Asko WS90CNTHJ Manual de usuario

Instructions for use

Cooker hood

CW4930G / WS90CNTHJ

CW41230G / WS12CNTHJ

CI41230G / ES12CNTIJ

EN Instructions for use EN 3 - EN 14

Pictograms used

Important information

Tipp

EN 3

CONTENTS

Your cooker hood

Introduction 4

Use

Description 5

Operation 6

Cleaning filters 8

Maintenance

Cleaning 9

Lighting 11

Technical specifications

Appendix

Disposal 14

EN 4

Introduction

On reading these user manuals you will soon become familiar with

the features of this appliance. Please read the appliance’s safety and

maintenance instructions.

Please retain the operating and installation instructions as these may be

useful for future reference.

Please read the separate safety instructions

prior to use.

YOUR COOKER HOOD

EN 5

USE

Description

1. Switching on/off and dimming the lighting

2. Reducing air extraction capacity and switching off

3. Cleaning filter indicator

4. Proximity sensor

5. Display status

6. Proximity sensor

7. Switching on and increasing air extraction capacity

8. Timer function indicator

1 2 3 4 5 6 7 8

EN 6

USE

Operation

Switching extraction on and off

• Press the ‘+’ key.

The cooker hood will switch on at the lowest setting.

• Press the ‘+’ key again to set a higher extraction setting. Press and

hold the ‘+’ key for 2 seconds to select the highest setting (boost)

(see switching on boost setting).

The extraction setting can be set between speeds level 1 to 5 or 9.

• Press the ‘-’ key to select a lower setting.

• If the extraction setting is set at 1, you can switch off the cooker

hood by quickly pressing and releasing the ‘-’ key.

• To switch off the cooker hood from whatever setting press and hold

the ‘-’ key for at least 2 seconds.

Alter the number of speed-settings

You can choose between 9 speed-settings (default) or 5 speed-settings.

• Press and hold the ‘-’ key and ‘+’ key for at least 5 seconds.

This selects the 5 speed-setting option. Press and hold the ‘-’ key

and ‘+’ key again for at least 5 seconds to select the 9 speed-

setting option.

Switching on recirculation

• Simultaneously press and hold the timer key and the lighting key

until the filter indicator flashes 3 times.

The carbon filter indicator is activated.

Switching off recirculation

• Simultaneously press and hold the timer key and the lighting key

until the filter indicator lights up.

Switching the lighting on and off

• Quickly press and release the lighting key.

The light switches on at maximum strength.

• Press and hold the lighting key to set the lighting strength.

The lighting changes from maximum to minimum strength and

vice versa.

• To turn off the light, quickly press and release the lighting key while

the light is on.

EN 7

Changing the colour temperature

Choose the temperature colour of the light from warm to cold.

• Press and hold the lighting key. Press the ‘+’ key to make the light

‘colder’ or press the ‘-’ key to make the light ‘warmer’.

Switch on boost setting:

• Press and hold the ‘+’ key for approximately 2 seconds.

The boost setting (setting ‘b’ or 7,8,9) is switched on for 10 minutes.

The display will flash during this period. The original extraction setting

will be reactivated after this period.

• Quickly press and release the ‘-’ key to switch off the boost setting.

Switching on the timer

• Press the timer key.

The timer indicator will start to blink.

The cooker hood will switch off automatically after 10 minutes.

• Switch off the timer function by pressing a random key (except the

one for lighting).

Note!

If the boost setting has been selected you cannot activate the timer

function.

Clean Air function

The Clean Air function allows you to freshen the air in your kitchen for a

maximum of 24 hours at level 1.

• Switch off the cooker hood.

• Press and hold the timer key for approximately 3 seconds.

The cooker hood will switch on automatically for 10 minutes every

hour at the lowest speed setting. During extraction the display will

show a fast rotating ‘snake’. When the hood switches off after

10 minutes, the display will show a slow rotating ‘snake’ until the

hood switches on again after 50 minutes.

• Switch off the Clean Air function in the meantime by pressing a

random key (except the one for lighting).

USE

EN 8

Active mode

• The proximity sensor detects a user standing in front of the hood

and will illuminate the icons. After 3 seconds the lighting will

automatically switch on.

Disable the active mode

• Simultaneously press the ‘+’ and ‘timer’ key for 3 seconds.

The active mode is disabled. The display show an static ‘U’.

Enable the active

• Simultaneously press the ‘+’ and timer key for 3 seconds.

The active mode is enabled. The display show 3 times a

blinking ‘U’.

Cleaning filters

Saturation grease and carbon filters

The filters should be replaced or cleaned when the grease filter

indicator or the carbon filter indicator are lit. See chapter ‘Maintenance’.

