ARRI ARRIFLEX 435 XTreme Manual de usuario
ARRIFLEX 435
Modification of the ARRIFLEX 435
for single frame operation
As of: July 2000
ALL ARTWORK, PICTURES AND TEXTS ARE COVERED BY OUR COPY-RIGHT.
THEY MUST NOT BE COPIED FOR REPRODUCTION (E.G. ON CD-ROM DISKS OR INTERNET-SITES) OR USED IN THEIR ENTIRE FORM OR IN EXCERPTS WITHOUT OUR PREVIOUS WRITTEN AGREEMENT.
IFYOU ARE DOWNLOADING PDF-FILES FROM OUR INTERNET HOME-PAGE FOR YOUR PERSONAL USE, MAKE SURE TO CHECK FOR UPDATED VERSIONS.
WECANNOT TAKE ANY LIABILITY WHATSOEVER FOR DOWNLOADED FILES, AS TECHNICAL DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE.
2
Attention
The delivered MCM Print will be damaged if it is installed
for the use of the singleframe equipment in older ARRIFLEX
435/435ES cameras. In order to avoid this, the version
of the CMC print in the ARRIFLEX 435 has to be checked
before the delivered MCM print is installed.
To check the CMC Print version:
• Take the electronic cover, the functional expansion
module (FEM) and the video module off.
The CMC print is now visible in the 435.
• In the top right corner of this print, there is a number
shown like: 1030-23-71-00-01-D
• If the last letter of this number is an A or B the CMC print
of the camera has to be exchanged for a newer print.
Do not install the delivered MCM print!
Ask your local ARRI support for the installation of the
new CMC print in the ARRIFLEX 435.
If the last letter is a C, D or higher you can do the single-
frame conversion as described in this manual.
Safety Instructions
3
Safety Instructions
Warnings
In your own interest please follow the warnings:
Caution! –stands for danger of injury.
Attention!–equipment damage possible.
Note: Operational error possible!
General Safety Specifications
•Assembly and initial operation must only be carried out
by persons that are familiar with the equipment.
•Disconnect the unit from the mains before starting
maintenance or service!
•Repairs only by authorized specialist shops!
•Use only original replacement parts and accessories!
1. Safety
Important
Prior to beginning with any work on the camera, we ask you
to first read through these instructions very carefully and
then to decide whether or not you wish to perform the
modification yourself. Should you have the slightest doubt
or not feel competent to do the modification yourself, please
have the camera retrofitted by an authorized ARRI Service
Repair Shop.
Tools needed
•Allen Key 2mm, 2,5 mm, 3 mm
•Box spanner 4mm, 4,5 mm
•Tweezer
4
Safety Instructions
Product Identification
When ordering or in case of enquiries please always
advise type designation and unit serial-number.
Explanation of the Symbols
➪ photo refers to objects shown in pictures, photos or
graphs.
5
Modification Manual
2. Modification of the ARRIFLEX 435
for single frame operation
•Switch the camera’s main switch to the ”off”position
and disconnect the camera from the power supply.
Manually turn the mirror shutter in such a way
that the mirror edge is positioned vertically as
shown
➪
photo so that no damage is done to
the mirror when opening the camera.
Only turn the black hub of the shutter.
Take care not to touch the mirror surface!
6
Modification Manual
three fastening screws
screw
•Take the viewfinder off by removing the three screws
➪ photo.
•Remove the electronic cover and/or functional
expansion module (FEM) and the IVS ➪ photo.
•Completely unscrew and remove
the 3 short screws (M3-8 DIN912),
the 3 long screws (M3x30 DIN912)
and the small screw (M2,5x6 DIN912)
of the electronic cover ➪ photo.
For the time being, the 2 screws for the connector cap
➪ photo remain where they are.
7
Modification Manual
3 short screws for the electronic cover
3 long screws for the electronic cover
2 screws for the connector cap
small screw for the electronic cover
8
Modification Manual
plug
electronic cover
3 plugs
•Now pull off the electronic cover approx. 5 cm away
from the camera ➪ photo.
•Pull out the big plug ➪ photo.
•Lay the electronic cover aside in such a way that the
cables in the rear part of the camera do not need to
be disconnected ➪ photo.
•Disconnect the 3 plugs ➪ photo.
Caution: the connectors have metal plates for
locking purposes on the sides.
9
Modification Manual
10
Modification Manual
2 screws
connector cover
•Now the electronic cover can be completely removed
from the camera.
•Undo the screws of the connector cover ➪ photo
and remove the connector plate.
Note: Make sure to carefully store the plate with the
screws in case you decide to modify the camera
back to its original condition.
•Disconnect the two small plugs ➪ photo.
Caution: the connectors have metal plates for
locking purposes on the sides.
•Unscrew the 4 screws that hold the upper print ➪ photo.
•A 51-pin plug ➪ photo connects the top print plate
to the bottom print plate. Hold the print plate close to
the connector and pull out the print plate (in doing so
the plug is disconnected). The red and black cables
which become visible underneath remain connected to
the electronic cover.
Otros manuales para ARRIFLEX 435 XTreme
5
Tabla de contenidos
Otros manuales de Cámara digital de ARRI
ARRI
ARRI ALEXA 35 Manual de usuario
ARRI
ARRI ARRIFLEX 16 St Manual de usuario
ARRI
ARRI Amira Manual de usuario
ARRI
ARRI Amira Manual de usuario
ARRI
ARRI ALEXA Manual de usuario
ARRI
ARRI ALEXA Mini LF SUP 7.1 Beta Manual de usuario
ARRI
ARRI ALEXA Manual de usuario
ARRI
ARRI Hi-5 SUP 2.1 Cómo utilizar
ARRI
ARRI ALEXA Mini Manual de usuario
ARRI
ARRI AMIRA SUP 6.1.2 Cómo utilizar
ARRI
ARRI 535 Manual de usuario
ARRI
ARRI ALEXA 35 Manual de usuario
ARRI
ARRI Arricam System Manual de usuario
ARRI
ARRI ALEXA Mini Cómo utilizar
ARRI
ARRI ALEXA Manual de usuario
ARRI
ARRI AMIRA SUP 4.0 Cómo utilizar
ARRI
ARRI ALEXA 35 SUP 1.0.3 Cómo utilizar
ARRI
ARRI ALEXA Manual de usuario
ARRI
ARRI 535B Manual del operador
ARRI
ARRI Arricam Lite Manual de usuario
