-99

Appendix

ASCII Character Sets

Z-1

Numeric Bar Codes

Z-6

Symbol Code Identifiers

Z-8

AIM Code Identifiers

Z-9

Modifier Characters

Z-10

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Lector de código de barras de AsReader

AsReader

AsReader ASR-L251G Series Manual de usuario

AsReader

AsReader ASR-010D Manual de usuario

AsReader

AsReader ASR-A23D Manual de usuario

AsReader

AsReader ASR-P35U-01 Manual de usuario

AsReader

AsReader ASR-010D Manual de usuario

AsReader

AsReader ASR-R202G Series Manual de usuario

AsReader

AsReader ASR-L70D Manual de usuario

AsReader

AsReader ASR-R202G Series Manual de usuario

AsReader

AsReader ASR-020D Manual de usuario

AsReader

AsReader ASR-023B Manual de usuario

AsReader

AsReader ASR-0230D Manual de usuario

AsReader

AsReader ASR-A24D Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario