Aruba AP-318 Manual de usuario

Aruba 318 Series Wireless Access Point

Installation Guide

Rev 03 | February 2018 1

The Aruba 318 Series access points support IEEE 802.11ac Wave 2 standard, delivering high performance with

the MU-MIMO (Multi-User Multiple-Input, Multiple-Output) technology, while also supporting 802.11a/b/g/n

wireless services.

The 318 Series wireless access point provides the following capabilities:

IEEE802.11a/b/g/n/ac operation as a wireless access point

IEEE802.11a/b/g/n/ac operation as a wireless air monitor

IEEE802.11a/b/g/n/ac spectrum monitor

Compatibility with IEEE 802.3at PoE

Guide Overview

“Hardware Overview” on page2provides a detailed hardware overview of the 318 Series access points.

“Before You Begin” on page4provides key questions to ask and items to consider when deploying a wireless

network.

“Installing the AP” on page6describes the multi-step process for a successful installation and deployment of

the 318 Series access points.

“Safety and Regulatory Compliance” on page10 provides an overview of safety and regulatory compliance

information.

Package Contents

318 Series access point

Ethernet cable gland x1

USB console cable

Copper lug x1

M4 x 6 screw x1

Startup guide

Simplified Declaration of Conformity

The weatherproof caps for Ethernet and Console interfaces are connected to the access point, not loose in the

package.

Mounting kits for use with the 318 Series access points are sold separately. Contact your Aruba sales

representative for details.

Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton,

including the original packing materials. Use these materials to repack and return the unit to the supplier if

needed.

2Aruba 318 Series Wireless Access Point | Installation Guide

Hardware Overview

Figure 1 318 Series Front View

Figure 2 318 Series Bottom View

LED

The 318 Series access point is equipped with one LED that indicates the system status of the access point.

E0/POE

E1/SFP

Grounding Point

USB Console Port, Reset button and LED

CAUTION

External antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or other

Aruba-certified technician, using manufacturer-approved antennas only.

The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the

regulatory limit set by the host country/domain.

Installers are required to record the antenna gain for this device in the system management software. A list of

approved antennas can be found at: http://www.arubanetworks.com/assets/og/OG_AP-318Series.pdf.

Les antennes externes pour cet appareil doivent être installées par un professionnel de la mobilité certifié Aruba

(ACMP) ou un autre technicien certifié Aruba, en utilisant uniquement des antennes approuvées par le fabricant.

Les niveaux équivalents de puissance à rayonnement isotrope (EIRP) pour tous les périphériques d'antenne

externe ne doivent pas dépasser la limite réglementaire définie par le pays hôte / domaine.

Les installateurs doivent enregistrer le gain d'antenne pour cet appareil dans le logiciel de gestion du système.

Aruba 318 Series Wireless Access Point | Installation Guide 3

Table 1 318 Series LED Meanings during Boot Up

Table 2 318 Series LED Meanings during Operation

USB Console Port

The USB Micro-B console port allows you to connect the access point to a laptop or serial console for direct

management. Use the included USB console cable to connect the access point. You can download the necessary

driver for USB-UART adapter from support.arubanetworks.com under the Tools & Resources tab.

Use the following setting to access the terminal:

Reset Button

The reset button can be used to return the access point to factory default settings. To reset the access point:

1. Power off the access point.

2. Press and hold the reset button using a small, narrow object, such as a paper clip.

3. Power-on the access point without releasing the reset button. The system LED will flash within 5 seconds.

4. Release the reset button.

The system LED will flash again within 15 seconds indicating that the reset is completed. The access point will

now continue to boot with the factory default settings.

LED Color/State Meaning

System LED Off No power to AP

Red Initial power-up

Green - Flashing AP booting

Green - Steady AP ready and 1000Mbps Ethernet link established. The LED

turns off after 1200 seconds

Green - Yellow, 6 seconds

period AP ready and 10/100Mbps Ethernet link established. The LED

turns off after 1200 seconds

LED Color/State Meaning

System LED Solid Red General fault

One blink off every 3

seconds Radio 0 fault (5 GHz)

Two quick blink off 0.5

seconds apart cycled every

3 seconds

Radio 1 fault (2.4GHz)

You need a proper Allen wrench (8mm) to open the cover of the USB Console port.

Table 3 Console Settings

Baud Rate Data Bits Parity Stop Bits Flow Control

9600 8 None 1 None

4Aruba 318 Series Wireless Access Point | Installation Guide

Ethernet Port

318 Series access point is equipped with one 10/100/1000 Base-T auto-sensing MDI/MDX Ethernet port. This port

supports wired-network connectivity, in addition to Power over Ethernet (PoE) from IEEE 802.3at compliant

power sources.

This access point accepts 56V DC (802.3at) nominal as a standard powered device (PD) from a Power Sourcing

Equipment (PSE) such as a PoE midspan injector, or network infrastructure that supports PoE.

This port has an RJ-45 female connector with the pin-outs shown in Figure 3.

Figure 3 Gigabit Ethernet Port Pin-Out

Grounding Point

Always remember to protect the access point by installing grounding lines. The ground connection must be

complete before connecting power to the access point enclosure.

SFP Port

The 318 Series access point is equipped with one 1000 Base-X small form-factor pluggable (SFP) port for fiber-

optic network connections. The applicable SFP modules includes:

Aruba SFP-LX-EXT SFP module (part number: Q8N52A)

Aruba SFP-SX-EXT SFP module (part number Q8N53A)

The applicable SFP cable gland is Aruba CKIT-OD-SFP SFP cable gland (part number: Q8N54A). The SFP module

and cable gland are sold separately. Contact your Aruba sales representative for details.

Figure 4 318 Series Rear View

Before You Begin

1000Base-T Gigabit

Ethernet Port

RJ-45 Female

Pin-Out

Signal Name

BI_DC+

BI_DC-

BI_DD+

BI_DD-

BI_DA+

BI_DA-

BI_DB+

BI_DB-

Function

Bi-directional pair +C, POE Positive

Bi-directional pair -C, POE Positive

Bi-directional pair +D, POE Negative

Bi-directional pair -D, POE Negative

Bi-directional pair +A, POE Negative

Bi-directional pair -A, POE Negative

Bi-directional pair +B, POE Positive

Bi-directional pair -B, POE Positive

CAUTION

FCC Statement: Improper termination of access points installed in the United States configured to non-US

model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or

intentional violation may result in a requirement by the FCC for immediate termination of operation and may

be subject to forfeiture (47 CFR 1.80).

Aruba 318 Series Wireless Access Point | Installation Guide 5

Pre-Installation Network Requirements

After WLAN planning is complete and the appropriate products and their placement have been determined, the

Aruba controller(s) must be installed and initial setup performed before the Aruba access points are deployed.

For initial setup of the controller, refer to the ArubaOS Quick Start Guide for the software version installed on your

controller.

Pre-Installation Checklist

Before installing your access point, be sure that you have the items listed below:

CAT5E UTP cable or better

IEEE 802.3at compliant PoE source

For 318 Series access point running ArubaOS only:

Aruba controller provisioned on the network

Layer 2/3 network connectivity to your access point

One of the following network services:

Aruba Discovery Protocol (ADP)

DNS server with an “A” record

DHCP Server with vendor specific options

CAUTION

EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS/Instant

User Guide for details on restrictions.

Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous

referrer au ArubaOS/Instant User Guide pour les details des restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich

Einschränkungen finden Sie im ArubaOS/Instant User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS/Instant User

Guide per avere informazioni detagliate sulle restrizioni.

CAUTION

To meet regulatory restrictions, the access point must be professionally installed.

The instructions in this section are applicable to the 318 Series access points running ArubaOS only.

Aruba in compliance with governmental requirements, has designed the 318 Series such that only authorized

network administrators can change configuration settings. For more information about AP configuration, refer

to the ArubaOS Quick Start Guide and ArubaOS/Instant User Guide.

CAUTION

Access points are radio transmission devices and as such are subject to governmental regulation. Network

administrators responsible for the configuration and operation of access points must comply with local

broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in

which the access point will be used.

6Aruba 318 Series Wireless Access Point | Installation Guide

Verifying Pre-Installation Connectivity

Before you install access points in a network environment, make sure that the access points will be able to locate

and connect to the controller when they are powered on. Specifically, you must verify the following conditions:

When connected to the network, each access point is assigned a valid IP address.

Access points are able to locate the controller.

Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the controller.

Identifying Specific Installation Locations

Use the AP placement map generated by Aruba’s RF Plan software application to determine the proper

installation location(s). Each location should be as close as possible to the center of the intended coverage area

and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/

interference sources will impact RF propagation and should have been accounted for during the planning phase

and adjusted for in RF plan.