Grease filter

The filter indicator will light up after 30 operating hours.

• The grease filters should then be cleaned.

• Reset the memory by pressing and holding the ‘-’ key until the filter

indicator stops flashing.

Carbon filter

The filter indicator will flash after 120 operating hours.

• The carbon filter should then be cleaned or replaced.

• Reset the memory by simultaneously pressing and holding the ‘-’

and ‘+’ keys until the filter indicator stops flashing.

USE

EN 9

Cleaning

Important!

For all maintenance first switch off the mains power to the cooker hood

by pulling the plug out of the socket or by turning off the home's master

switch. The hood needs to be cleaned regularly, both inside as well as

outside (at least in the same frequency as the grease filter cleaning).

Do not use abrasive cleaning products. Do not use alcohol!

Important!

If the instructions regarding cleaning the appliance or replacing the

filters are not followed, this can cause a fire. These instructions should

be followed! The manufacturer is not liable for damage to the hood

or fire damage resulting from incompetent maintenance or from

non-adherence to the above safety instructions.

Cooker hood

Clean the cooker hood with soapy water and a soft cloth.

Then wash off with clean water. Do not use aggressive cleaning agents

such as caustic soda. The cooker hood finish stays in good condition if

it is buffed periodically following the application of wax.

Stainless steel cooker hoods

Do not use scouring pads or other abrasive cleaners on stainless steel

cooker hoods. Finish with a non-abrasive, non-polishing agent and buff

the stainless steel in the direction of the grain.

Metal grease filters

Metal grease filters should be cleaned once a month (or when indicated

by the filter cleaning indicator – if present on the model) using a neutral

cleaning agent, either by hand or in the dishwasher on a short, low-

temperature program. Place the grease filters with the openings facing

downwards in the dishwasher so the water can drain out of the filter.

Aluminium grease filters become dull as a result of dishwasher cleaning

agents. This is normal and does not effect the working.

MAINTENANCE

EN 10

Removing cassette filter

1 Switch off the motor and lighting.

2 Push in the locking lugs at the front behind the glass plate and

pull the glass plate carefully out of the seal. Tilt the glass plate

downwards.

3 Open the filter’s access hatch.

4 Remove the filter from the hood.

Cleaning

The filters can be cleaned in the dishwasher. Allow the filters to drain

well before replacing.

The filters can also be cleaned by hand.

Clean the filters in soapy water with washing up liquid and rinse. Allow

the filters to drain well. Consult chapter ‘Cleaning’. The underside of

the cooker hood can be cleaned with a mild cleaning agent and a damp

cloth. Dry off with a paper towel.

Replacing cassette filter

The filter should be placed with the locking mechanism on the front.

Open the filter access hatch. The notches at the front of the filter will then

slot in. Hold the access hatch in this position when placing the filters.

1 Slot the notches at the back of the filter in the specially designed

opening of the cooker hood.

2 Tilt the filter upwards.

3 Release the filter access hatch. The notches at the back of the

filter will extend outwards and slot into the specially designed

openings of the cooker hood.

The filter is now in position again.

4 Press the glass plate firmly in the seal again (you will hear a click).

The glass plate can be removed for cleaning. Always remove the

glass plate with 2 persons (due to its weight)!

MAINTENANCE

Este manual sirve para los siguientes modelos

Otros manuales de Campana de ventilación de Asko

Manuales populares de Campana de ventilación de otras marcas

emmeti

emmeti RECUPA MED A-140 Guía

Nibe

Nibe F135 Manual de usuario

Kuppersberg

Kuppersberg INTRO 60 Instrucciones de instalación y mantenimiento

Zephyr

Zephyr Spruce AK9834BS Guía de instalación

Hisense

Hisense MH6INBG Manual de usuario

Miele

Miele DA 1255 Manual de usuario

Broan

Broan 46000 Manual de usuario

GE Profile PV977 Instrucciones originales

FALMEC

FALMEC FFRIA24W5FS Manual de usuario

Whirlpool

Whirlpool RH2600XL-1 SERIES Manual de usuario

Küppersbusch

Küppersbusch DX ISLA Manual de usuario

ETNA

ETNA AV360RVS Manual de usuario

JUNO

JUNO JDF603E6 Manual de usuario

Miele

Miele DA 6708 D Manual de usuario

Tricity Bendix

Tricity Bendix LE 150 Manual

AEG

AEG X68163BV1 Manual de usuario

AEG

AEG 125 D Manual de usuario

Smeg

Smeg KSEV97X Manual de usuario