Aruba IAP-274 Manual de usuario

IAP-270 Series Outdoor Access Point

Installation Guide

0511605-04 |December 2017 1

The Aruba IAP-274 and IAP-275 are environmentally hardened, outdoor rated, dual-radio IEEE 802.11ac

wireless access points. These access points use MIMO (Multiple-in, Multiple-out) technology and other

high-throughput mode techniques to deliver high-performance, 802.11ac 2.4 GHz and 5 GHz functionality

while simultaneously supporting existing 802.11a/b/g/n wireless services.

IAP-270 Series Operations

Wireless transceiver

Wireless access point (IEEE 802.11 a/b/g/n/ac)

Wireless air monitor (IEEE 802.11 a/b/g/n/ac)

Protocol-independent networking functionality

Compatibility with IEEE 802.3at PoE

Guide Overview

"IAP-270 Series Hardware Overview" on page3 provides a detailed hardware overview of the IAP-274

and IAP-275.

"Before You Begin" on page7 provides key questions to ask and items to consider when deploying an

outdoor wireless network.

"Installing the AP" on page8 describes the multi-step process for a successful installation and

deployment of the IAP-274 and IAP-275.

"Safety and Regulatory Compliance" on page14 provides an overview of safety and regulatory

compliance information.

Package Contents

IAP-274 or IAP-275 Access Point

Cable Glands x2

Copper Lug x1

M4x6 Screw x1

USB Console Cable

Aruba Instant Quick Start Guide

Installation Guide (this document)

The IAP-270 Series requires Aruba Instant 4.1 or later.

The weatherproof caps for Ethernet, Console, and power interfaces are connected to the AP, not loose in the

package.

2IAP-270 Series Outdoor Access Point | Installation Guide

Mounting kits for use with the IAP-270 Series access points are sold separately. Contact your Aruba sales

representative for details.

Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including

the original packing materials. Use these materials to repack and return the unit to the supplier if needed.

IAP-270 Series Outdoor Access Point | Installation Guide 3

IAP-270 Series Hardware Overview

Figure 1 IAP-274 Front View (Aesthetic Cover Removed)

Figure 2 IAP-275 Front View

LED

The IAP-270 Series is equipped with one LED that indicates the system status of the AP.

System LED

The antenna connectors of IAP-274 are covered by an aesthetic cover in the package. The aesthetic cover can be

removed when necessary.

System LED

4IAP-270 Series Outdoor Access Point | Installation Guide

Table 1 IAP-270 Series LED Meanings during Boot Up

Table 2 IAP-270 Series LED Meanings during Operation

Figure 3 IAP-274 Rear View

LED Color/State Meaning

System LED Off No power to AP

Red Initial power-up

Green - Flashing AP booting

Green - Steady AP ready and 1000Mbps Ethernet link established. The LED turns

off after 1200 seconds

Green - Yellow, 6 seconds

period AP ready and 10/100Mbps Ethernet link established. The LED

turns off after 1200 seconds

LED Color/State Meaning

System LED Solid Red General fault

One blink off every 3

seconds Radio 0 fault (5 GHz)

Two quick blink off 0.5

seconds apart cycled every

3 seconds

Radio 1 fault (2.4GHz)

AC Power Interface

LAN Port

WAN Port

Grounding Point

USB Console Port and Reset button

IAP-270 Series Outdoor Access Point | Installation Guide 5

Figure 4 IAP-275 Rear View

USB Console Port

The USB Micro-B console port allows you to connect the AP to a terminal or a laptop for direct local

management. Use the included USB console cable to connect the AP. You can download the necessary

driver for USB-UART adapter from support.arubanetworks.com under the Tools & Resources tab.

Use the following setting to access the terminal:

Ethernet Ports

IAP-270 Series is equipped with two10/100/1000Base-T (RJ-45) Gigabit Ethernet ports (WAN and LAN port)

for wired network connectivity. The WAN port supports 802.3at Power over Ethernet (PoE), accepting 48

VDC (nominal) as a standard defined Powered Device (PD) from a Power Sourcing Equipment (PSE) such

as a PoE midspan injector.

These ports have RJ-45 female connectors with the pin-outs shown in Figure 5.

