Arrow COMMANDER SERIES Manual de usuario
www.arrowsheds.com
01AG
NOTE: These instructions are to be used to add a rear door to an existing Arrow
Commander™ or Mountaineer™ Shed. If you are assembling a Commander™
or Mountaineer™ Shed as well as a Door Kit, use the manual included in the
main carton (C1GA).
Follow all safety precautions in the Commander™/Mountaineer™Series
Assembly Manual.
Two to three people are required for assembly.
Note: It may be helpful to refer to the primary Commander™/Mountaineer™ Series Assembly Manual you used when you fi rst assembled your
building. If you have misplaced your original Commander™/Mountaineer™ Series Assembly Manual, it is available online at www.arrowsheds.com
or you may request an additional copy from customer service: 1-800-851-1085.
COMMANDER™SERIES
Gloves must be worn
at all times to reduce
risk of injury!
719670514
* See Inside for Detailed Safety Information.
MOUNTAINEER
™SERIES
(Door Kit)
Owner’s Manual
& Assembly Guide
2
BEFORE YOU BEGIN...
Safety precautions MUST be followed at all times throughout the construction of your building!
•Care must be taken when handling various pieces of your building since
many contain sharp edges. Please wear work gloves, eye protection and long
sleeves when assembling or performing any maintenance on your building.
•Practice caution with the tools being used in the assembly. Be especially
familiar with the operation of all power tools.
•Keep children and pets away from the worksite during construction. Do not
allow children to help with assembly.
•Do NOT attempt to assemble this kit on a windy day. The large panels can
catch the wind like a “sail”, causing them to be whipped around making
construction diffi cult and unsafe.
•At least two people must work together to assemble this kit. This will make
assembly faster and easier.
•You must securely anchor once assembled in the same manner as your
existing Commander™/ Mountaineer™ Shed.
•NEVER concentrate your weight on the roof of the building. When using a
step ladder make sure that it is fully open and on even ground before climbing
on it.
02J
Below is a list of things you will need for installation.
• Work Gloves
• Safety Glasses
• Step Ladder
• No. 2 Phillips Screwdriver (Magnetic Tip Preferred)
• Utility Knife or Scissors
• Pliers
• Carpenter’s Level
• Tape Measure
• Power Drill (Cordless, Variable Speed)
• Nut Driver or Wrench
• Square
• String (for squaring the frame)
• Awl (to align holes)
WHAT YOU NEED
RECOMMENDED TIME SAVERS
3
HARDWARE LIST...
03AG
1
11/32 Hex.
Key Part Part Qty.
No. No. Description List
1 65103 Hex Nut (#8-32) 122
2 65106 Square Nut (#10-32) 20
3 65923 Small Bolt (#8-32 x 3/8) (10 mm) 86
4 65943 Large Bolt (#10-32 x 7/16) (11 mm) 14
5 65004 Small Screw (#8AB x 5/16) (8 mm) 112
6 66611 Large Screw (#10AB x 1/2) (13 mm) 133
7 66625 Long Bolt (#10-32 x 3/4) (19 mm) 2
8 66783 Flat Head Screw (#8-32 x 1/2) (13 mm) 36
9 66646 Washer Sheet 4
10 66609 Hinge 6
11 66778 Lock Eyelet 1
12 66781 Spring Latch 1
13 67293 Weather Stripping 1
14 10651 Latch Plate 3
15 66779 Slide Bolt 1
16 66780 Cane Bolt 2
17 66782 Door Handle 2
9
11
13
#2 Phillips
SS
5
#2 Phillips
3
#2 Phillips
LS
6
10 12
7
#2 Phillips
LNB
8
#2 Phillips
FS
4
#2 Phillips
LB
2
#10-32
14
16 17
Various fasteners are used throughout the
construction of your kit. In each step you will
see the abbreviations listed below used in the
illustrations to help you identify which fastener
to use. The fasteners used in each step are shown actual size at
the top of each page. If you are unsure which fastener to
use, hold it up to the picture and use the one that matches.
