Ascon tecnologic KM Series Instrucciones de funcionamiento

Tecnologic ‘KR’ Series

UK Quick Programming Guide

This guide should be used alongside the full engineering manual, appropriate to the instrument being

used, where more detailed information can be found (download manual from www.t-uk.co.uk).

Programming the Instrument

Tecnologic controllers are supplied with default programmable settings that may be suitable for your

application. However we recommend that you go through the programming process, as incorrect

programming could compromise its performance.

There are four possible ways of programming the KR range of controllers:

1. Quick setting - using 8 numbers derived from a parameter option list shown later in this

document. If the options you require are not shown you will need to use either the basic

or full menu options.

2. Basic menu – Most standard options can be programmed here in a simple sequential

parameter list.

3. Full menu - All programming options are here, split into sub-menus.

4. Via software or memory KEY015-E – Key plugs into controller and PC via USB.

Key

U button is used for navigation between

menus. Holding down for 1 second will take

you back one step. Holding down for 2

seconds will take you out of configuration.

P button used for entering or moving to the

next parameter.

Up & down buttons used for increasing or

decreasing values.

Programming level pass

numbers

300

- Quick setting using a 2 x 4 digit code.

- Basic menu with 10 second time out

function.

– Full menu

Note: To reset instrument to factory default

settings, press P for 5 seconds and dial in -481.

Press Pto confirm





Unit 1 Farnborough Business Centre, Eelmoor Road, Farnborough, GU14 7XA

T: 01252 377600 F: 01252 377601 E: sales@tecnologicuk.co.uk

Quick Setting Configuration Codes

The controller configuration (Input type, Control mode Alarms and Auxiliary functions) can be made

by entering two 4-digit codes. You can work out the 2 relevant configuration codes using the tables

below.

To work out code 1

To work out code 2

Cod1

Control Mode

OP1

ON/OFF heating = H

AL1

AL2

AL3

AL1

AL2

ON/OFF cooling = C

AL1

AL2

AL3

AL1

AL2

ON/OFF with neutral

zone (H/C)

AL2

AL3

AL1

AL2

AL3

AL2

AL1

AL2

PID heating =H

AL1

AL2

AL3

AL1

AL2

PID cooling =C

AL1

AL2

AL3

AL1

AL2

PID double action (H/C)

AL2

AL3

AL1

AL2

AL3

AL2

AL1

AL2

Input Type & Range

TC J

-50...+1000°C

TC K

-50...+1370°C

TC S

-50...+1760°C

TC R

-50...+1760°C

TC T

-70...+400°C

Infrared J

-50...+785°C

Infrared K

-50...+785°C

PT100 / PTC KTY81-121

-200... +850°C/ -55...+150°C

PT1000 / NTC 103-AT2

-200... +850°C/ -55...+110°C

Linear 0...60mV

Liner 12...60mV

Linear 0...20mA (this selection forces out 4=TX)

Linear 4...20mA (this selection forces Out 4=TX)

Linear 0...5V

Linear 1...5V

Linear 0...10V

Linear 2...10V

TC J

-58...+1832°F

TC K

-58...+2498°F

TC S

-58...3200°F

TC R

-58..+3200°F

TC T

-94..+752°F

Infrared J

-58..+1445°F

Infrared K

-58..+1445°F

PT100 / PTC KTY81-121

-328...+1562°F/ -67...+302°F

PT1000 / NTC 103-AT2

-328...+1562°F/ -58...+230°F

Cod2

Alarm 3

Alarm 2

Alarm 1

Not used

Sensor break

Absolute

High

Low

Absolute High/Low

External High/Low

Internal High/ Low

Deviation

Deviation High

Deviation Low

Band

External Band

Internal Band

Auxiliary functions activation

None

Wattmeter (instantaneous power

expressed in W)

Wattmeter (energy expressed in Wh)

Absolute worked time (expressed in days)

Absolute worked time (expressed in hrs)

Entering the codes

Press ‘P’ and then enter the pass code, 300.

Press ‘P’ again. You can now enter in code 1.

Press ‘P’ and enter code 2 in.

The screen will then flash is code is accepted or

not.