Figure 5 Gigabit Ethernet Port Pin-Out

Reset Button

The reset button can be used to return the AP to factory default settings. To reset the AP:

Table 3 Console Settings

Baud Rate Data Bits Parity Stop Bits Flow Control

9600 8 None 1 None

AC Power Interface

LAN Port

WAN Port

Grounding Point

USB Console Port and Reset button

1000Base-T Gigabit

Ethernet Port

RJ-45 Female

Pin-Out

Signal Name

BI_DC+

BI_DC-

BI_DD+

BI_DD-

BI_DA+

BI_DA-

BI_DB+

BI_DB-

Function

Bi-directional pair +C, POE Positive

Bi-directional pair -C, POE Positive

Bi-directional pair +D, POE Negative

Bi-directional pair -D, POE Negative

Bi-directional pair +A, POE Negative

Bi-directional pair -A, POE Negative

Bi-directional pair +B, POE Positive

Bi-directional pair -B, POE Positive

6IAP-270 Series Outdoor Access Point | Installation Guide

1. Power off the AP.

2. Press and hold the reset button using a small, narrow object, such as a paperclip.

3. Power-on the AP without releasing the reset button. The system LED will flash within 5 seconds.

4. Release the reset button.

The system LED will flash again within 15 seconds indicating that the reset is completed. The AP will now

continue to boot with the factory default settings.

AC Power Interface

The IAP-270 Series is capable of AC power in the range of 100 - 240 VAC. The power cord or power

connector kit is sold separately.

Grounding Point

Always remember to protect the AP by installing grounding lines. The ground connection must be complete

before connecting power to the AP enclosure.

Figure 6 IAP-274 and IAP-275 Top View

At the top of the IAP-270 Series, the solar shield with the mounting holder is fixed onto the AP before

shipping from the factory.

Figure 7 IAP-274 Bottom View

Solar Shield

Mounting Holder

With Aesthetic Cover Aesthetic Cover Removed

IAP-270 Series Outdoor Access Point | Installation Guide 7

Figure 8 IAP-275 Bottom View

External Antenna Connectors

The IAP-274 is equipped with six N-type female connectors.for external antenna. The connectors are

labeled 2G0, 2G1, 2G2, 5G0, 5G1 and 5G2, and correspond to 2.4/5Ghz radio chains 0,1, and 2.

Air Vent

The bottom of the IAP-270 Series has an air vent to balance the pressure and humidity inside and outside

the AP. It also allows air exchange between the AP and the environment in a controlled way that doesn’t

allow water to get into the AP.

Before You Begin

Air Vent

Please install the external antennas according to the manufacturer’s instruction and connect the antennas to the N-

type female antenna connectors on the IAP-274 access point.

External antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or other

Aruba-certified technician, using manufacturer-approved antennas only.

The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the

regulatory limit set by the host country/domain.

Installers are required to record the antenna gain for this device in the system management software.

Les antennes externes pour cet appareil doivent être installées par un professionnel de la mobilité certifié Aruba

(ACMP) ou un autre technicien certifié Aruba, en utilisant uniquement des antennes approuvées par le fabricant.

Les niveaux équivalents de puissance à rayonnement isotrope (EIRP) pour tous les périphériques d'antenne

externe ne doivent pas dépasser la limite réglementaire définie par le pays hôte / domaine.

Les installateurs doivent enregistrer le gain d'antenne pour cet appareil dans le logiciel de gestion du système.

FCC Statement: Improper termination of access points installed in the United States (non-US model Regulatory

Domain model/s) will be in violation of the FCC grant of equipment authorization. Any such willful or intentional

violation may result in a requirement by the FCC for immediate termination of operation and may be subject to

forfeiture (47 CFR 1.80).

8IAP-270 Series Outdoor Access Point | Installation Guide

Identifying Specific Installation Locations

You can mount the IAP-270 Series access point on a wall or pole. Use the AP placement map generated by

Aruba’s RF Plan software application to determine the proper installation location(s). Each location should

be as close as possible to the center of the intended coverage area and should be free from obstructions or

obvious sources of interference. These RF absorbers/reflectors/interference sources will impact RF

propagation and should have been accounted for during the planning phase and adjusted for in RF plan.

Identifying Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the field during the

installation phase is critical. Make sure that these sources are taken into consideration when you attach an

AP to its fixed location. Examples of sources that degrade RF performance include:

Cement and brick

Objects that contain water

Metal

Microwave ovens

Wireless phones and headsets

Installing the AP

EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the Aruba Instant User

Guide for details on restrictions.

Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous

referrer au Aruba Instant User Guide pour les details des restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich

Einschränkungen finden Sie im Aruba Instant User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla Aruba Instant User Guide

per avere informazioni detagliate sulle restrizioni.

Aruba Networks, Inc. in compliance with governmental requirements, has designed the IAP-270 Series such that

only authorized network administrators can change configuration settings. For more information about AP

configuration, refer to the Aruba Instant Quick Start Guide and Aruba Instant User Guide.

Access points are radio transmission devices and as such are subject to governmental regulation. Network

administrators responsible for the configuration and operation of access points must comply with local broadcast

regulations. Specifically, access points must use channel assignments appropriate to the location in which the

access point will be used.

Service to all Aruba products should be performed by trained service personnel only.

IAP-270 Series Outdoor Access Point | Installation Guide 9

Using the Mounting Kits

The IAP-270 Series can be installed on a wall or attached to a pole by using mounting kits:

Grounding the AP

The grounding must be completed before powering up the AP. The grounding wire should be #8 AWG.

1. Peel the cover of one end of the grounding wire and place the bare grounding wire into the included

copper lug, and press firmly with the crimping pliers.

2. Fasten the copper lug to the grounding hole on the AP with the included M4 x6 screw as shown in Figure

Figure 9 Grounding the AP

Connecting the Ethernet Cable

To connect the Ethernet cable to the AP, perform the following steps using the cable glands that ships with

your AP.

Table 4 Applicable Mounting Kits for IAP-270 Series

Part Number Description

AP-270-MNT-V1 Long mounting kit for wall and vertical pole mounting, 300 mm from vertical mounting

asset.

AP-270-MNT-V2 Short mounting kit for wall and vertical pole mounting, 75 mm from vertical mounting

asset.

AP-270-MNT-H1 Mounting kit for hanging from inclined or horizontal structure.

The IAP-270 Series access point does not ship with any mounting kits. These mounting kits are available as

accessories.and must be ordered separately.

For installation instructions on AP-270-MNT-V1, AP-270-MNT-V2 and AP-270-MNT-H1, please refer to the AP-

270-MNT-V1 Installation Guide, AP-270-MNT-V2 Installation Guide and AP-270-MNT-H1 Installation Guide

respectively.

Failure to use the included Ethernet cable glands can lead to connectivity and POE issues.

10 IAP-270 Series Outdoor Access Point | Installation Guide

Figure 10 Installing a Cable Gland

1. Slide the sealing nut over the cable (without the RJ45 connector attached to the end).

2. Slide the clamping ring over the cable.

3. Using a crimping tool, attach the shielded RJ45 connector to the end of the cable.

4. Remove the weatherproof cap on the Ethernet port.

5. Insert the RJ45 connector to the Ethernet port.

6. Screw the clamping ring onto the Ethernet port.

7. Screw the sealing nut onto the clamping ring.

Connecting the Power Cable

The IAP-270 Series product offering offers two ways to connect the unit to AC power. Two power cord

variants are offered and a connector kit that allows the customer to assemble their own cable if the

standard offering does not meet deployment needs.

The applicable SKUs for these options are:

The cable is not included and must be purchased separately. Purchase a suitable UV-resistant, outdoor rated, CAT

5E or better RJ45 cable for use with the AP.

Sealing Nut Clamping Ring CAT 5E or Better Cable

Seals

The seals inside the clamping ring by factory default is applicable for cables with 5-8.5 mm diameter. In the cable

gland kit, another seals is provided for use with the cables with 7-10 mm diameter.

Installation and service of Aruba products should be performed by Professional Installers in a manner that is

consistent with the electrical code in force in the jurisdiction of deployment. In many countries this will require a

licensed electrician to perform this operation. In Japan, this is a Certified Electrician by Ministry of Economy, Trade,

and Industry.

The IAP-270 Series does not ship with any power cables. These are available as accessories and should be ordered

separately.

Table 5 SKUs for Powering Options

Part Number Description

PC-OD-AC-P-NA Weatherproof AC power cable(5m), North America version

PC-OD-AC-P-INT Weatherproof AC power cable(5m), International (EU) version

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Aruba

Aruba

Aruba 300 series Manual de usuario

Aruba

Aruba AP-80MB Manual de usuario

Aruba

Aruba Instant On AP12 Manual de usuario

Aruba

Aruba IAP-367 Manual de usuario

Aruba

Aruba AWS-100 Manual de usuario

Aruba

Aruba 303 Series Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

Aruba

Aruba AP-65WB Manual de usuario

Aruba

Aruba Instant On AP11D Manual de usuario

Aruba

Aruba 518 Series Manual de usuario

Aruba

Aruba AP-92 Manual de usuario

Aruba

Aruba 503H Manual de usuario

Aruba

Aruba IAP-303H Manual de usuario

Aruba

Aruba AP-103H Manual de usuario

Aruba

Aruba IAP-205H Manual de usuario

Aruba

Aruba AP-120 Series Manual de usuario

Aruba

Aruba IAP-228 Manual de usuario

Aruba

Aruba 210 Series Manual de usuario

Aruba

Aruba 580EX Series Manual de usuario

Aruba

Aruba AP-105 Manual de usuario

Aruba

Aruba 570 Series Manual de usuario

Aruba

Aruba 360 Series Manual de usuario

Aruba

Aruba AP-68P Manual de usuario

Aruba

Aruba AP-504 RW Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario

EnGenius

EnGenius EAP350 Manual de usuario