SB - Small Bolt
SS - Small Screw
LB - Large Bolt
LS - Large Screw
FS - Flat Head Screw
LNB - Long Bolt
At the top of each page you will see
one or more Part Cues like the one
to the right. These Part Cues are
designed to help you quickly identify
the parts needed for each step.
10629
Rear Frame
4
Part No.
Quantity Needed
End View
Part Name
SB
SB
QTY 18
15
Hardware Views by Key No.
SB
6
Key
No.
Part
No.
Part
Description
Qty.
List
110618 Front Wall Panel 2
210622 Right Door Jamb 1
380037 Left Door Jamb 1
410627 Front Wall Channel 6
510628 Front Wall Diagonal 4
610638 Long Fascia 1
710639 Short Fascia 1
810640 Wall Post 2
910652 Wall Post (Hinge) 2
10 10673 Front Frame 2
11 10623 Door Panel (Hinge) 2
12 10624 Right Door Panel 1
13 80051 Left Door Panel 1
14 10635 Horizontal Door Brace 4
15 10678 Vertical Door Brace (Latch) 2
16 10637 Vertical Door Brace (Hinge) 2
17 10647 Top Door Trim 2
18 10648 Door Astragal 2
19 10626 Door Diagonal Brace 8
20 10636 Vertical Door Brace 4
21 10675 Cane Bolt Bracket 2
22 69835 Edge Trim (Green) 2
6
10
7
3
14
1918
17
5
2
15
9
8
16
20 2221
PARTS LIST...
4
04AG
Selected End Views by Key No.
4
Confirm that all hardware
and parts are present before
attempting to assemble your kit.
For missing or damaged parts,
contact Customer Service. Do not
return to store.
Part Numbers
Part Number
1. Each part has an identifying part number on it.
2. Part Numbers are referenced in each step.
3. Unpainted parts have a stamped in number and painted
parts have a number that is inked on.
Remove inked on numbers with soap and water after assembly.
Customer Service:
1-800-851-1085 or
UnpaintedPainted
Painted
Painted
Painted
Painted
Painted
Painted
Unpainted
Unpainted
Unpainted
Unpainted
Unpainted
Unpainted
Unpainted
Unpainted
Unpainted
ASSEMBLY BY KEY NO.
5
05AG
Left Door
11
19 19
19 19
19 19
19 19
14
20
16
17
18
21
15
13
20
Right Door
15
11
12
20
20
16
21
Door Kit
1
1 8
8
9
9
2
3
5
5
5
5
4
4
4
4
4
4
6
7
10
10
14
14
14
18
17
6
Step 1: Disassemble Rear Wall
Remove the rear Roof Trim Caps and Roof Trim
from both sides of building.
1
Remove Peak Cap and four (4) Bolts and Nuts from
rear Ridge Cap.
2
Remove the last full-size Roof Panel and End Roof
Panel from both sides of building.
3
Remove the rear Ridge Cap by removing two (2)
Bolts and Nuts towards middle of building.
4
06AG
1
2
3
4
2
14
IMPORTANT: Take care in
removing parts from building.
They will be reused later.
Remove Parts:
• Roof Trim Cap (2)
• Roof Trim (2)
• Peak Cap (1)
• Roof Panel (2)
• End Roof Panel (2)
• Ridge Cap (1)
don’t focus weight
on roof
Remove four (4) Bolts
at end of Ridge Cap.
Remove Roof Trim Remove last
two (2) bolts.
7
Step 1: Continued
Install Edge Trim to top edge of Gables.
5
Remove Roof Beam Brace.
6
Remove two (2) side and main Roof Beams.
7
Remove Gable Brace, Track Supports, and Gables.
8
07AG
5
7
8
6
6
5
Edge Trim MUST
cover Gable edge.
7
Remove Parts:
• Roof Beam Brace (1)
• Roof Beam (4)
• Gable (2)
• Track Support (2)
• Gable Brace (1)
Install Edge Trim to cover
Gable Edge BEFORE doing
ANY work with Gables.
Failure to do so could result
in injury.
Edge Trim
2
69835
IMPORTANT: Take care in
removing parts from building.
They will be reused later.
69835
You will need for this page:
8
Step 1: Continued
Remove last Wall Panel from both sides of the building. Remove top,
middle, and bottom Screws on Adjacent Wall Panel as shown.
Remove Side Wall Channel.
9
10
08AG
9
9
10
10
10
Remove Parts:
• Wall Panel (2)
• Side Wall Channel (2)
Remove
Remove
Remove
IMPORTANT: Take care in
removing parts from building.
They will be reused later.
9
Step 1: Continued
Remove rear wall from building.
12
Remove Anchor Bolts from rear wall.
11
Remove rear Corner Panels.
13
09AG
12
13
13
IMPORTANT: TWO (2) PEOPLE SHOULD BE SUPPORTING
THE REAR WALL AS IT IS UNFASTENED!
Remove Parts:
• Corner Panel (2)
IMPORTANT: Take care in
removing parts from building.
They will be reused later.
10
Step 2: New Rear Wall Assembly
10AG
You will need for this page:
(QTY: 24)
(QTY: 34)
Insert Front Wall Diagonals into the Front
Wall Assembly as shown and secure with
Large Screws.
3
10640
Wall Post
210652
Wall Post
(Hinge)
210627
Front Wall
Channel
610628
Front Wall
Diagonal
4
Left Front Wall Assembly
10640
10640
10652
10652
10627
10627
10627
10628
10628
10628
10628
10673
10639
Fascia pieces should fi t inside Front Frame as shown.
10673
10673
10638
10639
10673
Front Frame
2
10638
Long Fascia
110639
Short Fascia
1
Lay out the parts and position them as
shown. Double check that holes align as
shown. If holes do not align, the Wall Post
(Hinge) is most likely upside-down.
1
2
Insert the Front Wall Channels into the
Wall Post and Wall Post (Hinge) as shown
and secure with Small Bolts and Nuts.
Assemble two (2) Front Frames together
with the Long and Short Fascias as shown
below and secure using Large Screws.
4
Right Front Wall Assembly
Door Header Assembly
LS
SB
LS
LS
LS
SB
SB
SB
SB
SB
LS
SB
SB
SB SB
SB SB
LS
LS
LS
LS SB
LS
LS
SNAP
10627
10627
Part 10627 Front Wall Channel may be joined in
pairs. Bend to separate.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Almacenamiento al aire libre de Arrow
Arrow
Arrow HM8667 Manual de uso y cuidado
Arrow
Arrow SCG1212CC Instrucciones de uso
Arrow
Arrow ED108 Manual de uso y cuidado
Arrow
Arrow SBS64 Instrucciones de uso
Arrow
Arrow BY1012-A Manual de uso y cuidado
Arrow
Arrow EZ8772HVCR Manual de usuario
Arrow
Arrow CM1014-A1 Manual de uso y cuidado
Arrow
Arrow CPHC142014 Manual de uso y cuidado
Arrow
Arrow LW108FB Manual de uso y cuidado
Arrow
Arrow CLG1014CC Manual de usuario
Arrow
Arrow CPHC101507 Instrucciones de uso
Arrow
Arrow GD106-A Manual de uso y cuidado
Arrow
Arrow WR108 Instrucciones de uso
Arrow
Arrow VM1012-B Manual de uso y cuidado
Arrow
Arrow VT1210 Manual de uso y cuidado
Arrow
Arrow SpaceMaker PS53EU Series Instrucciones de uso
Arrow
Arrow VT1210-A Manual de uso y cuidado
Arrow
Arrow HM10867 Manual de uso y cuidado
Arrow
Arrow YS410-A Manual de uso y cuidado
Arrow
Arrow SCG1417CC Instrucciones de uso
Manuales populares de Almacenamiento al aire libre de otras marcas
Lifetime
Lifetime 6418 Manual de usuario
rollaway container
rollaway container ARPCA24 Manual de usuario
Duratuf
Duratuf Havelock Manual de usuario
X-METAL
X-METAL 4065 Manual de usuario
Outdoor Life Products
Outdoor Life Products FP2030 F Manual de usuario
Royalcraft
Royalcraft Faro 295L Storage Box Manual de usuario