Identifying Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation

phase is critical. Make sure that these sources are taken into consideration when you attach an AP to its fixed

location. Examples of sources that degrade RF performance include:

Cement and brick

Objects that contain water

Metal

Microwave ovens

Wireless phones and headsets

Installing the AP

Using Mount Kits

The 318 Series access points can be installed on a wall or attached to a pole by using mount kits. The AP-220-

MNT-W1 Mount Kit is directly compatible, while the AP-270-MNT-V1, AP-270-MNT-V2, AP-270-MNT-H1 and AP-

270-MNT-H2 mount kit are compatible when the AP-270-MNT-ADP adapter is utilized.

The instructions in this section are applicable to the 318 Series access points running ArubaOS only.

Service to all Aruba products should be performed by trained service personnel only.

Table 4 Applicable Mount Kits for 318 Series Access Point

Part Number Description

JW046A AP-220-MNT-W1 flat surface wall/ceiling black AP basic flat surface mount kit

JW047A AP-220-MNT-W1W flat surface wall/ceiling white AP basic flat surface mount kit

JW056A AP-270-MNT-ADP AP-228 to AP-270-MNT-XX Outdoor Mount Adapter

JW052A AP-270-MNT-V1 long mount kit for wall and vertical pole mounting, 300 mm from

vertical mounting asset.

Aruba 318 Series Wireless Access Point | Installation Guide 7

Grounding the Access Point

The grounding must be completed before powering up the access point. The grounding wire should be #8 AWG.

1. Peel the cover of one end of the grounding wire and place the bare grounding wire into the included copper

lug, and press firmly with the crimping pliers.

2. Fasten the copper lug to the grounding hole on the access point with the included M4 x6 screw.

Connecting the Ethernet Cable

To connect the Ethernet cable to the access point, perform the following steps using the Ethernet cable glands

that ships with your access point.

Figure 5 Installing the Ethernet Cable Gland

1. Remove the dust cap from the Ethernet port

2. Slide the sealing nut, clip, split grommet and gland body over the cable.

3. Insert the RJ45 connector to the Ethernet port.

4. Screw the gland body onto the Ethernet port.

5. Combine the two split parts of the grommet over the cable, and move it towards the gland body until it

locates at the recess of the gland body.

JW053A AP-270-MNT-V2 short mount kit for wall and vertical pole mounting, 75 mm from

vertical mounting asset.

JW054A AP-270-MNT-H1 mount kit for hanging from inclined or horizontal structure.

JW055A AP-270-MNT-H2 flush mount kit for wall and ceiling mounting.

Table 4 Applicable Mount Kits for 318 Series Access Point

Part Number Description

The 318 Series access point does not ship with any mount kits. These mount kits are available as accessories

and must be ordered separately.

For installation instructions on AP-220-MNT-W1, AP-270-MNT-V1, AP-270-MNT-V2, AP-270-MNT-H1 and AP-270-

MNT-H2 mount kit, please refer to the AP-270-MNT-V1 Installation Guide, AP-270-MNT-V2 Installation Guide, AP-

270-MNT-H1 Installation Guide and AP-270-MNT-H2 Installation Guide respectively.

WARNING

Failure to use the included Ethernet cable glands can lead to connectivity and POE issues.

The cable is not included and must be purchased separately. Purchase a suitable UV-resistant, outdoor rated,

CAT 5E or better RJ45 cable for use with the access point.

Sealing Nut

Clip

Gland Body

Split Grommet

8Aruba 318 Series Wireless Access Point | Installation Guide

6. Move the clip towards the gland body, passing over the grommet, until the wavy end of the clip properly fits

into the wavy end of the gland body.

7. Screw the sealing nut onto the gland body

Connecting the Fiber-optic Cable

To connect the fiber-optic cable to the access point, perform the following steps.

1. Remove the dust cap from the SFP port.

2. Insert the SFP module into the SFP port, and ensure it in place.

3. Slide the sealing nut, clip, split grommet and gland body over the cable.

Figure 6 Sliding the Fiber-optic Cable Gland Components over the Cable

4. Insert the optic fiber connector of the cable into the SFP module.

5. Screw the gland body onto the SFP port

Figure 7 Screwing the Gland Body onto the SFP Port

Two grommets are provided in the package for use with the Ethernet cables. One is applicable for cables with

4-6 mm diameter, and another is applicable for cables with 6-10 mm diameter.

The fiber-optic cable is not included in the package and must be purchased separately. Purchase a suitable UV-

resistant, outdoor rated cable for use with the access point.

When the fiber-optic cable (with the cable gland) is connected to the access point, the AP-270-MNT-H2 mount

kit is not applicable for mounting the access point.

When using the AP-270-MNT-H1 mount kit, the access point with the fiber-optic cable (with the cable gland)

connected can only tilt down 30 degree in maximum.

Sealing Nut

Clip

Gland Body

Split Grommet

Aruba 318 Series Wireless Access Point | Installation Guide 9

6. Combine the two split parts of the grommet over the cable, and move it towards the gland body until it

locates at the recess of the gland body.

7. Move the clip towards the gland body, passing over the grommet, until the wavy end of the clip properly fits

into the wavy end of the gland body.

Figure 8 Installing the Fiber-optic Cable Gland

8. Screw the sealing nut onto the gland body.

Figure 9 Completed Installation

Verifying Post-Installation Connectivity

10 Aruba 318 Series Wireless Access Point | Installation Guide

The integrated LEDs on the access point can be used to verify that the access point is receiving power and

initializing successfully (see Table 1 and Table 2). For instructions on initial setup and software configuration,

refer to the AP Software Quick Start Guide.

Electrical and Environmental Specifications

Electrical

Ethernet

One 10/100/1000Base-T auto-sensing Ethernet RJ-45 Interfaces

Power over Ethernet (IEEE 802.3at compliant)

Environmental

Operating

Temperature: -40ºC to 55ºC (-40ºF to 131ºF)

Storage

Temperature: -40ºC to 70ºC (-40ºF to 158ºF)

Humidity: 5% to 93% non-condensing

For additional specifications on this product, please refer to the data sheet. The data sheet can be found at

www.arubanetworks.com.

Regulatory Model Name

The following regulatory model names apply to the 318 Series:

AP-318: APIN0318

Safety and Regulatory Compliance

FCC

To view the FCC ID for controller-managed access points:

1. Log into the controller WebUI

2. Navigate to Maintenance > Controller > About

To view the FCC ID for Instant access points:

1. Log into the virtual controller WebUI

2. Navigate to Maintenance > About

CAUTION

RF Radiation Exposure Statement: This equipment complies with RF radiation exposure limits. This equip-

ment should be installed and operated with a minimum distance of 13.78 inches (35 cm) between the radiator

and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in con-

junction with any other antenna or transmitter.

CAUTION

Déclaration de la concernant l’exposition aux rayonnements à fréquence radioélectrique (FR): Cet appa-

reil est conforme aux limites d’exposition aux rayonnements FR établies par la FCC. Il doit être installé et utilisé

à une distance minimale de 35 cm (13,78 pouces) entre le radiateur et votre corps, qu’il opère sur la bande 2,4

GHz ou 5 GHz. Cet émetteur ne doit pas être installé ou utilisé à proximité immédiate d’une autre antenne ni

d’un autre transmetteur.

CAUTION

The device could automatically discontinue transmission in case of absence of information to transmit, or ope-

rational failure. Note that this is not intended to prohibit transmission of control or signaling information or

the use of repetitive codes where required by the technology.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Aruba

Aruba

Aruba RAP-5WN Manual de usuario

Aruba

Aruba AP-277 Guía del usuario

Aruba

Aruba Instant On AP11D Manual de usuario

Aruba

Aruba 650 SERIES Manual de usuario

Aruba

Aruba 200 Series Manual de usuario

Aruba

Aruba 207 Series Manual de usuario

Aruba

Aruba AP-277 Manual de usuario

Aruba

Aruba AP-205H Manual de usuario

Aruba

Aruba AP-120 Series Manual de usuario

Aruba

Aruba 220 Series Manual de usuario

Aruba

Aruba AP-105-MNT-C2 Manual de usuario

Aruba

Aruba RAP-108 Manual de usuario

Aruba

Aruba AP-505H Manual de usuario

Aruba

Aruba AP-65-MNT Guía de inicio rápido

Aruba

Aruba 210 Series Manual de usuario

Aruba

Aruba Instant On AP25 Manual de usuario

Aruba

Aruba 303 Series Manual de usuario

Aruba

Aruba RAP-2WG Manual de usuario

Aruba

Aruba AP17 Manual de usuario

Aruba

Aruba AP 70 Manual de usuario

Aruba

Aruba 387 Series Manual de usuario

Aruba

Aruba AP-130-MNT-C2 Manual de usuario

Aruba

Aruba 324 Manual de usuario

Aruba

Aruba 500 Series Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario

EnGenius

EnGenius EAP350 Manual de usuario