Navigating the basic level programming guide

This is a blueprint guide for changing all the parameter settings on the instrument within the 81 basic

menu.

Note: Some parameters will disappear and/or additional parameters will appear depending on

settings selected. If the advanced menu is required use the 40 pass code & select appropriate menu

using the ‘U’ key. Please refer to the main manual.

Start/ Configure.

Power up unit. tEST will flash

Press & hold .

Dial in ‘81’ & press Pto confirm.



With power to unit press Pfor 5

seconds.

‘Pass’ is displayed along with ‘0’

Use and arrow to

select required setting

within chosen parameter.

Press Pto confirm.





Unit then accepts the chosen

setting and moves on to next

parameter in menu. (Repeat

above for all required parameters)

To exit programming press and

hold Uto return to displayed

temperature.

To skip a parameter

press Pto move onto

next one.

Unit will display first parameter in

menu, i.e. SEnS

81 Basic parameter menu

Display

Parameter name/

description

Manual

ref.

SEnS

Sensor/ input type

[1]

Decimal point position

[2]

unit

Engineering Unit

[5]

o1F

Output function 1

[13]

o2F

Output function 2

[18]

o3F

Output function 3

[21]

o4F

Output function 4

[24]

cont

Control type

[55]

Auto

Auto tuning for PID

parameters

[56]

Proportional band value

(°C)

[61]

Integral time

[62]

Derivative time

[63]

Fuoc

Fuzzy overshoot control

[64]

tcH

Heating output cycle

time

[65]

SPLL

Min. adjustable set

point value

[76]

SPHL

Max. adjustable set

point value

[77]

Control set point

[78]

AL1t

Alarm 1 type/function

[27]

AL2t

Alarm 2 type/function

[35]

AL3t

Alarm 3 type/function

[43]

di.cL

Display colour

[122]

io4.F

Input/ Output 4 function

[9]

Unit 1 Farnborough Business Centre, Eelmoor Road, Farnborough, GU14 7XA

T: 01252 377600 F: 01252 377601 E: sales@tecnologicuk.co.uk

Otros manuales para KM Series

Este manual sirve para los siguientes modelos

Otros manuales de Controladores de Ascon tecnologic

Ascon tecnologic

Ascon tecnologic KX6 Series Manual de instalación y operación

Ascon tecnologic

Ascon tecnologic K49 Manual de instalación y operación

Ascon tecnologic

Ascon tecnologic XS Series Manual de usuario

Ascon tecnologic

Ascon tecnologic R38 Manual de usuario

Ascon tecnologic

Ascon tecnologic KM3-L Manual de instalación y operación

Ascon tecnologic

Ascon tecnologic TLB 55 Manual de usuario

Ascon tecnologic

Ascon tecnologic KM1E Manual de usuario

Ascon tecnologic

Ascon tecnologic K48 Manual de instalación y operación

Ascon tecnologic

Ascon tecnologic Y39W Manual de usuario

Ascon tecnologic

Ascon tecnologic TLY25 Manual de usuario

Ascon tecnologic

Ascon tecnologic K32L Manual de instalación y operación

Ascon tecnologic

Ascon tecnologic KR1E Manual de usuario

Ascon tecnologic

Ascon tecnologic Y39SE Manual de usuario

Ascon tecnologic

Ascon tecnologic Z31Y Manual de usuario

Ascon tecnologic

Ascon tecnologic TLY26 Manual de usuario

Ascon tecnologic

Ascon tecnologic B05 Manual de usuario

Ascon tecnologic

Ascon tecnologic X5 Series Manual de usuario

Ascon tecnologic

Ascon tecnologic K 1E Series Manual de instalación y operación

Ascon tecnologic

Ascon tecnologic X33H Manual de usuario

Ascon tecnologic

Ascon tecnologic TLK94-A Manual de usuario

Ascon tecnologic

Ascon tecnologic K 5P Series Manual de instalación y operación

Ascon tecnologic

Ascon tecnologic Y39 Manual de usuario

Ascon tecnologic

Ascon tecnologic TLK41 Manual de usuario

Ascon tecnologic

Ascon tecnologic e31 Series Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario